Audi A4 Avant Rear Suspension Spring Replacement

Подписаться 57 тыс.

Просмотров 113 тыс.

50% 1

How to replace the rear suspension coil springs on a 2006 B7 Audi A4 Avant S line / Seat Exeo
Check out the diagnostic machine I use - diydaly.co.uk/products/phoeni...
Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site)
Check GSF Car parts - tidd.ly/34pZe7o (use discount codes on site)
Tools : 1/2” Dewalt impact driver - amzn.to/3e2Uff2
3/8 Drive Mini Impact driver - amzn.to/3iFCZ30
Socket set - amzn.to/3eGx2Ak
Ring Inspection Lamp - amzn.to/3gGWHcG
Torque Wrench - amzn.to/2VZ4CKu
17/19/21 wheel bolt impact socket set - amzn.to/3gDnBlP
Long 1/2" Ratchet - amzn.to/2Z5RhSC
Spanner set - amzn.to/2DlwUZm
Large Pry bar - amzn.to/2Cl9NNY
Pry bar set - amzn.to/2Zg2lg9
Copper hammer - amzn.to/2Z9bdUU
Small wire brush set - amzn.to/2AF96yH
Parts : Audi A4 Avant S line rear Spring - amzn.to/323CVEq
Bilstein rear spring eBay - ebay.us/yIjCC5
Copper Grease - amzn.to/38BWV1U
Suspension springs @ Euro Car Parts - tidd.ly/3ittMKH
Check out my other A4 B7 videos :
Rear spring replacement - • Audi A4 Avant Rear Sus...
Retro fitting cruise control - • How to Retro fit Cruis...
Oil and filter change - • Audi A4 2.0 TDI Engine...
Oil drive replacement - • Audi A4 Oil Pump Drive...
Timing belt replacement - • Audi A4 2.0 TDI Timing...
Window regulator replacement - • Audi A4 front window r...
Projector light retrofit - • How to retrofit projec...
or check out all my a4 videos on the playlist below.
• Audi A4 2.0 tdi B7 rep...
If you found this video useful, please Like Share and Subscribe to help grow the channel, and never miss any future content. ru-vid.com?...
Please also check out my website - www.diydaly.co.uk where you'll find top quality goods, tried, tested and recommended by actual mechanics.
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. This doesn't effect the price you pay!

Авто/Мото

Опубликовано:

8 июл 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 110

@diydaly 3 года назад

Parts : Audi A4 Avant S line rear Spring - amzn.to/323CVEq Bilstein rear spring eBay - ebay.us/yIjCC5 Copper Grease - amzn.to/38BWV1U Suspension springs @ Euro Car Parts - tidd.ly/3ittMKH Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site) Check "Car Parts for Less" - tidd.ly/2LNEwIn (use discount codes on site) Check GSF Car parts - tidd.ly/34pZe7o (use discount codes on site) Tools : 1/2” Dewalt impact driver - amzn.to/3e2Uff2 3/8 Drive Mini Impact driver - amzn.to/3iFCZ30 Socket set - amzn.to/3eGx2Ak Ring Inspection Lamp - amzn.to/3gGWHcG Torque Wrench - amzn.to/2VZ4CKu 17/19/21 wheel bolt impact socket set - amzn.to/3gDnBlP Long 1/2" Ratchet - amzn.to/2Z5RhSC Spanner set - amzn.to/2DlwUZm Large Pry bar - amzn.to/2Cl9NNY Pry bar set - amzn.to/2Zg2lg9 Copper hammer - amzn.to/2Z9bdUU Small wire brush set - amzn.to/2AF96yH

@jaycekoda6056 2 года назад

I guess im asking randomly but does anyone know a way to get back into an Instagram account? I was dumb forgot my login password. I would love any assistance you can give me.

@omariweston5316 2 года назад

@Jayce Koda Instablaster :)

@jaycekoda6056 2 года назад

@Omari Weston I really appreciate your reply. I found the site thru google and I'm trying it out atm. Takes quite some time so I will reply here later with my results.

@jaycekoda6056 2 года назад

@Omari Weston it worked and I actually got access to my account again. I'm so happy:D Thank you so much, you really help me out!

@omariweston5316 2 года назад

@Jayce Koda Glad I could help :)

@realjiver2 2 года назад

Best video I've seen on changing rear springs on an Audi A4.

@diydaly 2 года назад

thanks , glad to help 👍👍

@folkertuken8086 4 месяца назад

Bei diesem mechaniker wird eine original feder eingebaut und keine 4cm kürzere. Man sieht deutlich wie er die ohne quälerei einsetzt, das war mir sehr wichtig. Hoffe das keine schraube bei mir in der büchse fest ist.

