Baja Electric Skateboard using Hoverboard wheels (HoverSkateBoard)

Подписаться 433 тыс.

Просмотров 380 тыс.

50% 1

BOM list
j35.us/Skateboard
j35.us/3Dprint...
j35.us/2200mah...
j35.us/Power2S...
j35.us/4WD-Hub...
j35.us/HoverBo...
j35.us/Voltage...
j35.us/ShaftCo...
Electrical Schematic: j35.us/HoverSk...
********************************************************************************
FAQ:
1) Where can learn more about batteries? j35.us/DIYlithi...
2) Where can I buy Lithium Batteries j35.us/Lithium...
3) How can I Consult 1on1 with you? j35.us/PhanTime
4) Where Can I buy Solar Panels? Flexible - j35.us/136wFlex...
Glass - j35.us/100w-100...
DIY - j35.us/DIY-Sola...
5) Where can I buy a Battery Management System? kit.com/jehu/b...
6) What parts do you use on your Samba? j35.us/eSambaProj
7) What is the best fuse wire? I only use 1/8w resistor legs j35.us/Resistor...
8) Why not use Supercapacitors?
A. Batteries work better at this time, caps are rare and expensive devices that are very good at doing things not needed for storage systems typically.
********************************************************************************
Disclosure: When you click on links to various merchants on this Videos and make a purchase, this can result in the earning of a commission. Affiliate programs and affiliations include, eBay Partner Network, and Amazon..
********************************************************************************
My video gear - kit.com/jehu/v...
********************************************************************************
Follow me on Instagram j35.us/insta-jag35
Follow me on Twitter j35.us/twitter-...
Follow me on Facebook j35.us/Facebook...
********************************************************************************
If you would like support my Projects
Buy some of My Merch j35.us/Jehus-ME...
you can donate: j35.us/helpwith...
Donate BitCoin - 1PjhLF2vPueywwaoUMetZCLbC6rQiniyj7
or you can become our patron / jehu
********************************************************************************
sponsors
j35.us/jag35-2016
gabvwkey.com
j35.us/indiespo...
evwest.com
www.rode.com/pr...
********************************************************************************

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 672

@trickyriky1 6 лет назад

"more fun to build it than to buy it" Could not agree more :D

@memyselfandi6422 6 лет назад

Tricky's World I could not disagree more, due to the fact that, what if you came upon an issue and you couldn't resolve it, then you would have a non working product which you would possibly have spent a considerable amount of time and money on, which doesn't even work, where as, if you buy an already built and working product you get to have fun immediately.

@tristanmcleish3825 5 лет назад

@@memyselfandi6422 i disagree with your argument because building it trouble shooting it and fixing it and then having a one of a kind board is much more satisfying than just buying one that is just like hundreds of others and then when it brakes you don't have the knowledge or experience to fix it. or it is to me anyway

@memyselfandi6422 5 лет назад

@@tristanmcleish3825 You can *try* to troubleshoot any issues that may arise, but what if you can't resolve the issue/s no matter how hard you try, the end result being you end up with a non working product and wasted money. You also end up frustrated and think to yourself that, you should have bought a professionally built product which you could now being having fun with. I would prefer to have a professionally built product that looks neat and tidy rather than building my own product which would end up looking ghetto and may not be as sturdy as a professionally built product.

@Petr214 5 лет назад

@@memyselfandi6422 your problem isn't that you can"t resolve it.. it's that you don't even want to think about how to do it. Don't know how? Search, learn, educate yourself and try again. by just going out and buying stuff, you're losing a big part of the experience. People used to be more self reliant.. sigh

