Auto Switching to Battery Module l UPS for Router l Up-to 9 Hrs Backup l Modem UPS 

Bro amazing mere nearby ye module easily mil gye and maza a gya bhai 450 rs m bn gya ye to

Excellent and perfect presentation

Thank you.. this what I'm looking for. You save my day 🙂

Very Nice Sir👌

C’est excellent pour l’explication 👍✌️👏🏻

Внятно и понятно! Так держать!

good idea. ...thank so much

So the BCM Balanced 12v, must use the charge adapter lower 12,5v to charge, if higher ( ex: 13v) BCM Balanced will cut-off cause UPS doesn't work?

Bro please make an ups for wifi router with multiple output ports. By the way nice explanation and editing. keep it up bro

As far as I know, this 20A board doesn't have a balancing IC... the 40a and 60a versions already have a balancing IC. Is it true? Please tell me if this version 20a board already has a balancing IC

excellent thanks to you working trick 😊☺️😊 💯💯💯 and success ☺️☺️

You need a LI-ION charge controller board placed before the BMS. An economical option is a module board based on the CN3722 chip, which supports an input range between 40 and 12 volts. This way you can use a commercial 24 volt input transformer. The BMS protects the battery against internal overloads and external anomalies, but it alone is not capable of managing the battery charge. For the step down output module, I would choose a variant with an integrated voltmeter, since it has protection against inverted voltage at both ends.

Good

Good evening, I can use x 4 batteries 2600 mah or more. But charging them with a solar panel?

Why do we need a diode right after the 12V input? To prevent ad-dc adapter from being damaged by power from battery? Or when main grid is off to prevent electricity to flow to the adapter and save battery capacity? Thanks!

Mr. AK what if I use a 12v fan connector from a computer as the power supply? The wire is 26 gauge and can handle 2 amps. Is that too low for what the 3 18650's will ask for? Or will it charge safely just very slow?

nice here my questions why used DC to DC booster as BMS (Powerbank Module) will gives also output current 9V ~ 0.6A

mt3608 step up module k sath kitny lithium battery use kr skta hun

Please make more videos and guide us

Hii kya ham mobile phone k battery use kar sakte hai ?.

thanks for the awesome video bro .. just 1 question on diode .. will the diode get heat up .. could u please check once? is there any alternative for diode?

Sir 12v battery can charge 12v Router adapter.. Its very ezzz i want to make 1 ups for my router and onu

hello sir the content was super helful and amazing keep up the good work, but can i use MOTORCYCLE BATTERY instead of them ?

This might seem like a good idea but in practice there are multiple flaws with this design, first of a BMS isn't supposed to control charging so you risk damaging either the input powersupply or the batteries but connection it straight to the batteries. The batteries will also never be able to reach full charge anyway as they're fully charged at 12.6V which is more than the 12V input not even accounting for the voltage drop across the diode. At best the battery might get charged to 50%. Finally the out put is connected to a step-down module which in all fairness does make sense for the router in the video, but the vast majority of routers are powered by 12V which this setup can't handle and the comments are full of people not realizing this (you'd need a boost converter/step-up regulator for this). Please do not try this at home, it lacks safety and won't work for most applications there are other resources on how to do this in a much more appropriate way available online.

What should I do, if I want a dual output of 12v - one for router and other for optical fiber switch.

i am having 12v bike battery then there is no need of use BMS am i right. once the battery is full means the current will automaticaly cutoff and the current flow directly to the wifi router which component will handle this job.

Is bms m Charging ho rhi ki nahi y kaise pta chlega ????

does your setup charge those batteries as they wait to be used as back up if they arent full?

What about the voltage drop due to Diod?

Can I leave the power adaptor switched on in the input jack while the ups is in use? Will it overcharge the batteries or will my power consumption goes up?

If the bms module output 12v, do I need xl 6009 module to run in ac/dc a 12volt onu

Do I need to add a diode in output, which diode should I need to use 4007 or 5048 and I can i use 12v 10amp power supply to charge battery will it be safe

Very nice and helpful project and I am about to do it but I want to ask you. When I plug it into power socket 220V and I have the power on the UPS does it take power from the battery or the socket and if I keep using it like that is there a danger of burning it ? Thanks

does this setup blip power when it switches or is it completely uninterrupted?

What is the mah per battery you used and I have used 1n5408 diode is it okay and do I need to add a diode in output.

I have used buck booster pcb XL 6009. But the BMS output voltage is dropping to 4V when the XL 6009 pcb is connected. What to do ?

Sir , do you better flawless design with lot of improvements?

I have question about voltage booster module assume, we gave 11.1v to module and get 12v in output if it suddenly get 12 volt in input then the output voltage remain same to 12volt or increase?

is possible to use 6 battery with same BMS ? 2 grupo of 3 battery on parallel ? to increase autonomy in hours. thanks a lot. I am from chile 👋

Sir I have a question. Can i take two output of 12 volt from the single LM2596 for my two routers rated 12v 1 amp respectively? Waiting for your answer

Where do you buy these components ?? is it from Richie Street ?? and does this work ??

Hi, whata the difference between 3s 20A or 3s 10A. How does this matter on BMS

how mah battery will be used ??

Is it possible to add more baterries so they provide the 12v needed, perhaps using a different charge controller? Does the booster itself consume any current to work?

Is that need two buck module for 12v and 9v?

ভাই এটি কি সোলার কন্ট্রোলার দিয়ে সার্চ করা যাবে?

I also make a video about this ❤

My question, can you put the adapter outlet, so it can run for 24 hours plugged in, battery will not overcharge?

Sir

I have one question: so the BMS get 12v input (or 11.4 volt because the diode takes 0.6v) , can the BMS charge 12.6V to the battery?