@fernandodias4528 3 года назад

What a great video! I’m a young technician & wasn’t up to the task even though my colleagues were saying that it’s quite easy to do. You’ve given me so much confidence to take on the task. 👍👌💪

@diydaly 3 года назад

Glad you liked it! yeah the rear springs can seem a bit daunting but there not bad to do really.. I'm sure you'll get them sorted :) thanks for the comment

@turbowank16v 3 года назад

Good lad.only way to learn.get stuck in.

@taknmybeatings7036 Год назад

If you don't work with guys that can fix anything that you can tear up, find a new shop to work in.

@peterlucasse 2 года назад

Just finished the job and your help was very accurat

@diydaly 2 года назад

Thanks Peter, glad to help 👍

@nigelgreer5400 2 года назад

Huge thanks for this! I've watched and taken notes of what you have done as I'll I'll be doing this tomorrow.

@diydaly 2 года назад

Thanks for the comment , glad to help 👍👍

@nigelgreer5400 2 года назад

@@diydaly All went well, just a bit of a pain getting new coil in but job done so thanks again :)

@diydaly 2 года назад

@@nigelgreer5400 nice one , glad you got it sorted 👌👍

@pavloozernyy7713 3 года назад

Great video, new spring in without issues thanks to this 🙌

@diydaly 3 года назад

Nice one , glad you got it done & thanks for the comment.. much appreciated 👍👌

@sjmcgarrie Год назад

Thank you... very clear and informative. I'll get mine done now

@diydaly Год назад

👍👍 glad it will help

@My_man_G_UK 15 дней назад

You don't know how much your content means to me! 😂😂. Got car back from dealership and quoted £2.6k from my health check. Would you say to do both springs or just the knackered one? Keep up the great work mate 👊🏾

@diydaly 10 дней назад

Nice one , glad to hear it 👍👍 I’d do both the springs mate

@rogieflores8403 3 года назад

Great continent! Doing this on my own car. U dont even need an extra tool to push down the spring. Fantastic work!

@diydaly 3 года назад

Glad it helped! Thanks for the comments , much appreciated 👌👍

@robertficek7586 3 года назад

I had to do the same, its funny how these Audi springs break so often. My experience was far different, its a cramp area and needs a strong single sided spring compressor, i had to crank the spring compressor down very tight and even then only had a little bit of wiggle room to push the lower A arm down just enough to push the top seat in place. I have no idea how that A arm has that much twist to take the whole spring. The video makes it look way too easy but its not. My springs are different from the video though, they have the white-green-green green marks on the bottom non sport

@turbowank16v 3 года назад

@@robertficek7586 i agree.im in process of putting set of rear springs in my 2006 avant se non sports suspension and its and absolute pig of a job.to the point now where ive left the job for the weekend to start it next week with a fresh head.my father is even talking of dropping the subframe bolts to give us and extra inch of wiggle room/having bottom arm at less of an angle.plus on top of this ive put a set of lesforjos springs in front and now she sits ski high like a 4x4.its so high to the point where i really do want them out.i dont know if kyb would sit better.

@robertficek7586 3 года назад

@@turbowank16v Its not too bad, i used a single sided spring compressor bought on Amazon, and it worked out fine. The audi manual says you need to compress a min of 4 coils. Lowering the sub frame will help but is not necessary, i had to unbolt the top damper and either top or bottom hub bolts to allow the lower arm a bit of swing. i unbolted the top as its easy to remove and the weight of the hub helps push down the arm, but mark the alignment position if you do. If the springs are changing the ride height significantly then maybe you would need to loosen the suspension bolts and allow the bushings to resettle to the new height, this would also give you more room to install the springs. The factory ride height should be about 15-15.5 inch from the bottom of the fender to the hub center

@realjiver2 Год назад

@@robertficek7586 Same as mine. I didn't have a single-sided spring compressor so, I had to lower the subframe so that the arm would come down far enough to get the standard size spring in.

@37Spires 3 года назад

Good video 👍. Music did my nut tho, no need for it 😀

@diydaly 3 года назад

Thanks .. Sorry about the music! I’ve stopped adding it to my current videos 👌

@queuing89 2 года назад

Excellent video, have you done this job on standard suspension with longer springs, i barely got the broken one out and no hope of the new one going in Theres another video where they drop the subframe on its bolts to get them in

@diydaly 2 года назад

Thanks for the comment mate 😁, yeah I have a used a load of jubilee clips to close the spring up just enough to get it in!lol .. I must say since doing this video I now always drop the subframe as it’s the easiest way if you’ve got a ramp.. I usually undo the 4 main bolts and lower it on some vertical jacks enough to get the springs in 👍

@tayebqureshi3471 2 года назад

This is an awesome video, the best, It took me two hours, problem was pushing the control arm down. The car is still 1 inch lower than the driver side, new shocks also...any suggestions 🤔??

