No video :(

BMW F30 328i COOLANT FLUSH & BLEED

Подписаться 1,9 тыс.

Просмотров 94 тыс.

50% 1

This video will show how to drain then top off your coolant in your F30 328i.
For this you will need the following tools and BMW parts:
- BMW coolant: rover.ebay.com/rover/1/711-53...
- 1 Gallon Distilled Water: Local store
- Pick tools: rover.ebay.com/rover/1/711-53...
- Various sockets: Local store or Harbor Freight
- Bucket: Local store
_____________________________________________________________
The F30 has 3 bleeding screws and you can find information on the process directly from BMW below:
Drain + Top Off Coolant Process: www.newtis.info/tisv2/a/en/f3...
N20 Coolant Amount: www.newtis.info/tisv2/a/en/f3...
Shop Bleeding Procedure: www.newtis.info/tisv2/a/en/f3...
More BMW How To's: www.newtis.info/tisv2/a/en/f3...
F30 n20 Fluid Specs: www.automobile-catalog.com/oil...
F30 n20 Specs: www.amsoil.com/AmsoilGarage/i...
_____________________________________________________________
F30 Bleeding Instructions:
1. Fill cooling system using the vacuum filling device, after completing the filling procedure, remove the vacuum filling device.
2. Overfill the expansion tank (to below the tank ventilation line).
3 Open the bleeder screw (1) with the expansion tank open.
4 Open the bleeder screw on transmission oil cooler (2) until coolant emerges without bubbles and then close it again. Tightening torque 17 10 8AZ.
5. Open the bleeder screw on radiator return hose (3) until coolant emerges without bubbles and then close it again. Tightening torque 17 10 8AZ.
6. Close bleeder screw on expansion tank Tightening torque 17 10 8AZ.
7. Massage coolant hoses (supply and return radiator).
8. Connect battery charger.
9. Switch on ignition and low-beam headlight. Switch on the low-beam headlights to perform the bleeding procedure. If the low-beam headlights are not switched on, the ignition (Terminal 15) will switch off automatically after a certain period of time and interrupt the bleeding procedure.
10. FES (driving experience switch) must not be in ECO PRO!
11. Set heater to maximum temperature and turn blower down to lowest speed.
12. Press accelerator pedal for 10 seconds to floor. Engine must not be started.
13. The bleeding procedure is started when the accelerator pedal is pressed and takes approx. 12 minutes. (Electric coolant pump was activated and shuts down automatically after approx. 12 min).
14. Then adjust filling level in coolant expansion tank to maximum.
15. Check cooling system for watertightness.
16. Close coolant expansion tank.
17. After the bleeding procedure, let the engine run until it is warm and the electric fan starts running.
18. If cooling system bleeding must be carried out again (e.g. if the cooling system is leaking), allow the Digital Motor Electronics to drop completely (remove the ignition key for approximately 3 min), then repeat from Section 3.
_____________________________________________________________
Song: Joakim Karud - Ocean (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Joakim Karud - Ocean (...

Опубликовано:

30 авг 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 134

@bretdietzmann915 3 года назад

I've been a mechanic for 40 years, and anybody who thinks German cars are poorly engineered knows absolutely nothing about cars. German cars are the finest engineered cars on the planet, I've worked on everything under the the sun, and German cars are the best hands down. Do your research before you make statements you know nothing about. The reason BMW does not use a drain plug, is that it could cause a failure point for a leak.

@whothecapfits 3 года назад

"The reason BMW does not use a drain plug, is that it could cause a failure point for a leak." More likely they want to discourage DIY types so they have to bring it into the dealership where they can generate more $$$ for BMW. As a mechanic, you probably won't agree.

@kabalmk5 3 года назад

@@whothecapfits totally agree with u... and they even make it hard on them selves so they can charge xtra xtra money.... I work on cars as well.. and I never see a car leaking from drain plug... that is just an excuse so they can make a lot of money..

@jacraest18 3 года назад

don't mention to this guy the oil filter adapter gasket on the e46 series.

@tinkytinkz 2 года назад

I dont give a fuck about a leaky drain plug, this process looks absolutely horrible. Getting rained on with poisonous coolant isn't on my bucket list. This should be better.