Can I get two 12v output from this single buck converter? Please reply.

Can you tell me why my BMS shutdown automatic when I Am giving a load like 12v router ,samll LED bulb.

My router is of 12V. what will happen if dont use the buck booster pcb XL 6009 ?? is it neccessary ? Please reply

if you use this setup majority of the time with wall power like a router, theres no issue with overcharging the battery?

If I add 3 more battery and make it parale (to keep voltage at 12v and increase battery cappacity) to extends Router backup time, should I change BMS module? What BMS module type/specification you recommend? Thanks

what current is required to charge those 18650s in this BMS

Want to make 6v 3A dc to dc and connect it with a 3W solar can u show using the circuit which u are using

isko esa banana hai ki, apan adapter ki male diy ups me inout dekar rakhe aur ups se output wifi router ko. taki jab light jaye to adapter to off ho jayega aur ups apne aap battery mode me ho jayega... ye system karo bhai.... hume khud haatho se on off na karna pade.

Bhai Jan main nay ya circut banyan hai lakin in4007 charging k Dron heet bohat hota hai

the bms module output is 12v so why you used xl6009 booster module?

how can use number of lithium battery in this mt3608 step up module....plz reply

I’m sure this was posted with the best intentions and although it might work it’s not really ideal. Few things to note: If using a 3S battery, the battery voltage will discharge from 12.6V to about 9V. So it is not supplying the constant 12V as the factory power supply does. Lithium ion batteries need to be charged with some sort of constant current. I’m not quite sure how this circuit achieves this. I’d say the concept is there but lacking attention to the finer details.

Hi bro .. just 1 more question: 1) Is there a scope of adding a "RELAY" to your project .. as a substitute for diode(i have heard from a lot of ppl that the diode gets really HOT when you put it on 12v circuit) .. please help me with this .. i am looking for a substitute for diode .. could u please help me ..

Please is it available 4v 18650 battery? I got 3.7v only.Thanks & Regards..

The BMS discontinue the current flow as soon as hits below 11.5volts on the batteries. I have 6 18650 li_ion batteries connected to a 10A BMS 3S. The backup time is only a few minutes on a 12v 1amp internet modem. Please advise on how to increase the backup time. thank you

Wouldn't battery will be cahrging and disscharging at the same timer?

At a same time in or out use kiya ja sakt hai

What if you just skip this module and use the battery connected to the power supply. Current will be drown from the power supply, the battery will be fully loaded. When there is the outage battery will be used. Whta is the advantage of this module? Voltage regulator can be used to produce stable 12V. My router works fine for input voltage 9-24 so it has the regulator build-in.

thanks for this. However, could you please give the numbers of the modules you used?

Plz Help ,, I made it But my Onu Going off On after 30 Minute , But my router still on long time ,, how to incraise back up with onu and router ,,

How to make 12 v power and 2A WiFi router Ups

BMS has input current limit? Otherwise overcurrent 12V adapter when power returns no?

Bahj ya ya bna hwa hwa kha sa mily ga or price

how do you actually charge this battery pack? voltage?

Salam Sir, I've watched your video and made same power bank accordingly to the wiring but I'm facing issue. Router specs : 12V 1Amps UPS made 12V but I've used XL6009 as i think that it should give constant output voltages even input fluctuates o/p remains same. Now my issue, When my power bank is fully discharged and when the power from adopter is again arrived my router doesn't turn on properly as its power led blinks continuously and remain like that (Not turning on my router) until I turn my router off for once and turn it back on. what could be the issue. One more thing what is the purpose of diode on the output as 1N4007 has a voltage drop of almost 1V which is already drooping on the I/P also while charging the battery and supplying the router at the same time which leads to lower voltages 11v which I think could be issue as there are two loads one is battery that's completely drained out it needs to be charged and the other is router which also need voltages of its requirement ( but that router voltages can be maintained through Step up converter as it will give constant O/P Voltages but not current). Could it be possible that I try same voltage higher amps adapter so that as it need initial torque when it's charging the battery and the router at the same time as my charger that comes with the router is of 12v & 1Amps it's designed accordingly to the router. What are your thoughts on this kindly guide me through this problem thanks. Regards, Usama Zaib

can i use XL6009 ?

bro IN4007 hitting issue

Apakah bisa bms 2 s dicharger dengan charger hp 5 volt ditambah step up menjadi 8.4 volt,caranya bagaimana?

Can i use 10A bms board ? because i already purchased it 😢

XL6009 will reduce the back-up time. I hope we can avoid using it. What do you think. What will happed if we dont use XL6009. Is it neccessary ?

if i want to add a led light, where should i connect it bro?

I made this ups but when input power is off the ups works about 2 minutes then its not working,if i reconnect the input then its works ,please tell me the solution

ভাই ভুল করে যদি বেশি ভোল্টেজ হয়ে যায় তাহলে কি রাউটার নষ্ট হয়ে যাবে একটু জানাবেন দয়া করে ??????

Is short circuit protection available in this bms Please dont tell lie!

I m using diode 4007 in connected to bms as per ur diagram but the battery was not charging

Backlight

Heyy can i connect more battery in this same module ?

Does it support 12v 2a router

MAH ?

Dont use charging red or blue led please give me diagram connect with led thanks bro

सर मे ईस पर कॅमेरा लगा सकता हु कया सर 12.1amp का

Battery charger ho raha hai but backup bohot kaam mil raha hai

whers the diagram

Auto charge or not?

if we don't change the plug , there will be no direct connection between the router and the main current. the batteries will give the current 24/7 , which is not a good idea

4ell is not working for 3s! why?

How to charge it? The router charger is 9v

9

Diode heating problem solution

Charge system ❓