Тёмный

Balance Shaft Chain Alignment On 5 Cylinder 3.7 L Vortec Engine - GMC Canyon, Chevy Colorado, Isuzu 

Motorcarnut
Подписаться 37 тыс.
Просмотров 8 тыс.
50% 1

If you’re replacing balance shafts or crankshaft, you have to re-align balance shafts and chains.
GMC Canyon 2004-2014
Chevy Colorado 2004-2014
H3 Hummer 2006-2010
Isuzu I370 2006-2008
❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video.
💰Save money on other vehicle maintenance and repairs :
Top 3 Reasons Why Your Car Won’t Start
• Top 3 Reasons Why Your...
Pittsburg Harbor Freight Engine Support Bar 1000lb. Capacity - Review& Install
• Pittsburg Harbor Freig...
How To Remove A VERY Stripped Lug Nut - When All Tools Failed - Guaranteed
• How To Remove A VERY S...
Cheap Way To Check For Bent Valves Without Removing Cylinder Head
• Cheap Way To Check For...
Brake Burning Smell? - Frozen Brake Caliper Replacement on Any Car
• Brake Burning Smell? -...
Brakes Dragging? And Not a Frozen Caliper?
• Brakes Still Dragging...
Save money and learn how to bleed brakes by yourself on any car
• Save Money And Learn H...
Why Does My Car Battery Die So Fast
• Why Does My Car Batter...
How to properly gap spark plugs
• Car Misfiring? Running...
Proper way to install valve stem seals
• Proper Way to Install ...
Hot Tip: Broken Stud Removal
• Hot Tip: Use a Torch f...
Remove a Broken Stud Below the Surface
• Remove a Broken Stud B...
Oil Bearing Clearance measuring - simple to understand video
• Oil Bearing Clearance ...
Symptoms Of A Seized / Locked Engine - How To Tell It’s Not A Bad Starter
• Symptoms Of A Seized /...
How to properly gap and install piston rings
• Piston Rings Replaceme...
How to check cylinder head or block deck for warpage
• Cylinder Head Warpage ...
Why is it important to replace the timing belt at the manufacture’s intervals
• Check and Change Your ...
Fast & Easy way to lap “grind” intake and exhaust valves
• Seating Intake & Exhau...
Replace Front Exhaust Flex Pipe on most 4 or 6 cylinder cars - Cheap Way
• Replace Front Exhaust ...
Better Throttle Response in Minutes
• Better Throttle Respon...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the
future.
#motorcarnut
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

Авто/Мото

Опубликовано:

 

16 май 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 17   
@murph0666
@murph0666 Год назад
Something you should note. The I5 is a Clockwise rotating engine. So when you are looking at it from the rear, you should be rotating in Counter-Clockwise. That ensures the engine is Clockwise when looking at it from the front / harmonic balancer.
@Motorcarnut
@Motorcarnut Год назад
Very true
@luisalejandrofigueroaviram7479
@luisalejandrofigueroaviram7479 Месяц назад
If im replacing the vvt sprocket and the timing chain, should i replace this one too? Or should be ok?
@Motorcarnut
@Motorcarnut Месяц назад
If it doesn’t have excessive play it should be fine.
@bridgetrobertson7134
@bridgetrobertson7134 5 месяцев назад
Haven't seen a single instance of anyone anywhere changing the bearings on those balance shafts. Even during a full rebuild. You have to assume there's engines out there with 500k-800k miles on those bearings after a rebuild or two because no one can do it.
@Motorcarnut
@Motorcarnut 5 месяцев назад
Very true!
@huggi3z08
@huggi3z08 11 месяцев назад
How many miles does this chain typically last?
@Motorcarnut
@Motorcarnut 11 месяцев назад
Depends on how you maintain your engine with proper oil changes. But typically 200k
@HaythamBuKhadra
@HaythamBuKhadra 11 месяцев назад
Is it thar same for 3.5 engine?
@Motorcarnut
@Motorcarnut 11 месяцев назад
Very similar
@CodyAdams-nv8od
@CodyAdams-nv8od Месяц назад
Is there a trick to getting the balance chain back on after removals
@Motorcarnut
@Motorcarnut Месяц назад
No, the same way it came off is how it goes on
@tylerbidiman4346
@tylerbidiman4346 21 день назад
Mine isn't going on easy. There's not enough slack. It looks like a sprocket has to come off and go back on with the chain just like the front timing chain but I'm not sure how the sprocket comes off
@Motorcarnut
@Motorcarnut 21 день назад
@tylerbidiman4346 did you remove the tensioner? Should be just enough to get it off and on?
@noahjasilaitis7139
@noahjasilaitis7139 13 дней назад
@@Motorcarnutyou have to remove the left sprocket(the one under the starter). It is left hand thread also. So you will have turn bolt clockwise to loosen
@Angeli.
@Angeli. Год назад
I never work in that engine 🙃🙃
@Motorcarnut
@Motorcarnut Год назад
They are decent engines but have weak crankshafts for some reason.
Далее
ПОДВОДНЫЙ ГЕЙМИНГ #shorts
00:22
Просмотров 1,4 млн
Colorado/Canyon 3.5 i5 Cylinder Head Removal
23:33
Просмотров 10 тыс.
Cylinder Leak Down Test
4:59
Просмотров 61 тыс.
distribucion colorado 5 cil. en linea
5:57
Просмотров 32 тыс.
HUMMER H3 Suspension Conversion on A Chevy Colorado
22:39
БМВ i4
0:29
Просмотров 2 млн