BEST E46 M50 INTAKE INSTALL VIDEO - Is it worth it?

Подписаться 917

Просмотров 16 тыс.

50% 1

Whats up guys! In this video we install a M50 intake manifold on my 2001 330i E46 beater car! We got this swap kit from Pohlman Autosports and our tune from Chaos Calibrations. Do you guys think the swap is worth it on your E46? I will try to link all of the needed parts below. If you have any questions please leave a comment below and I will try to answer and help! - Jack
Filmed and edited by Alex Ortiz ‪@alexortiz4078‬
M50 swap kit
www.pohlmanautosport.com/e46-...
Oil catch can
www.maxpeedingrods.com/produc...
CVC hose adapter to run -10AN
www.dormanproducts.com/p-7184...
Needed OEM parts:
x6 11611717259 Intake Manifold Gasket
11611716174 Throttle Body Gasket
11611738629 Connector
13541738757 Intake Boot (Non ASC)
13411738185 Manifold To ICV Hose
13411738186 ICV To Intake Boot Hose
13411722944 Hose To Intake Boot Connector
MAKE SURE TO FOLLOW US ON SOCIAL MEDIA TO KEEP UP TO DATE!
INSTAGRAM
/ jack_davis_
FACEBOOK
/ jdavisdrifting
RU-vid
/ @jack_davis_
TIKTOK
www.tiktok.com/@jack_davis247...
#AMERICANFORCEDINDUCTION #BMW #BMWE36 #E36DRIFTCAR #CONDORSPEEDSHOP #WISEFAB #BCRACINGCOILOVERS #DNDPERFORMANCEINTERIOR #BIGDUCKCLUB #KONIGWHEELS #HOLLEY #HOLLEYPERFORMANCE #DEATSCHWERKS #GTRADIAL #LINKECU #FORMULADRIFT #DRIFT #DRIFTING #JDAVISDRIFTING #KEEPDRIFTINGFUN #LSSWAP

Авто/Мото

Опубликовано:

21 ноя 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 52

@Dubloxb 4 месяца назад

And what about oil catch can we have to install catch can?

@alexortiz4078 8 месяцев назад

Always a pleasure filming with my boy 🤙

@bestofhouseoficial 7 месяцев назад

You show is face to much 😅

@georgallasj 5 месяцев назад

Your camera man needs to show what your talking about instead of your face when your showing details. The PS bracket, the gasket matching, the porting.. he goes closer when you go to show detail but then leaves your hands and the parts off screen.

@jack_davis_ 5 месяцев назад

Thank you for the feedback! We’ll work on that and try to get better camera angles for you next time!

@Demnz 4 месяца назад

L camera man

@ConradBrander 13 дней назад

Seriously.

@albalushi_movies8828 Месяц назад

What about purge valve .cancel or not?

@jack_davis_ 12 дней назад

Deleted it

@hhn2002 7 месяцев назад

Subscribed 👊

@jack_davis_ 7 месяцев назад

Appreciate the support 🤘

@206dcoe 3 месяца назад

Can you go over the vacuum lines you installed separately? I wa shopping to see the connections you had in order to better understand why my install left my car running poorly.. A lot of videos are more close up with everything done but your set up is closest to mine! Please and thank you! I’ve watched this video maybe 30 times already trying to see how your vacuum lines are routed! Please!! And Thank you!!! (((:

@user-im5mu5ur2c 6 месяцев назад

Hey great video bro wish I’ve seen it when I did my swap. What have you done with the purge valve that vaporized gas ,does you just keeping it open and letting it vent to the atmosphere, and the tune deleted the check engine light for it ? Or have you connected it back to the manifold? Thank you

@jack_davis_ 5 месяцев назад

Sorry for the late reply! Our tuner was able to tune it out of the ECU functions and the delete the CEL as well. For me I wanted everything as simple as possible but if you wanted to keep the factory operation, you would need to tee in the purge valve to one of the intake vacuum ports.

@loloh7547 5 месяцев назад

What about the throttle body cable ? does anyone make a bracket for the ms42 style throttle body. I really don’t feel like ghetto rigging something out of the old one.

@jack_davis_ 5 месяцев назад

That’s a great question and I’m not sure on that honestly…. I would reach out to Pohlman Autosports or another company perhaps that offers these conversion kits! Wish I could help more!

@leightonkoopman3944 3 месяца назад

Yo bro. Cool content How did you run the idle valve line from underneath the intake into the induction. Which fittings did you use

@jack_davis_ 3 месяца назад

I used a aftermarket fitting that came with my cold air intake

@Jonmiller-M54x36 Месяц назад

Have you dont any further guides on this? Curious where the Oil Catch Can Exit is going to ? Thanks a lot !

@jack_davis_ 12 дней назад

Not yet but will do an updated video going over some of the details we missed

@mikolizazi 6 месяцев назад

Hi, nice video. It’s actually a CCV. Crank Case Ventilation valve

@jack_davis_ 6 месяцев назад

Thanks for the info

@not_kudzo6702 3 месяца назад

do you have to port your head if you swap to m50 intake manifold or can you leave it untouched?