@memyselfandi6422 5 лет назад

@@Petr214 I'd still prefer to buy it rather than build it, because while you (for a hypothetical example) are building your ugly looking frankenstein monstrosity, I am off having fun with my pleasure to look at and use, professionally built by experts who know what they're doing, electric skateboard. So who's the dummy in this situation, the guy having fun immediately or the guy who is slaving away still *trying* to build his toy who can't have any fun until his toy is built ? Would you rather purchase a gourmet meal at a restaurant which was prepared and cooked by a professional chef or would you prefer to buy the raw ingredients and *attempt* to make that same meal yourself at home ? If you attempted to make that meal for yourself from raw ingredients, do you think it would taste as good as the meal cooked by the professional chef, of course it wouldn't. *by going out and buying things you're losing a big part of the experience* What I lose in experience I make up for and gain in immediate satisfaction, fun and pleasure and I save heaps of time. *People used to be more self reliant* Yes they did, but that was in an age where people had no choice other than self reliance. If people throughout the ages had a choice (they didn't, but if they did), I am pretty sure convenience would win out over self reliance every time. In this modern day and age only gluttons for punishment would voluntarily choose self reliance over convenience. To take this argument to the extreme, do you or did you : Make your own clothes by sewing material together to make pants and shirts and underwear etc. ? Most likely not because it's more convenient to buy rather than make your own clothes. Build your own house ? (hypothetically speaking, because a lot of people rent rather than buy or even build these days) Cut your own hair ? I could keep going with different examples but I think you understand where I am going with this ?

@weareallbeingwatched4602 6 лет назад

Those shaft couplings scare the crap out of me on an engineering level.

@heimdall4148 6 лет назад

whaha i thought the same

@husse843 5 лет назад

Totally insane in the membrain XD

@tristanmcleish3825 5 лет назад

ya no sh*t those trucks are not a straight shaft there curved no way in hell i would put that on my board with out welding it

@frankdelucey2137 4 года назад

Just tighten it up and drill a hole for a retaining pin(s). Problem solved through engineering. 😀

@tedhancock68 3 года назад

And they're over $20 each. That exceeds my total budget right there.

@HowToGuys 6 лет назад

Hey jehu, you can just reconfigure motor windings in delta configuration to get more speed .nice video by the way😉

@ahaveland 6 лет назад

More speed yes, but also less torque. It is possible to make it switchable between delta and star windings, so could use it like a gear shift. It would be a lot of fiddly work!

@powerarmor222 6 лет назад

They are already in delta configuration. Wye configuration is very uncommon in these small Perm magnet motors

@AufBerghofNAM 6 лет назад

Peeps Dropping knowledge... D0pe

@leeburrow3671 6 лет назад

Lol. “You just”. I admire people who describe rewinding a motor like that.

@Kallenator1988 6 лет назад

Lee Burrow You dont need to rewind to go from delta to y or vica versa. But granted I am sure it can be an awkward job.

@karolbuda 4 года назад

hi! is there the second part - which you mention at the end - how to speed up these motors?

@hommerdalor6301 3 года назад

Hello. To increase the speed change the rotor wiring to star instead of triangle.

@AnythingMike 6 лет назад

Who else is just watching this but know they will never build it??🤣🤣

@NiNjaTurtLe697 6 лет назад

Me.

@KBE87 6 лет назад

Yup!

@DisconnecteDaydreams 6 лет назад

If only i had money haha, I would turn an old motor bike into all electric

@skydrones2012 6 лет назад

Me too , because he's building crap board with crap stuff lol

@husse843 5 лет назад

Standard XD

@SamMeechWard Год назад

Could you recommend which shaft couplers I should use for a project like this?

@michaeld954 5 лет назад

wheres the update build i want to make one but has to go faster then 10mph

@mashedpotatoes5323 5 лет назад

Use a 14s or more battery

@Yotraj 5 лет назад

@@mashedpotatoes5323 Use taller tires.

@mashedpotatoes5323 5 лет назад

@@Yotraj that's pretty difficult with these types of hub motors because there's not a lot of aftermarket tires, it's possible to make your own tire with a mold but I personally wouldn't want to do that because it seems hard. You also lose a bit of torque with taller tires but I don't think that would really matter if you have 4motors.

