Briggs and Stratton 1981 2HP Engine. Will it run? Turning Shop Trash into TREASURE! Repair/Vlog

Подписаться 470 тыс.

Просмотров 222 тыс.

50% 1

Thanks for tuning back into Chickanic! If you found this video helpful, please LIKE, SUBSCRIBE and COMMENT!!
Today we tear down a 1981 Briggs and Stratton 2 HP engine on an Edger that has been sitting for YEARS! Will it run?
If you would like to show your support, find my Amazon Wish List HERE!
www.amazon.com/hz/wishlist/ls...
Want to see the repair I had to do to this brand new Neotec NS 892?
Watch here!!
• NEW "STIHL CLONE" chai...
Buy your own Chickanic T-Shirt or Hoodie HERE!
chickanic.com/
Find some of my favorite tools in the list below!
Get a WERA tool kit like mine HERE!
amzn.to/3CEkWo5
Get your WERA 8mm nut driver HERE!
amzn.to/3I4tx4B
Find your own 2 Cycle adjusting tool kit HERE!!
amzn.to/3IMn4vB
Get a compression tester like mine HERE!
amzn.to/3KM7Ibg
Get a spark tester like mine HERE!
amzn.to/3vIHUbM
Get your own digital tachometer like mine HERE!
amzn.to/3PQgtny
Find your own digital multimeter HERE!
amzn.to/38aX2FJ
Get some 12" hemostats HERE! I LOVE THEM!!
amzn.to/3tMvlvd
Get my FAVORITE pliers HERE!
amzn.to/36P5ud3
Get an Owl Torx drill bit set HERE!
amzn.to/3urvRze
Want a Endoscope like mine? Find it HERE!
amzn.to/3Ni71Ir
Watch my "Best Trimmer Head Ever Made" video HERE!
• The BEST TRIMMER HEAD ...
Get your own Speed Feed Head HERE!!
www.amazon.com/gp/product/B00...
Looking for the BEST 2 Cycle Oil? Find it here!
www.amazon.com/gp/product/B07...
My name is Bre. I took two years of small engine repair at the local college. When I left school, I fell into a wonderful job at a local small engine shop where I worked the counter for a couple years. In 2010 my husband and I opened up our own small engine shop in central Arkansas where I am able to work alongside my family and best friends. We see over 2,000 pieces of small engine equipment every year, and answer 1,000's of small engine questions. We specialize in brands such as Briggs and Stratton, Kohler, Echo and Shindaiwa, but work everyday on MANY other brands like Stihl, Husqvarna, Honda, Craftsman, Remington, Red Max, Troy Bilt, Scag, Bad Boy, Hustler, World Lawn, Poulan, Mantis, Etc.. Hopefully, my experience I share, will save you Time, Money and Frustration in the future!
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting my channel so I can continue to provide you with free content each week!
Although very informative, these videos are for entertainment purposes. Please use all possible safety precautions when repairing and operating your small engine equipment.

Хобби

Опубликовано:

22 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 1 тыс.

@Chickanic 3 месяца назад

Thanks for Watching! Find a link to all of my "Must Have", Favorite Tools HERE!! www.amazon.com/shop/chickanic?ref_=cm_sw_r_cp_ud_aipsfshop_aipsfchickanic_9ERPFPBNGQ924P8NS63B

@thomaswarford2920 Месяц назад

We used to decarbon car engines by running the engine a couple thousand rpm and pooring water down the carburetor. You probably don't want to kill the engine, and I'm sure you don't want to hydro lock it, so careful how much water you poor in there. I'm sure it's harder to do with a one cylinder, but I'd bet it's do able.

@thomaswarford2920 Месяц назад

While you were obviously right, I can't locate where you figured out it was the coil and not the points or condensor. Thank you.

@bradmoyer9737 Год назад

53 kazillion repairs, and you haven’t lost the joy 🤩 of breathing life into old engines and hearing them roar back to life - great to watch, thank you!

@cotydenise Год назад

I'm so glad I found your wonderful channel. As a 62 year old very able woman you make me feel that I can make small and basic repairs myself. Thank You!

@79thPenn Год назад

And she doesn't need to use her sexuality to make a successful channel either. Tis why I often find myself listening to Chickanic's channel.

@jamesvuxta8723 Год назад

All it takes is the will.

@rickkessie1926 Год назад

How do you fix that starter clutch

@butch19471 Год назад

@@rickkessie1926 you can fix some of them if you take it apart and clean all of the grease etc out of it and the squirt some oil into the front of it on the small felt pad. 50 50 chance..

@rickkessie1926 Год назад

@@butch19471 Back in my day lol there was a composite material washer in the cup at the ball bearings very very few knew about this part five digit number started with 69 something

@Muksanim2012 12 дней назад

It's a good feeling when you conquer an old engine.

@Gerrit-Max Год назад

The reason it runs as sweet as a nut after 41 years is because back then things were build to a standard, not a budget. Respect for the work you do and the knowledge you are freely sharing, it helps a lot of people out more than you would think.

@haneyoakie14 Год назад

Amen!

@NONAME-kw3pu Год назад

if ppl just changed oil more than once in its life... at least once a year. drained gas out at end of season. got real gas, not ethanol gas. new air filter every year. things wud last a good long time. now briggs sais "dont need to chance oil, just add oil as needed when it is burned"???? sure why not, planned obsolescence cant sell new motors if they last for a long time with regular oil n air filter changes.

