BMW X5 Front Wheel Bearing Replacement DIY (2014-2018 BMW F15X5, F16 X6)

Подписаться 341 тыс.

Просмотров 40 тыс.

50% 1

► A failing BMW X5 wheel bearing will make a lot of tell-tale sounds. A good example of this is a humming sound at highway speeds. Additionally, a bad wheel bearing will also make groaning or clunking sounds while turning. If your BMW's wheel bearings are making this noise we highly recommend immediate replacement.
Fortunately these BMW F15 X5's use a bolt-on style wheel hub & bearing which makes for quick and easy replacement, only needing to remove a few brake components and minimal tools.
Follow along as Gareth Foley, FCP Euro's BMW Catalog Manager walks you through the steps needed to get the job done.
Buy the BMW F15 X5 Front Wheel Bearing Kit On FCP Euro: www.fcpeuro.com/products/bmw-...
Index:
00:00 - Intro & Tools Needed
02:22 - BMW F15 X5 Wheel & Brake Components Removal
04:52 - BMW F15 X5 Axle Removal Process
07:37 - BMW F15 X5 Wheel Hub Removal
12:09 - BMW F15 X5 Prepping for the New Hub
13:28 - BMW F15 X5 Wheel Hub & Axle Install
18:45 - BMW F15 X5 Brake Caliper & Rotor Install
22:06 - Thanks for Watching!
#fcpeuro #bmw #bmwx5
SUBSCRIBE: ru-vid.com?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@vvaskevich 2 года назад

It's exactly the same process as on the X5 e70. Applicable to 2007-2013. Great video.

@TheMetrefekseli 2 года назад

Yes The bearings is the same VKBA 6619

@videomks 5 месяцев назад

I'm doing the front wheel bearing on my e70 X5 2010 and the bolts/bearing are the 12 x1.25 mm. The torque for these bolts is ? 120nm + 90 degrees? Thanks for confirming . All of the FCP videos are great.

@battlehrfred 2 месяца назад

ty Gareth!! Pro job excellent video and tons of great pointers and professional advice!! ty

@gjkMN Месяц назад

For my 2011 x5 50i, the same process but a couple notes: the wheel hub bolts on the original are XZN heads, the kit comes with the t60 Torx heads, so make sure to have XZN sockets on hand. My brake slide pins were a 9mm Allen head, not a 7mm...and ONLY a 9mm will work, so head to NAPA and grab that right ow because it isn't in whatever kit you have on hand. Otherwise, it's the same process. For fitting the new hub onto the axle, you can use some compressed air in a can (aka computer dust) and turn it upside down and freeze the axle spline, shrinking it just enough to make fitment possible.

@mra4107 2 года назад

Very informative video. Could you do a front wheel bearing video on an E83 X3? I understand that it is a more involved process than what you did here.

@baymoe1 2 года назад

Great video

@jessybeatz Год назад

Merci pour ces precieux conseils. Bravo et merci

@jasoneyes01 2 года назад

It's never a bad idea to do a 4 hub changeover at 120000 miles. You realize how much the wheel hubs affect handling, noise, vibration,smooth braking,and safety. X5 is a heavy vehicle with high bearing load, especially with dynamic drive.

@burakozgun1371 Месяц назад

super is working

@garyvanremortel5218 2 года назад

I use Noxudol 700 on hubs to stop the rust.

@TheRafalblog 25 дней назад

Most covered BMW repairs guide on RU-vid I think. I have been looking for this procedure with BMW X3 F25 rear. Have you covered it as well?

@MrMathazi Год назад

Good job man

@fcpeuro Год назад

Thank you for watching!

@bigfwopl4873 2 года назад

lol. we humbly thank you for these. Regarding the rear wheel bears those are a bit of a PITA. Any chance that's coming soon?

@kenbartlett2019 11 месяцев назад

Great video! You mentioned that pulling the axle back through the hub using the axle nut was kind of a no-no. in the past, I've threaded the nut on to the axle and gently pulled the axle through the hub using claws and a slide hammer, and I said gently :-) Why do you think that that's a no-no?

@nigelharris175 2 месяца назад

Is it safe to knock the drive shaft throught???

@joeh606 Год назад

Would you have a video on replacing the motor mount for a 2016 bmw 535i?

@fcpeuro Год назад

Hi Joe, something we could add to our queue for sure!

@6142tellme 2 года назад

My 2015 X5 M has a roar coming from the front driver's side wheel I believe it's the wheel bearing, it's at 50000 miles I'm gonna change it anyway. is this video helpful with the M series X5 2015 15 thank you.

@MrWitchTube Год назад

Rodney, did this help you or was it something else as facing similar sound myself…

@johnronin 2 года назад

My axel will not push back from the hub. I tried pounding it, and using a 3 jaw hub puller but no dice. Am I missing something or is it possible this thing is super rusted on ?

@fcpeuro 2 года назад

it can be admittedly EXTREMELY stubborn, just ensure when pounding it you arent in fact mushrooming the head of the axel, as that will cause it to become a bit more stuck than it may already be(always hit it with the nut still on). IT could certainly be well rusted in there, have you sprayed any penetrant?

@allenzz.3070 Год назад

Please where can buy the wheel bearing puller tool in this video? thanks

@fcpeuro Год назад

Hi Allen, the tool used to pull the axle through is available on FCPEuro.com. It can be found searching CTA-5056.

@davvo87 2 года назад

What Torque Wrench do you recommend for a 420 NM job? Great video!

@fcpeuro 2 года назад

For something with that high of a NM, we always suggest the GearWrench 3/8 drive bean torque wrench. We carry this on our website and can be found by searching GRW-2956N!

@davvo87 2 года назад

@@fcpeuro Hi. The model you suggested only goes to 100NM. Pretty far away from 420....

@user-sc9hw7fc1t 2 года назад

Всем Привет из Москвы!

@dumbeezy5480 2 года назад

@tylertran93nsx Год назад

How do you know when the bearings are bad?

@zildog 10 месяцев назад

Jack your car up and wiggle the wheel north and south. If there is any play/movement at all, the bearings are shot.

@honorablewiz7447 10 месяцев назад

not necessarily....honestly your wheel bearing or hub can go bad and have different symptoms typical you would here some sort of noise to start with. there could be play in the wheel not all the time.. if there is play make sure it coming from the bearing. I have to change mine because the lug bolts hole are stripped causing my wheel not to drive like a bad alignment when turning