@taetravels8502 5 лет назад

I have the parts but I need the guidance of part 2

@lil_weltthomas7118 4 года назад

But he's going way faster than 10 miles per hour

@stefvandenelzen 3 года назад

Thanks for the inspiration! I recently finished my board ( ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-DwR6UcDh2wY.html - ibb.co/MpwRHFh ) and adapted the hoverboard wheels from star to delta wiring (based on this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-qG8b6QkTnCU.html with subtitles on ;). This gives me about 35 km/h (21 mph) max speed and 15 km (10 miles) range.

@RomansapienMVision 2 года назад

That's a lot of work for a 10mph ride. I think you could have put the same amount of money to a faster e-skateboard on Amazon.

@harrvey 6 лет назад

Don't ride your electric skateboard in the sand. The iron from the sand will degrade your motors. Also, incasing batteries in 3D printed plastic is a very bad idea. It's brittle and will not last very long. It is not heat-resistant (unless you cover the batteries with Kapton tape). If you want a plastic enclosure, you should use injected molded plastic.You need to have some foam or rubber to cushion the battery pack from the deck. Keep the metal enclosure and use suspension trucks (avenuetrucks.com/).

@AJ77MESSI 6 лет назад

Great build man. Did you mange overvolting these hub motors or not yet. I am waiting for it

@EbikeSchool 6 лет назад

10s4p with Panasonic 18650B cells and 40A drain? uh oh, those aren't rated for that high of discharge...

@josipkupresak9659 2 года назад

Did you figure out how to increase max speed?

@dabocket445 Год назад

did you ever do part 2? i am really interested in this and can use your videos with my own setup edit: i believe i have enough battery cells, and hub motors. im interested in the speed controllers you used and i want to have the master speed controller wired to the wireless transmitter of my rc car remote for throttle. i also would like to know where you got the motor mounts for the trucks and if you machined them please let make a video covering all of these topics. big edit: i used my brain to look at the description of all the listed parts and its only a matter of time and money and if i decide to make a video ill make sure to credit you

@xapplimatic 5 лет назад

"It needs to go faster for adrenaline junkies" says the man with no helmet to keep him from spilling his brains on the ground if he flies head first into something…

@cameroncook975 4 года назад

We don't need this sort of negativity. Splatters away ma'am

@ahaveland 6 лет назад

Want! Definitely increase the voltage - it's current that kills motors more than voltage as long as the insulation holds up.

@johnmck9530 5 лет назад

Increasing voltage increases current. Current and voltage are linked.

@jonathanrodriguesdemiranda8583 3 года назад

Hey guys and jehugarcia , I just wanne say that I was inspired to build this DIY Skateboard and I have done that. It is finnaly finnished, and I have to say It works realy well but just like jehugarcia said the tork is there but the speed is missing. so I will overvoltage the hub moters to a 12s battery, now I'm running them on 36 Volt (42v). I think most people don't have that much money so this is the cheapest build there is(?) for me the final cost where around 260 euro's (303 dollar). It is a lot of fun! Thanks for the great video!

@mojohammad 3 года назад

Hi, I am also building a Hover Skateboard at the moment. How should I charge it / witch charger should I buy? I will connect 6 hoverboard batteries in parallel (total of 26ah on 36v on a xt 60 plug). Thanks for anybody that can help. Greetings from Germany

@Willy_Tepes 4 года назад

I'd mount that battery meter and switch in a housing over the front axle so you don't have your foot on it all the time.

@fleetcommand3499 2 года назад

Where's the update build

@paulshrider6048 Год назад

Paul shrider here I am interested in how much it cost for everything, and how much for a complete board??

@linusgk5042 5 лет назад

Where is the update? :O

@EnrysonFerraz 6 лет назад

SPOILER ALERT! If you drive on bump roads, the double side tape will not secure the battery.. i tested my self.. i use 3MM Double side tape and didn't work... after a wile driving the battery will fall.