@DuckMcDuckinson 2 года назад

True!!!! I own a BMW 428i Coupe and it’s awesome. People use and abuse these cars and when people buy them used, they tend to carry over all the negligence from the past owners. Take care of these cars and they’ll take care of you!!!!!!

@dlloydgriffin1 2 года назад

So many videos in the BMW community are guys walking around shops with out of focus cameras trying to be influencers... thank you for making a video that is actually informative and helpful!

@RbNetEngr 2 года назад

Thanks for posting the full procedure. Sorry you had to get a coolant shower. One tip for mixing coolant - keep your empty BMW coolant jug, and then in the future, pour half of new coolant into the old coolant jug, and then add the water to both jugs. You’ll have your two gallons of mixed coolant, already in the jugs. No need to mix them in a bucket.

@raulmartinez3484 3 года назад

Apparently BMW demanded that Newtis stop providing people with service instructions. As a result, we can no longer access their site. If anyone wants to or knows about a class action lawsuit against BMW for not allowing owners to access service manuals please let me know.

@vladlozo1111 5 лет назад

I can't believe they haven't made a valve for draining the coolant. Jees!!!

@KL-er2ed 5 лет назад

thanks! saved me $220. you a real G! Subbed!

@K.T.789 5 лет назад

Thank you Matt!! This is very helpful, I will do it next week.

@leveragelifestyle8581 5 месяцев назад

Great vid. I think if you left the cap open for the fill talk while bleeding you wouldn't need to open the bleeder screws. The air comes out of the port that shoots the coolant back into the tank as it recirculates.

@manperformance9253 3 года назад

Thanks bro, you saved me $250!

@hallancorrea7507 5 лет назад

Obrigado pelo vídeo, bem elaborado e explicativo me ajudou muito. Obrigado

@carsinourdna9388 4 года назад

Great work!!

@RandomVidz9_ Год назад

Do u have to open up the screw during bleeding procedure? Cuz i mostly see them just pour coolant in then start bleeding procedure, they say the water pump will do the work and take out the air and then u just top it off with more coolant, is that true?

@peterkeilich7174 2 года назад

Outstanding instructions!

@MatthewWong 2 года назад

Thanks!

@larsgreen4292 4 года назад

how many liters of antifreeze does it take? ive got 328i 2012 n20 engine

@eloyalze 5 лет назад

Hello from Mexico City, thaks for the information that you give us, my best regards

@adeelahmed8641 6 месяцев назад

How many times would you need to drain coolant to get radweld out? It's blocked my heaters

@UrielTheGreatOso 3 года назад

Can I use this for my 2018 330i?

@Fly-SanDiego 6 месяцев назад

Flip flops and cardboard boxes. The standard for DIY garage mechanics for years.

@iamdarcside 2 года назад

Thank you!

@releasedmike 2 года назад

Is this the same Procedure as The f30 320d ed

@bombakdik 3 года назад

Apart from the funny combination of slippers and white socks, very good tutorial. Is that an E28 next to your car? I already discovered that newtis is down here in Europe... Your car was in eco pro though? Cheers from Belgium!

@anthonyantoine9877 5 лет назад

Any one has any info for me I have an 2010 bmw 328i xdrive my cooler looks brown and dirty in the coolant tank any ideas wht I should do of course I’m planning to do a plus

@alirikhotso3401 4 года назад

Thanks Matth,

@SOHAIL50280 Год назад

Thanks brother

@tek2313 5 лет назад

When you do the electric pump bleeding process should you keep the tank cap open or closed??

@MatthewWong 5 лет назад

The tank cap should be able to stay open. The tank is only for building pressure when the coolant is hot. You should only be leaving the bleeder screws open that way when it overfills at those areas it shows there are no air bubbles. The process is documented here: www.newtis.info/tisv2/a/en/f30-328i-lim/repair-manuals/17-cooling/17-00-cooling-check/HrgIPzMT

@RandomVidz9_ Год назад

Hey when adding coolant do you have to have all 3 bleeder screws open then when it starts leaking out coolant close it up and start bleeding procedure? If so how open do u have the bleeder screws all the way out or half way?

