Part 2d: Depriming and Resizing In this video I will show you how to adjust your resizing die, apply case lube, and deprime your brass using a RCBS Rock Chucker Supreme handloading press. Original Blog Post: readysetreload....
FINALLY,,,, a reloading instructional video for the beginner. A step-by-step tutorial. I am a visual learner. Instructions confuse me most of the time so this is refreshing. THANK YOU for taking the time to put together these videos.
I prefer to deprime before I tumble/clean my brass. That way the primer pockets get cleaned at the same time. So I deprime and resize in 2 different processes. And yes, if you hang your depriming pin down more than .375, you risk breaking/bending it. hanging out an inch or more, it is no surprise you were breaking the 06 depriming pin.
Hey I'm new to reloading and have a question about this. Depriming before tumbling makes a ton of sense but doesn't doesn't the die resize and deprime at the same time? So wouldnt it not need to be resized after tumbling?
I slam something on my workbench which creates a visual spike in the audio graph once the videos are imported. I can then see where I need to sync them up to then it's just a matter of fine tuning. The process is similar to those white wooden things they slam down in movies when they cut scenes. Now I think those things even have a timer on them. :)
I originally found this video because I got brass stuck in my die (NIGHTMARE) and did not want to go through that again, figured I was missing a step somewhere. I was afraid I was going to have to buy another die set - just bought this one - this was my first go around with bottle neck ammo reloading. I just want to say thanks, this was most helpful and it was easy to follow. I would also recommend watching the other videos in this series, he really breaks things down and gives his reasoning behind why he does it.
Dont over lube your case you WILL dent it and don't over lube the inside of your case neck to much lube will weaken your powder over time! ! I'm not a now it all but have been reloading for 40 plus years and have learned the do's and Don'ts
This is a good starting point but you should really be measuring how much your bumping the shoulder... ideally .002 is how far u want to bump the shoulder
So when you have the primer pin set an 1" below are you only depriming and not sizing? Or are you depriming and neck sizing with one stroke? Because everything else I've watched says to set the priming pin 3/16" from the bottom.
3/16" is fine as long as the primers are popping. If your too short primers won't pop, if your too long you'll break your pin. At least from my experience....
Great video however, like all creators you could make it easier for viewers to locate videos if you could make videos in sequence, label them so the order sequence can be identified in the first sentence. I give up and move onto the next creator. Just my opinion of course.
Doesn't it make more sense to deprime first, then clean and resize then reprime?reprise?? This is how I'm doing, yes I have a 4 slot turret and could do it in 1 turn.
Set your resizing die down to just where the press cams over, somewhere between 1/8 to 1/4 turn. When you get the press to the top of the stroke and it stops, push down a little more force and you will feel the press pop (cam over) and that is perfect. Not too much force or too little.
@@Drivapete Perfect is a shoulder bump of 0.002" I like how this bench rest champion sets his die: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-htvk1UYOXm8.html
@@RetrieverTrainingAlone This is for beginners not for precision shooters. Beginners need to follow instructions and learn the tricks of the trade like shoulder bumping, neck sizing and bullet seating procedures as they gain experience.
I'm brand new to this so question may seem silly..lol but when you stuck the brush inside the brass that dont effect the powder..? Having the lube inside.
Better yet, use RCBS dry case lube, then theres no question. Or, if you roll your cases on a pad, simply turn the case mouth upside down and press the neck into the pad in a well saturated area of the pad. Lubes the inside of the case for both seating and resizing.
Hey man I've got a question! First off great video! Second off, ive set my depriming die up, and when I pull the handle down to resize and pop the used primers out it crumples the base of the neck, any thoughts?
Michael Berkhoven make sure your die is adjusted correctly. Die adjustment and brass length could both be reasons why this is happening. Those are the first two things I can think of....
@@ngirardo86 Try bumping the shoulder and shooting it in a different rifle than it was originally shot from. Try those bumped shoulder cartridges in a semi auto.
Well, i think is better to have a few years of reloading before making a video on it , and he tends to get side tracked with other things , and he needs to get better at the names of all the equipment and parts before making the video. It is important if you make a video for beginners is that your terms are accurate and to the point
I agree. As an experienced reloader (40 years) and retired educationalist I think these instructions are poor. There are far better RU-vid clips available on this topic.