@sandpiper1515 6 лет назад

Enryson Ferraz did you make one of these? if so what do I do with the little black connector with five pins from the hoverboard motor assembly, it's not exactly clear. It looks like he didn't even connect them but I wasn't sure.

@MarvinFuhs 6 лет назад

@@sandpiper1515 you dont need these this is for a other type of motor controller (sensored esc)

@MrCaesartheman 6 лет назад

did you manage to increase the speed of the motor? and what means did you use to accomplish it? thanks

@toptobottom247 6 лет назад

It seems like the ride is really smooth. I don't need to go 35mph on a board which by the way is extremely scary,

@RespondsToOnlyLosers 2 года назад

I only came here to see the wheels of the hoverboard being used and how you did so but no sir hub motors is not the way to go. And I don't believe that's just based off an opinion more so fact

@kayjayham4210 3 года назад

Part 2 please :/

@CrAzYDr1veR 6 лет назад

If those battery terminals get loose use wire and crimped terminals instead of solid connection from battery to battery :)

@ratheonhudson3311 6 лет назад

Excellent work! I also would recommend hub motors for the simplicity but yes they lack torque. What an awesome build and step by step showcase.

@efivip93 6 лет назад

nice build. just one tip, copper and brass workhardens, so using it to connect battery cells, while the board flexes might just break it after a while. cheers.

@ElmarBlok 6 лет назад

Next time, also do the price of the board🤑

@Pascal_Robert--Rc_Creations 5 лет назад

What about a bigger rubber over the tires? Bugger radius, more speed...

@HOTSHOT-ls1bc 6 лет назад

Can you please do a video of wiring it in delta!!!!!! I’ve been waiting for what it feels like months

@benm3574 9 месяцев назад

Me I'm stupid already started ordering parts

@alecericksen5739 6 лет назад

Wow the Ideas you come up with are so function I never would have thought about hoverboard wheels for a AT board . Bravo.

@Bravo-ry9st 6 лет назад

If I was young like you, I would agree with more speed, but after medical conditions slow you down and probably being double your age. I will settle just moving forward at 10mph.

@tuxostile4792 5 лет назад

jehugarcia podría ser q lo explicases en español??? yo el ingles como q poquito, y en youtube no me da opción de traducir al español en los subtítulos un saludo

@Erniesworld 4 года назад

Just built one, haven’t programmed the vesc yet need to figure that out but before I do I want to know if the hall sensor is needed or can i leave them off? Anyone know.... i’ve watched the video a couple times and don’t remember him speaking about that but I’ll watch it again so if you’re going to comment that I should watch the video please don’t.

@frankdelucey2137 4 года назад

I didn’t hear anything about a hall Effect sensor In the video either. When you figure out whether you need one or not can you re-post a comment under this comment. I think my kids hover board is on its last battery charge lol. Almost Time to Repurpose maybe into a powered yard cart.

@stocklitv1371 6 лет назад

with a VESC you can go faster

@f.a.msmartrepair. 4 года назад

U can just open and rewire the motor for speed

@RCCar215 4 года назад

Please tell me how i cant figure it out

@f.a.msmartrepair. 4 года назад

@@RCCar215 yess of course I will send u a video wait for some time

@ldhaber 6 лет назад

Any news on you collaborating with Corridor Crew on their boosted board battery?

@jehugarcia 6 лет назад

dont know who they are

@ldhaber 6 лет назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-S919PAzyGxY.html

@ghos.t4968 6 лет назад

They used be known as Sam and niko

@deagle50ae 6 лет назад

Please make this happen. Ren + JAG would be a great time. The Coridor Crew love their electronic mobility

@deagle50ae 6 лет назад

This would be an awesome collaboration. Ren loves his hoverboards, one wheels, and built an electric bike for his wife.