@MatthewWong Год назад

I tried all three at first until they started leaking out. Then I tried each individually about 2-3 more times to make sure there was no air

@NinjaTactiks 3 года назад

Hey, do you have any recommendations for the battery charger?

@MatthewWong 3 года назад

I just use the harbor freight cheap trickle charger.

@shyshai605 3 года назад

Would this work for a 428i 2015 ? I can’t find no videos on how to bleed coolant for a 4 series

@MatthewWong 3 года назад

Should be exactly the same!

@cultistpriest1872 3 года назад

What are u using to hold the front of the car up? What are they called ramps?

@MatthewWong 3 года назад

ramps

@demirunlusoy2795 5 лет назад

4 questions: 1- Will it be okay to use Castrol blue color coolant instead of Bmw Coolant? (I have always used it on my all E36 E46 E90 without having any issue). 2- Is it possible to remove the lower radiator hose from underneath the car without having to remove the air filter box? 3-Is there any drain plug on F30 radiator? 4-On F30 N13 engines without an electrical water pump, is it enough to remove the lower radiator hose for the draining process? Many thanks in advance!

@MatthewWong 5 лет назад

In order of your questions: 1. Im not sure this is the first coolant flush I've done on a BMW. 2. Not easily, the clip to unlock the pipe goes up towards the bottom of the air filter box 3. There is no drain plug on the F30 Radiator 4. I am not sure about the N13 engine

@demirunlusoy2795 5 лет назад

@@MatthewWong Sorted out. Removed the airfilter box and drained more than 5lt of coolant via lower radiator hose only. I have mechanical waterpump so skipped the electrical mechanial pump fill process. Used 50% 50% Blue color Castrol Radicool coolant and drinking water. Released air from both expansion tank and heat exchanger several times. So far so good. No need to pay extra for Bmw coolant.

@gokhankeskin985 4 года назад

Hey friend hello from turkey. İ wonder that lifting eqipman for lift up the car. İ want buy it but i couldnt find. Whats that name ? Where can i buy it . Thanks so much

@MatthewWong 4 года назад

The car ramps you can find on eBay here: rover.ebay.com/rover/1/711-53200-19255-0/1?ff3=4&pub=5575300093&toolid=10001&campid=5338084593&customid=&mpre=https%3A%2F%2Fwww.ebay.com%2Fitm%2FVehicle-Drive-on-Ramps-12000-lbs-Capacity-Car-Truck-Service-Repair-Shop-Garage%2F352602935374%3Fepid%3D14023040722%26_trkparms%3Dispr%253D1%26hash%3Ditem5218c5d04e%3Ag%3AN1kAAOSwB6Zcc4qG%26enc%3DAQAEAAACQBPxNw%252BVj6nta7CKEs3N0qXMuY16jR%252BKv9m77o3UJqE3U1N7Quf8Dm8fCMBrjshqG9MvXSmb2e%252FnAzaPUmKCTQAd%252BUh6jmu4UzLR6JugR3Qe5cGvEa6qWbuwLC8V5B1qpdfmzo%252FIUx1VpgFlMnuSzsA%252Bnbkb2tUsXnhRW0F%252F0UtcQdjgsUCym%252FgAYNyhq1tWzmBRD%252Fq%252Fl2bSmffZsT5A8A21x%252F955x6mEAqk5zGVeLUvfwD%252FfFbxjsIGxVBwtDhbPW%252FjpgyxCqdkBgJcB6FCknujEu75vE8kfSFvd6LoDM8ngPUV9z40cBA%252BJVekkwU94NTbB9OxhfXip4qSuuAEVhorh9E%252BxpTAkKhvEL0juoNfRZS07IXoF0XO7%252F%252BC6p8qZ6BFzlqjuXeVlgxP%252FUyDEt%252Fnuec0Oqbt1Z4JbutmKxKoAwD71NzkqV3amFvdViRgIcWsQTXeNapgNxyTm85vzat08%252F7%252BerX4sz9zfsV5nvrtkJ9qrgu5XjHD169sx6%252BpChS8tFUbfsMf65z7sv5reKB13pxemR4TNPt79kQO7wX4%252BrOLKwqy7ZO5SAOyUUN11WzfSCatULBZEFZMEdcz7A9suYdsktb38qypmQfBRppLmfl1rBvY4ztxQSFeBOdhrnyKKWYXN%252FpFzBf8iKiLpnUX5KwPZ5ZkKOX7QoIQMorsdcGS3EziQf9rGtOwCF54exISXm%252FT6r0A0yjQbfzfIS%252FZ%252F7ET3v7qhSWWBF%252FlMd1UmF%252F1XyTjxXQvYGnwmttyZg%253D%253D%26checksum%3D352602935374b1aac3d482704159928b27091b3d515c

