Best beginner clipper? How to Zero Gap the Oster Fast Feed 

You just litterly saved my clipper with the sanding down the edges 🙏🏽🙏🏽 i almost bought a new clipper and ceramic blade bcz i thought there was sum wrong with mine 😮‍💨 you are a life saver 🙏🏽

Mad respect for you and making different clipper tutorials for all the different clippers people have✊🏼

very good tutorial thank you I'm going to grab me a ceramic blade now 😁😁

Could you do a review someday on the Oster octane versus the Andis Supra ZR

I did everything now it seems like the ceramic blade doesn’t sit in the middle its off like a centimeter or less because when it turns on seems like it goes off the metal plate? Its that normal

I am a beginner in the barber world I need advice I have bought a whall clipper (designer) but I cannot work with that blade I want to put another blade which can I put

Hi man my one make a loud noise when I put quarts on it as if the ceramic blade is banging on the guards any ideas 👍🏻

I bought the fast feeds and they have been terrible for fading lines out. Makes sense now. I havent zero gaped it lol.

I did this, and every time I tighten the screws, the cutting blade slides forwarded and paste the comb.

Gracias, I like you video. I sure have to learn to zero gap my fast feed when I buy it. Question can I adjust the blade to trim my whole beard?

Does it make the clipper louder if I put ceramic blade

My issue is, since the Ceramic blade is a bit longer, when I fully open the lever the metal piece at 2:35 that holds the lever moves forward and touches the back of the blade so it rubs against it and will stop it if you fully open. Not sure if it's easily possible to sand the back of the blade shave off a bit?

Why do u consider this the best beginning clipper to use??

Is that what the blue FF looks like or did ya paint the chassis yourself. Seems much darker than the amazon pics

Great video bro is this the same way to zero gap the oster topaz?

I had to sand too. It wouldn't cut in the open position until I sanded. It didn't take much, just a little, but it won't work without doing that

i didnt know that

Where you bought this blade mate ???

no parcero yo emocionado porque pense que iba a hacer el review en español y no manin colborame con un video en español bro desde colombia gracias.

Необычно.

Wtz Up is It nessesary to change the top Blade**NOT THE CUTTING BLADE** to usé thiz siramick Blade???

Hey man whats the difference between this one and the topaz?

David Well explained...i did that to my fast feed but did not need to sand. just wondering where are you from ?

i didnt have to do no sanding on mine. u proly have to sand it cuz u push it up where that bar goes.....mine0 gapd perfect

To me they better then any other clippers

How much does the ceramic blade cost?

Is not supposed that the topaz come in 000.?

español

Step one Unscrew lever screw along with fast feeds logo on top. Step two Now all things off use a 150 grit sand paper. Smooth down big bump along with a little bit of gap on bottom bump. Step three Sanding will take long time. Make it smooth so ceramic blade can move clean. Put all pieces together. Do not loose screws or gold piece along with plastic rod on top. You should be able to move blade without horrible noise. Watch to see if blade moves fast. Done three clippers it's good for fades only not to take out bulk. Hope this helps.

if you reading this I would suggest not using sand paper. just swap the blade thats it. I had a pair of fast feeds that opened as far as the masters and ruined them by sanding. your cutting blade wont sit properly and will cause it to rattle. brought 3 more and still couldnt find one that opened as far

Get the coarse ceramic blade not the medium ceramic.

Dave...it's pronounced Oh-ster