@jonah5908 6 лет назад

Hey I used to skateboard alot, this looks really cool. But you should make a board with good sliding wheels (zomboehawgs for example) and increase the abrupt acceleration so you can pull off some crazy downhill slides. If you search up downhill longboarding, you'll get what I mean!

@joaopedroLajoso 6 лет назад

You have alot of torque on the board, why don't you get bigger tires? 2 inches more, 2mph more! 5 cm more, 5kph more!

@jehugarcia 6 лет назад

Might have to

@pooorman-diy1104 5 лет назад

try it at beach sand please ..

@igbatious 6 лет назад

Jehu please wear a helmet, multiple people have passed away from esk8 injuries already. can you detail how u mounted the wheels to the trucks?

@jehugarcia 6 лет назад

I have a helmet, Use the linked shaft coupler to join them, not much to explain there

@moistpope 6 лет назад

Check out field weakening.

@SpookyDoopyDoo 5 лет назад

When you drive on a electric skateboard u have to drive with the motors in the back or in the front just wanna know whats better!

@jandastroy 6 лет назад

If you're concerned about the double sided tape you could 3d print some kind of a rail to epoxy down to the board with a channel for the wires and slots for each battery pack you'd probably be able to strap it down pretty easily. Sweet board!

@allatsakis5058 3 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YhvPJpmJgOk.html

@jonezcoronezreal2402 6 лет назад

I'm building a drift trike with parts from an old hoverboard and a bike! (And some steel of course)

@r34d_ 5 месяцев назад

bit late but how did you end up building it?

@jonezcoronezreal2402 5 месяцев назад

@@r34d_ Welded a frame with an old bike and some steel beams, built a battery from 18650 cells and powered the hub motors with some cheap Chinese esc from alliexpress, then some pipe cut to pieces mounted on the tyres to make it drift. Worked alright but a bit down on power haha

@LiviuDragon 5 лет назад

cool skateboard

@fabrizioblasio2783 5 лет назад

Were can I find the 3d printed STL model for the battery holder?

@gaspererjavec7108 6 лет назад

just go to 72V, problem solved. A friend made a scooter with one of those. You could use a odrive controller ang go to 48v

@Dakktyrel 6 лет назад

'Hover board' wheels...think about that. If it's a 'hover' board.....it has no wheels. Just sayin....fun build though

@hubertus323f 6 лет назад

Eboard?

@Buzzhumma 5 лет назад

I would have thought those motors were sensored!

@Hitngan 6 лет назад

You're doing about 13 mph

@warlockboyburns 6 лет назад

12.6

@carldavis391 2 года назад

I'm liking it 🏁.😎✌️

@cloudcent2991 Год назад

Pure masterpiece.

@Shmade0304 2 года назад

So many gems 💎 in your playlist .. can’t wait to receive my pcbs 🙌🏽🙌🏽🙌🏽🔋🔋

@phizicks 6 лет назад

That mustn't last too long. I got 80 cells and I go to work everyday for 4 days before the voltage drops to 36-37V. work is 1.1miles away, short but still fun ride to work

@isaacinmon4086 6 лет назад

Phizicks those must not be very high capacity cells 80 cells is alot

@phizicks 6 лет назад

800Whrs approx, and 4 days of riding and still got more to go, just slower than I like so I could increase extra rows to increase it to nominal 42V. my videos have some footage.

@lbabacar8653 6 лет назад

Whath is more better between those vesc Maytech 50a vesc Or HGLRC flipsky fsvesc SK8-50A witch is more better for mountainboard?

@3dChris 6 лет назад

How secure are those couplers?

@joaquinninoortega156 3 года назад

if you have existing esc could you just buy another one and solder it yourself? can you also share the diagram its like a 2 dual esc solder together. THanks

@atomicsmith 6 лет назад

It looks freeeeeking amazing. acceleration seems pretty good. Even 15-18mph would be workable...

@atomicsmith 6 лет назад

I'd also be interested in the hill climbing...