@poomunj 4 года назад

How tightly did you torque down the hose clamp going to the water pump? Just finished doing my flush thanks to you!

@MatthewWong 4 года назад

I believe its 8-10nm however I just handtightend mine. Glad it helped!

@DrTentaCulo 3 года назад

Quick question, since I’m going to add some cooling into mine why is the old one that you took out clear but the new one is blue. I know that all the BMW coolant is blue but I was just wondering why yours was clear as well as mine that’s currently in the car

@MatthewWong 3 года назад

My car was originally in Arizona so they probably diluted with more water than anti-freeze. That is why its probably so clear. But depending on where you live you should adjust the ratio if its colder, or hotter.

@DrTentaCulo 3 года назад

@@MatthewWong thanks for the quick reply before I add some, I live in Cali so just picked some coolant to top it off since it’s at the minimum mark. I’ll just add some without diluting it then since it’s only a minimal amount, I was just wondering why it was so clear in mine LOL

@LukePerri 2 года назад

That dog barking sounded like a sick ass remixed song

@joseolvera1891 4 года назад

Do you have to bleed it every time you put coolant in?

@MatthewWong 4 года назад

If you are just topping off into the reservoir I don't believe you need to. Its only to purge the air out of the coolant pipes when you need to bleed.

@Brian84087753 3 года назад

Pour the coolant first until bubble come out , then only start bleeding process ?

@MatthewWong 3 года назад

When you pour the the coolant in it should force most of the air out. The left over air will be in the bends of the pipes and certain air pockets. Then you should begin the bleeding process which should pressurize the entire system. You can do this a couple times to be sure, or you can get one of those pressurized bleeders for the car also which should suck out all the air.

@kennethlimkl91 5 лет назад

Hi. Just want to know what if we never do the mix. Just pure bmw coolant. Will it harm the engine ?

@MatthewWong 5 лет назад

I don't believe it will damage the engine directly, however it might not be effective to the engine in low temps. I would recommend just mixing 50/50 always.

@paulvarley1054 3 года назад

@@MatthewWong It will definitely hurt the engine, pure coolant doesn't have the cooling properties of water, coolant is in there so water doesn't rush components and it lowers the freezing point of the mixture, water is the best for pulling heat out of everything

@MatthewWong 3 года назад

@@paulvarley1054 Thats good to know! Yeah I've always read that there are different mixtures for different climates but I never knew pure coolant was bad.

@anotherindividual5799 4 года назад

Just recently got one & the “service needed since” notification popped up exactly like the one showed in yours. Dealer said they flushed and did the oil etc. It’s the weekend and their closed rn, but I’m going to see what they say. But is there a way to reset that notification. I’ve seen videos on resetting the them, but that hasn’t worked for this notification. Maybe you can give me some information on that. Thanks, well informative video btw.

@MatthewWong 4 года назад

If its the oil notification ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ozRv0eZW0OU.html you can do something like this. However if its the coolant low notification there isnt anything you can do.

@anotherindividual5799 4 года назад

Matthew Wong it must be. Because it didn’t come off. Appreciate it.

@anotherindividual5799 4 года назад

Matthew Wong update. I played with it a little more and found it was the inspection of all things through the vehicle status settings on the screen 😂glad it wasn’t a real issue....At all.

@MatthewWong 4 года назад

@@anotherindividual5799 Glad everything worked out!

@mbo7613 Год назад

Update for anyone looking at resetting codes other than oil change, research Bimmerlink + Veepeak BLE.