@diydaly 2 года назад

nice one, glad It helped! thanks for the comment, I can only really be the spring mate, have you fitted an s line spring? they are lower than standard

@Alecks1990 2 года назад

great Video, thanks mate!

@diydaly 2 года назад

Glad it was helpful! thanks for the comment 👍👍

@karolisberkmonas327 Год назад

good day. i want to cause my audi a4 b6 quattro cab butt. how could i do it and what part do i need? thank you. I will wait for advice.

Год назад

thanks for video, it helped

@diydaly Год назад

You're welcome!

@CarLifee Год назад

Just done my front ones on my b7 s4 what a twat they can be be doing my rear ones tomorrow your video definitely as help on showing how todo it.

@diydaly Год назад

Yeah that rears are a lot easier!

@gordonmccartney1136 2 года назад

Good commentary.

@diydaly 2 года назад

Thanks for the comment 👍👍

@nigelperry8246 Год назад

Nice job 👍

@diydaly Год назад

Thanks 👍

@MattiasPersson Месяц назад

Great video, thanks! How's that Garmin Fenix holding up?

@diydaly Месяц назад

🤣 still going strong mate!! 👍

@xmgcx1 3 года назад

Could I remove the anti roll bar first before the two big bolts on the bottom of the hub? In your video you done the two big bolts then the anti roll bar link after. I only ask as my spring is not broke so still under some tension and I would rather reach in there and undo the anti roll bar while the two big bolts are still on so no chance of getting my arms nipped! Great video, very helpful, cheers for posting it.

@diydaly 3 года назад

yeah you'll be fine to do it that way mate , thanks for the comments 👍👌

@xmgcx1 3 года назад

@@diydaly cheers for the speedy reply, much appreciated.

@diydaly 3 года назад

@@xmgcx1 👍👌

@adrianandrews3820 3 года назад

That was really good but i had just watched a video where they did it in 3 minutes, now i'm confused, you undid a lot more stuff, they just jacked up the shocks and took the shock absorber and the spring out, why did you take off all the other stuff first. Good old guy tip you said, start the bolt by hand to avoid cross threading 10/10

@diydaly 3 года назад

Thanks Adrian 👌 Was the other video the exact same year/model? I’ve done atleast 20-30 rear springs on a b7 estate now and my way is about the quickest I’ve found to safely do it.. glad you liked the tip ha

@dontmindletsplay 3 года назад

I have an A4 S4 b6. But as far as i know it’s the same. But when trying to put the new springs in they are a few cm too tall and i can’t get them in. They are exactly the same height as the old springs so it’s not that either. Any tips? I’ll be trying to see if i cant get one spring compressor on the springs today. But not too much space for them 😅

@diydaly 3 года назад

Thanks for the comment.. they can sometimes be awkward to squeeze in! one thing ive done before is clamp them up with a good few hose clips! not ideal but it can just get you the few mm you need sometimes!👍

@dontmindletsplay 3 года назад

@@diydaly Thank you for such a quick reply! But with some help and a spring compressor on one side of the spring i got them in! Hose clips is a solution i will remember for the future thou! Anyways, because the sub-frame came in the way i had to keep pushing the springs in while the person holding down the bottom arm released pressure, and it snapped right into place!

@diydaly 3 года назад

@@dontmindletsplay arr nice one , at least you got it sorted mate 👌👌👍

@ivanboiko8389 10 месяцев назад

Servus, Dankeschön 👍👍👍

@diydaly 10 месяцев назад

👍👍

@denesleo996 2 года назад

Can i make the same steps also for a b7 4x4 model?

@diydaly 2 года назад

It should be similar but tbh I’ve never done a rear spring on a 4wd so wouldn’t like to say 100%

@michaelderkacz5526 Год назад

Late reply but I just did an awd and referenced this vid. For anyone wondering in the future. This vid is 1:1 the same process. Dropped all 4 rear subframe bolts an inch for more pace. Probably didn’t have to though.