@mcduffchannel 6 лет назад

Bruh! Ive been thinking about doing exactly this to my board but as a 2WD. Youve answered my plausible question. Its a mod to a wowgo board so itll be 40v, so im curious to see how they behave.

@JuanJDumeP 6 лет назад

check out the voltage on the caps in the controller and build battery pack that would closely match that it should give u more speed. voltage = speed but you already know that ;) . thanks for the info about the hub couplers i have 2 hubs i wanna do something with but didn't have a clue as to how to mount them.

@robgibb3081 6 лет назад

try industrial Velcro for holding the batteries up

@MichaelBylehn 4 года назад

As someone who lives with lots of hills it would have been nice to see a test

@A-tech 5 лет назад

hi, you should be able to get 20mph out of them motors, try using the hall sensors

@hamishburnettbrowne9811 4 года назад

Ummm don't you need a 10s 4 p BMS so the cells don't get unbalanced????

@herozero7423 3 года назад

😍😍😍🇱🇰🇱🇰

@harishussainabdulrahim4648 5 лет назад

Can we charge our battery while its discharging?, like our cell phone, if we can do means, please give me that knowledge how to make that,

@jehugarcia 5 лет назад

Your charger just has to output more than your load and it will keep charging

@harishussainabdulrahim4648 5 лет назад

@@jehugarcia is it safe for charging

@harishussainabdulrahim4648 5 лет назад

@@jehugarcia I have another question, every battery having only one terminal point which is + and -- from this points only we are discharging and charging, while discharging time if i connect my charger cable on the battery terminal, is the load will suck the power from my charging cable or load will suck the power from battery only? Do you have any recommend circuit design for real time charge and discharge,

@mygamertag2010X 5 лет назад

You have no battery management system or do the individual cells have their own boards?

@LeonCamero 4 года назад

He has to install one. I'm interested in how to do a BMS on that casing. Looks clean.

@FranikNoriega 4 года назад

Hey buddy..... Dont put 48v to those motors.... All you have to do is add shims between the commutator and the stator so that the magnets are not directly under the windings. Watch this video and you will understand how to get more out of those $10 motors bro. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HiD6amSoVsg.html You can also look up variable field magnet motors on here. Use something better than double sided tape to hold those batteries on the board. Hook me up with a good deal for the tip broseph!

@burnzy56469 6 лет назад

Awesome video I'm not even into electric skateboards. But all jehu projects are amazing and inspiring can't wate for the second video. 👍

@MikemfPanik 6 лет назад

Thanks for the summer project

@HarperMarshallSkate 5 лет назад

I made one but with 1 wheel. I just uploaded a video about it if you wanna tell my what you think of it

@jmueller87 4 года назад

What esc are you using and how do you bridge them to one controller? Any help is appreciated!

@1managainsttheworld 2 года назад

If someone is still reading the comments, open your hoverboard hub motor. What you will find out is that the motors coils are in WYE configuration. Change it to DELTA configuration and it will make the motor spin approximately 1.7 times faster than before. WARNING: this may overheat your motor, so be cautious! I made a electric longboard with one hoverboard hub motor, vesc, vesc remote and power tool batteries. First the board drove ~11mph. After the modification with same battery voltage (36v) the board drove ~19mph. What you will loose is a bit of torque and the motor will heat up a bit. I drove the board up some really long hills and the motor was not even too hot to touch, just warm. I'm quite sure you will burn the motor if you also raise the voltage alot, so please be careful. The motor still has plenty of torque after the modification, so even with one motor you are able to climb hills. 19mph is plenty of speed for inexprienced riders, like myself.

@SRNAR8 3 года назад

since then hub have come a long way, some over 12kw or more in power and price is cheaper than a 7kw belt motor.

@teektalon3310 4 года назад

Good vid. However in my 40 yrs working as a mechanic, machinist, welder (I'm 57, finished trade school early) gotta say buddy only a Kamikaze warrior or suicidal maniac would use those axle/wheel couplings in this application.