@pericodelospalotillosverdes Год назад

This purging procedure is indicated by the mark, when the electric water pump is changed.

@KashifRoshni 3 года назад

Did you actually use the entire 2 gallons? I’ve only got 1.5 gallons of 50-50 in and it’s full now after bleeding. I have an F25 328xi with the same N20 engine. Please advise

@KashifRoshni 2 года назад

Response to myself after a year 😂. No, you won’t use all 2 gallons. More like 1.5..

@petenavajas5959 Год назад

@@KashifRoshni Thanks, was wondering why the whole 2 gallons didnt go in.

@tylergray6308 4 года назад

Not a flush. More like a Spill and fill. (Drain and Fill). Good info on bleeding procedure.

@user-zt7xd8oc6t 5 лет назад

Awesome video! Does the bleeder screw at the expansion tank has to stay open during the bleeding process?

@MatthewWong 5 лет назад

According to the documentation here: www.newtis.info/tisv2/a/en/f30-328i-lim/repair-manuals/17-cooling/17-00-cooling-check/HrgIPzMT You are supposed to leave the bleeder screws open only when refilling in the expansion tank. All bleeder screws should be open. Once they start overfilling thats when you tighten them down, then make sure that the overfill is at the min/ max. After that you can start the bleeding process.

@user-zt7xd8oc6t 5 лет назад

Thank you!

@AudioGetsLoud 4 года назад

Is it the same process in a 2014 bmw 435i n55 ?

@MatthewWong 4 года назад

Should be similar process. Just different bleed ports and draining.

@tatendak 4 года назад

@@MatthewWong Hey Matthew, fantastic video, thinking of this DIY. Is the process same for the 320i F30 N20 engine 2013 model?

@MatthewWong 4 года назад

@@tatendak Should be exactly the same!

@bluemax229 5 лет назад

Love the socks with the thongs.

@michaelnikprelaj6679 4 года назад

Might as well just wait when the water pump fails lmfaoo

@joshuamaina846 Месяц назад

Where did you get your 12v charger?

@MatthewWong Месяц назад

Harbor Freight

@davidbutler3159 4 года назад

So I need to actually take the coolant tank out and then drain it as I put oil in it by accident on a very rough and dark night for myself. What steps would be needed to remove and flush the tank itself?

@MatthewWong 4 года назад

Hmm I would look over realoem to see how the tank is held in. I would also check newtis to see if you can find anything on the tank removal: www.newtis.info/tisv2/a/en/f30-328i-lim/repair-manuals/17-cooling/17-00-cooling-check/I4nHM7Ef

@carlosdelacruz3260 4 года назад

Hi ! First of all thanks a lot for the video. Just have one question Before start all process its necessary in the begining disconect the batery? Cheers

@MatthewWong 4 года назад

It shouldn't be necessary to disconnect the battery. You are not dealing with any of the electrical systems that could potentially damage the car.

@MohamedTarek-qm3vf 3 года назад

will this work if i forgot to turn on the low beam ?

@MatthewWong 3 года назад

No just try again. It doesn't take very long to run the flush. I think I did it 5x to be sure lol

@JG-ql7ne 4 года назад

Do u really need to drain the coolant out? Couldn’t u top it off and do the bleed?

@MatthewWong 4 года назад

You could. I just did this to demonstrate how to do a complete flush. Eventually the coolant degrades and it would probably be better to fill it with some fresh coolant.

@JG-ql7ne 4 года назад

Matthew Wong Ight cool thanks for the response bro it means a lot for your insight

@sc225 3 года назад

Yes are yoyusure there is no drain plug on the bottom of the Rad...?

@MatthewWong 3 года назад

I know previous generations of BMW's had a drain plug at the bottom of the rad. For some reason the N20 variations did not receive that at least to my knowledge on the F30 platforms. You can see the official NEWTIS repair steps provided by BMW here: www.newtis.info/tisv2/a/en/f30-328i-lim/repair-manuals/17-cooling/17-00-cooling-check/1VnZAyo8nd they ask to remove the entire coolant hose at the bottom of the rad.