@saharok50leskov58 Год назад

Hi, please tell me how long does it take to install one spring and how much does it cost? thanks

@diydaly Год назад

I’d say around 1.5 hours , depends on the garages labour rate

@saharok50leskov58 Год назад

@@diydaly Thank you

@longbar2344 3 года назад

well that was a bastard but quicker than my 1st try 3yrs ago. took the top bolt off and both bottom ones. doh On my own on my drive this time i had car fully off the ground at the back end and used your guide

@diydaly 3 года назад

Haha nice one , at least it’s done done 👍👌

@michlyle5093 2 года назад

Great video… I wish I had a lift. If doing this on axle stands and a jack, can I do this all by just having the one side in the air or do I need both wheels off the floor? Thanks

@diydaly 2 года назад

Thanks 😃.. yeah you could do it with just 1 side jacked right up if need be mate

@michlyle5093 2 года назад

@@diydaly thanks for the reply, I couldn’t see any reason why not, so I just jacked the one side up… I think I was just nervous about doing my first spring and started asking daft questions. Got the old spring out in 20 minutes or so, only difficulty was splitting the control arm? From the hub itself. Now just waiting for the part to be delivered tomorrow and then fitting should hopefully go just as smoothly as removal. All was made much easier thanks to you :)

@diydaly 2 года назад

@@michlyle5093 nice one , glad to help 👍 .. yeah there not bad to do really .. that arm can sometimes be abit tight! 🤞 the new one goes in fairly smoothly

@chris4632 2 года назад

Not sure why you went this rout, there's two subframe bolts either side unbolt them and swing it down the spring will fall out.

@diydaly 2 года назад

I’ve done them by undoing all 4 bolts and dropping the subframe before which is not too bad a method but would be a right clat if you didn’t have a ramp ha

@chris4632 2 года назад

@@diydaly not to bad doing it on the floor just support the frame with the jack once the spring has been replaced its a case of jacking it up and relocating the bolts, just done both my rears took around an hour

@diydaly 2 года назад

👌👍

@abdulbeany1894 2 месяца назад

Hi on my audi b7 my rear one side sits lower than other standard suspension is that normal thanks

@diydaly 2 месяца назад

Shouldn’t do really mate

@abdulbeany1894 2 месяца назад

@@diydaly thanks my cars going in for airbag recall in few weeks so audi going to do free health check so i will find out if anything wrong as they will check all suspension thanks for your help

@diydaly 2 месяца назад

@@abdulbeany1894 👍 yeah I’ve got the recall too

@abdulbeany1894 2 месяца назад

@@diydaly good luck mate hope they dont damage the glovebox when removing for airbag i know the glovebox hinges break easy on these cars

@abdulbeany1894 2 месяца назад

@@diydaly will take video of mine before give in my car if they do damage anything have video it was not damaged before giving to them

@robertsmith1810 5 месяцев назад

Im guessing on a quattro its much, much harder. Garage job if patience is limited?

@diydaly 5 месяцев назад

Yeah it can be easier to lower the complete subframe is using a ramp too

@codycarlbeckstrom5813 Год назад

Can you make a video where you do one that wasn’t broken and that has tension on it ? 🤦🏻‍♂️

@vencislavpenev9902 3 года назад

Is it audi a4 b6 estate suspension same as this one?????? 🤔

@diydaly 3 года назад

Yeah pretty much , there may be slight differences but basically the same 👌👍

@vencislavpenev9902 3 года назад

@@diydaly thanks 👍

@diydaly 3 года назад

@@vencislavpenev9902 no probs , hope you get it sorted ok 👌👍

@MrVinimoto 3 года назад

😍😍

@diydaly 3 года назад

thanks 👍👌

@michalszczepanski6469 3 года назад

Hi is the audi a6 c6 a simillar set up ??

@diydaly 3 года назад

Tbh I’m not sure mate , I’ve never replaced a rear spring on an A6 , will try find out for you 👍

@queuing89 2 года назад

Yes its similar but not exactly the same, i have just taken a broken spring out of A6 C6 AVANT with standard suspension and the spring is longer and the well it sits in is deeper than the same model with sports suspension. Even with half a turn missing from the spring and the bottom arm levered down as far as it would go, it still had too much tension on it to remove it. I jacked the arm up to compress the spring and put two small ratchet straps through the spring and looped them around it three times on either side to hold it compressed while i levered the arm down and pulled it out, it was still a struggle and i then put ordinary spring compressors on it and tightened them until the straps came loose, removed the straps and loosened the spring compressors. Check the sticker inside the boot to see what suspension you have: 1BA Standard, 1BB Heavy duty (20mm higher), 1BC Special purpose, 1BD S4, 1BE Sport, 1BP Heavy duty (same height as 1BA but with limited bump), 1BT Heavy duty (7mm higher). I HAVE NO IDEA HOW I WILL GET THE NEW SPRING IN AS IT WILL NEED COMPRESSING TO FAR TO BE MESSING AROUND WITH HOLDING IT WITH STRAPS, COMPRESSED SPRINGS ARE NO JOKE AND IF YOU NOT 100% SURE HOW TO DO IT, LEAVE IT WELL ALONE.