@Jaultaub 4 года назад

Are those NCR18650B cells Panasonic or LiitoKala cells? I want to get a similar setup going and found a good deal on LiitoKala ones that I believe are not fake cells. Any experience with this stuff?

@minivipers 5 лет назад

how about power management system? what if a cell not balanced and overheated while you are charging(i mean 4 18650 battery in one case)? lets say you have 4 18650 cell in case and 2 of them are around %70 capacity and the other 2 18650 cell are about %40 percent . will charger spot the %100 full 2 lith-ion battery and continue to charge other 2 battery ??? or continue charging 4 of them even if its overheated??? i am confused...????

@RCUFOinterceptor 2 года назад

Maby 2 motors are enought for speed and 4 for torq.. 🤷‍♂️

@parioceanchicago 6 лет назад

Nice vid, too bad you don't wear an helmet.

@aidanhahn8855 5 лет назад

well you didnt use a BMS so have fun with your fire hazard #futurebuildgoals jkjk the board is awesome, I just built a 52V ebike, having way too much fun. Go install a BMS asap otherwise your cells will charge and discharge unevenly over time and create those wonderful hoverboard fires you mentioned.

@electrifiedreviews 6 лет назад

Dude super clever! Nice build. Oh and I'm doing a GIVEAWAY for an Inboard M1 on my channel right now if you need another electric skateboard. 😂

@1mc568 6 лет назад

Your Video Editing skills are second to none.

@Martin_esposito_FilmProduction 6 лет назад

you fu...smart thank you ! si good

@azimalif266 6 лет назад

Pretty good use of those motors.😁

@daniluchison 4 года назад

A company just came out with the Baja E skateboard. If you are not in it with them, u r a fool!

@SolarizeYourLife 6 лет назад

There is a restaurant and grocery would not allow me in with my ninebot mini because of the fucking hoverboards... Love to hear with the higher voltage! Sparks or spaz...

@james10739 6 лет назад

How about the like 8.5 inch tires or 10 inch I know they had 6 I'm not sure if that's what you already have or the 8.5 but obviously 10 is bigger not sure it that would provide more speed

@stevenc22 6 лет назад

Just build your own solderless battery boxes ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_Qd51dB8sGA.html

@weiming2124 6 лет назад

55mph, that dude is really asking to get killed

@vonn1334 5 лет назад

Wei Ming let people do what they want you live YOUR life in a hole don’t pull others down there with you

@OGSumo 4 года назад

OWR _VONNY he’s just saying it’s dangerous, he’s not going to his house and literally stopping him. He’s not stopping anyone from living their life. Don’t be such a baby.

@vonn1334 4 года назад

Adam Nope I’m just saying mind your business and tell him not to be a baby I’m a speed demon🤣

@OGSumo 4 года назад

@@vonn1334 The internet is everyone's business, one of the best aspects about it. Also, thinking about it now, couldn't you make an argument that you telling OP to not tell someone else how to live, technically telling him how to live?

@ericmartin2470 6 лет назад

you remind me of that guy in weird al's movie UHF; the one who had a show of exotic pets.

@charl-s 4 года назад

"There's the cheap ones..." Shows a $1300 Boosted Board

@daledyckman 5 лет назад

Look up something called stargate for electric motors. Think it would be something worth trying.

@mojolotz Год назад

Well... The tires look like shit but i imagine if you shop around you can find something better. Also i'd drill a hole in the trucks and connect the motors that way. The shaft couplers are easy but also hella ugly,

@Etrueyeei 5 лет назад

vocke.tv/lib/exe/fetch.php?media=20150722_hoverboard_sch.pdf what the 4 wires of charging pin does? can i exclude the entire board and charge directly from the external charger? the li po pack already contains BMS. do i just need to connect the 2 of 3 pins to the battery? black and red? thanks in advance.