@javy0820 5 лет назад

So according to the instructions you posted TECHNICAL INFORMATION Filling without the vacuum filler device (watering can filling) is not permitted. Non-compliance will result in danger of component damage and/or engine damage. Filling specification absolutely must be adhered to. The operation of the vehicle is not permitted unless the filling procedure has been completed. Otherwise, functional limitations (degradation) and/or overheating may occur. A bleeding procedure is required after a part has been exchanged in the cooling system and/or after refilling the cooling system.

@MatthewWong 5 лет назад

Yep BMW recommends you use a vacuum to make sure you get all the air out. I'm pretty sure they have been recommending this for a while now. But again as I mentioned I am not doing that. Most people who DIY this just flush the coolant out then run the standard bleeding process to get the remainder of the air out. For example even for the transmission flush BMW recommends a pump but it is not necessarily required in my opinion.

@MrPuciek 3 года назад

Looks like the website has been closed any alternatives to that website?

@MatthewWong 3 года назад

So BMW group forced that site to close and opened their own which they charge a subscription fee for :/ I haven't found an alternative

@tommyty6 3 года назад

Driving experience switch must not be in ECO PRO, yours is in ECO PRO😂

@badkid73 5 лет назад

Get yourself a Form-A-Funnel.

@MatthewWong 5 лет назад

I've seen those! I gotta get one and try it out

@dndxander Год назад

does this apply to the 335i

@MatthewWong Год назад

I don't believe the N55 has this issue with timing chain compared to N20.

@dndxander Год назад

@@MatthewWong do you know where to drain the coolan from on my n55

@MatthewWong Год назад

@@dndxander f30.bimmerpost.com/forums/showthread.php?t=1278783 I think this is what you are looking for

@dndxander Год назад

@@MatthewWong quick question man should I loaded bleeder screw when bleeding water and have cap off or have both them on. Please help I did I flush with water but I have foamy stuff in my reservoir!!!

@MatthewWong Год назад

@@dndxander When I did the bleed I only had the screws undone I believe. Its been a while. I am also not sure if its the same on N55 vs N20 (pretty sure its the same but not 100% positive)

@Peter12662 2 года назад

I don't have a battery charger cant I just use my wifes car to jump it while I do the procedure? It should work no?

@MatthewWong 2 года назад

I am not sure entirely if you can, but I don't see why not? I think it's just to prevent the battery from possibly dying during the procedure.

@Peter12662 2 года назад

Thanks. Great video easy to follow. I actually have to change my thermostat. I think jumping it will probably work my battery is like 6 years old so I don't want to chance it

@shamedddy9830 3 года назад

when u said check power steering rack for leaks thats when i decided to leave

@MatthewWong 3 года назад

hahahaha

@anthonyantoine9877 5 лет назад

Flush

@aaronnunez9870 3 года назад

Doing this on my F30 335i. Cannot believe BMW hasn’t just designed a fucking valve go drain it properly. It feels so primitive unplugging the EWater pump hose and lower radiator hose to drain coolant.

@twistedsd 4 года назад

Why was the fluid color so clear at 8:30, was that the distilled water flush?

@MatthewWong 4 года назад

I think my car was previously in Arizona and the previous owner used significantly more water than coolant mixture.

@twistedsd 4 года назад

@@MatthewWong Thanks for the quick reply. I just replaced the thermostat and water pump on my F10 n63, there are videos on here flushing with straight distilled water before refilling with the 50/50. mix. You video Helped me out👍🏾

@MatthewWong 4 года назад

@@twistedsd I think depending on where you are its fine to run distilled water. If you see your temp's start to rise you can mix in a % of coolant and it should help!

@tek2313 5 лет назад

I don't see the bleed part? where are the screws?

@MatthewWong 5 лет назад

I show the screws at 18:44 didn't really record the process of doing it. It is well documented in the newtis documentation: www.newtis.info/tisv2/a/en/f30-328i-lim/repair-manuals/17-cooling/17-00-cooling-check/I4nHM7Ef

@tek2313 5 лет назад

@@MatthewWong I wish you done recorded that part since it's the hardest part. It's really a tricky procedure.