@86_E30_Blondie 2 месяца назад

Better to make the ports match to the manifold for the best results. It can be done without porting but if you have it open than it can easily be done in under an hour.

@bmw330i2 6 месяцев назад

Nice video! What fuel injectors are you running with ? Stock m54b30?

@jack_davis_ 6 месяцев назад

Yes stock injectors for now

@lukko000000 3 месяца назад

I’ve done the same things using your video that was very helpful for me. Unfortunally i haven’t done the ECU setup actually and car have problems at low rpms. It’s like the engine flooded at 1500/1700rpms and run very rough. Do you think that the problem could be the DISA valve not removed from ECU? Thank you 🙏🏼

@jack_davis_ 3 месяца назад

Yes you will need a tune for the delete! Hit up Chaos Calibrations and he can get it fixed up for you

@lukko000000 3 месяца назад

@@jack_davis_ Thanks mate i'll do. I've just another question: you have put the fuel pipe vacuum of pressure regulator directly on M50 intake port or between MAF and throttle like sotck M54 inlet? Thanks again for help.

@jack_davis_ 3 месяца назад

@@lukko000000 yes correct I ran the “vacuum” line from the OEM fuel pressure regulator/filter to the OEM location on my aftermarket cold air intake

@lukko000000 3 месяца назад

@@jack_davis_ thanks buddy, actually i’ve this pipe pugged in the M50 port, direcly in manifold. I don’t know if the problem that i have depends from this, that actually i don’t have this pipe between throttle and MAF like OEM setup.

@jack_davis_ 3 месяца назад

@@lukko000000 the FPR small hose is not supposed to have full engine vacuum. You need to place it before the throttle body aka in non engine vacuum

@andronikosandronikou9587 7 месяцев назад

Bro i cant find m50b25 manifold i only find m50b20 manifold is it going to be ok to install on my m52tub28?

@nord4610 7 месяцев назад

the m50b25 has bigger ports so its not gonna be the same with an m50b20. But yes, you can put a m50 intake on m52tun28 casue ive done that. But the kits the sell for m54 dosent macht, throttle plate is diffrent so you have to craft your own one, and also u need injector specers for the fuelrail.

@jack_davis_ 7 месяцев назад

I’m not sure how difficult or different they are to swap honestly

@petarbaleta5514 6 месяцев назад

that means if you want to mount only the m50 intake manifold on the m52tub28, you can't get anything, but you also need other things?

@nord4610 6 месяцев назад

@@jack_davis_ its a bit different but not so much harder. The only thing is that there is almost no tutorial or information how to do it on the m52tu so you have to figure out some stuff by yourself :)

@nord4610 6 месяцев назад

@@petarbaleta5514 yea there is gonna be a problem with the throttlebody because they are diffrent boltpatterns, and the adapterplate they sell for m54 engines are not gonna work correctly for m52tu. And on the m52tu you have the fuel pressure regulator sits on the fuelrail which its not allowing you to get the fuelrail on correctly on the m50 intake. So you need to buy injetor specers to make it fit

@roberthilditch5382 8 месяцев назад

So you cut the brake booster and routed it under the throttle body any pics ''and what did you do with the purge/ evap valve exactly '' Also there's 2 vaccum lines on the f connector not sure if I missed it but what do you do with those 2? Thanks again I'm doing my swap soon

@jack_davis_ 8 месяцев назад

Yes I just cut the factory E46 booster hose and made it fit on the M50 manifold. I deleted the purge valve and tuned it out in the ECU via Chaos Calibrations. If you wanted to keep it all you would need to do is route it to one of the vacuum ports on the intake

@bestofhouseoficial 7 месяцев назад

What about the disa valve?

@bort46 7 месяцев назад

gets deleted and coded out with a tune

@jack_davis_ 7 месяцев назад

Yes correct

@josephsu95 6 месяцев назад

Ive got a e46 325ci, i got the m50 intake already at home, is it worth it?

@jack_davis_ 6 месяцев назад

Yes

@TomoReso 6 месяцев назад

no. It is easily one of the most overrated manifold ever. Ive literally dynoed more horsepower with m54b25 manifold on m52tub28 engine then with m50b25 intake manifold. Tune was adjusted too. Its funny that a lot of those videos tell about gains, and yet no1 does maf logs or dynos to support the claim. Apart from great intake noise, for stock engines, dont do it. M54b25 manifold is great. No choke point for your engine even at 7000rpm. Only if you opt for better cams, and 7000+rpm go m50 manifold.

@jack_davis_ 6 месяцев назад

@@TomoReso I totally understand what you’re saying however for our needs or a racer / mechanic / or just enthusiast I think the M50 and a tune simplifies the engine bay a ton and makes the car easier to work on when at the track. No more vacuum lines to break or fall off, no disa valve to break or start leaking, etc.

@TomoReso 6 месяцев назад

@@jack_davis_ That is very true, yes. If done correctly it simplifies things a lot.

@josephsu95 6 месяцев назад

Ah thanks for your expanded reply, so the only reason in my situation to do it would be for the noise then, id love some more intake noise so it feels more like a racecar. But im not sure if its quite worth all the hassle@@TomoReso