@scdevon Год назад

I like old flat-head Briggs engines as antiques, but I don't know what's so impressive about aluminum cylinder bores and plain crankshaft main bearings. No wonder Chinese Honda clone engines have taken over at the same price point. They all have iron cylinder liners and ball bearing main bearings. Briggs and Tecumseh should have given customers a LITTLE more over the years for NO extra cost. No winder they both went tits-up bankrupt.

@randallcarney1216 Год назад

I have an 1983 horizontal 8 hp off of a Troy-Bilt tiller,

@clecollins2673 Год назад

It still had aluminum liners. I ran a toro with a briggs for near 30 years until the block was worn. Now if one was a true machinist with all the tools, I would bore it and put in a cast sleeve for another 50+ years.

@robertsmith7580 Год назад

It was so cool watching you going through your inventory and finding parts and gaskets that probably don't even exist anymore !

@NONAME-kw3pu Год назад

they exist and for the 2 HP are pretty cheap. even new rod is

@philliphall5198 Год назад

Coils rust up nearly every time and points need clean, usually cond bad

@flatlandriver2471 Год назад

Have a picture from the ‘70s somewhere that shows the mini bike my brother and I built using one of those motors! We weren’t yet teenagers. Welded up a couple of old bicycles and “borrowed” the motor from Dad’s little pencil grain auger. Centrifugal clutch, chain drive. Tiny wheels. We had a blast with it but then our bigger older cousin rode it. Frame broke and nearly neutered him. When we came home from school the next day Dad had put the motor back on the auger and all the welding rods were missing🤷🏻

@charlesmckinley29 Год назад

😂🤣😂 great memories I’m sure

@brianking1138 Год назад

I just picked up one of these for free 2 days ago. Perfect timing.

@philbenton5679 Месяц назад

I get such a kick out of watching your videos. How much joy it brings you to succeed with small engine repair like that Briggs & Stratton. I just grinned from ear to ear at the end of this watching how much happiness you got from fixing that gadget. I've learned a whole heck of a lot watching your videos. Keep up the great work! People all over the world are watching you.

@mdunbar008 Год назад

Person experience with rusty fuel tanks. IF they are still holding fuel, you can drop and hand full of pea gravel in them with a little soapy water and shake the hell out of them to remove almost all of the rust. Rinse well and dry with compressed air. Has worked great for me over the years.

@AESOP2U Год назад

After that, 3m makes a coating that will make your fuel tank bulletproof.

@dougsimpson64 22 дня назад

I took a rusty tank one time and filled it about half full of pea gravel and strapped it to one of those small portable cement mixers and turned it on. Let it run several days and that tank was pristine inside! The downside was that there were some spots where the rust was severe which became. . . holes. . .not a good deal. But, I have used that technique to clean serveral.

@mistersnapon Год назад

Old Briggs engines never die.... I have one from 1948!!!

@stevedittrich4411 Год назад

People often don't understand the feeling of satisfaction that you get when you take a "dead" or trashed engine and get it running again. Your channel is outstanding!!!

@pawsnazzy01 10 дней назад

Back in the mid 60's my uncle had an old reel type mower that had been sitting in the weeds for years, he told me it had gotten hard to start then one day it wouldn't start so he left it there. I took it home and torn in to it. Just like you, I pulled the head and removed the carbon, cleaned & lapped the valves, cleaned the carb, cleaned the fuel tank with a piece of chain and shook the hang out of it & rinsed, pulled the flywheel and sanded it clean & put it together Oh and lubed the hang out of the clutch, and for the first start I put 1 shot of Old Spice after shave in the carb. and it roared to life. No new gaskets were used in the repair just stuck the old ones back in and it worked great. My Uncle used it until the rubber tires worn slap out then my cousin took the motor and put it on a mini bike.

@THEMOWERMEDIC1 Год назад

Busy busy! No rain here has slowed me down quite a bit. Been doing auto repair vids which are doing pretty good!

@Chickanic Год назад

We are still getting equipment in, but have gone into cleaning mode. The shop was a disaster from this season.

@philliphall5198 Год назад

We finally got 2 1/2 inches and I’ve been really busy in West Texas Mostly chain saws

@59Ray Год назад

It was really cool watching you bring the old Briggs back. Brought back memories of my Granddad showing me how to set the coil gap. His “go to” spacer was a post card someone had sent him years before. I remember us using that same post card for years. Thanks for the memories. Thanks & keep up the good videos.

@OcotilloTom Год назад

I'm a 76 year old guy who's been tinkering with old engines since I was 12. I still have a 1949 Cushman motor scooter I have kept alive since I bought it used when I was 14. Also my old Harley's none newer than 1964.

@geraldhix2872 14 дней назад

I remember working on those engines many years ago. That's when it had points and condenser under the flywheel. I've had those engine backfire and the flywheel key would shear just enough to keep the engine from running. Thank you for working on this old engine.

@paulthompson1216 Год назад

Having access to all of those spare parts is totally awesome! Love your videos!

@philliphall5198 Год назад

I would be in Heaven there

@justinsane7128 Год назад

I'm 65 and I recently ran across a little two and a half horse that was the power for my first homemade mini bike, barn find LOL, from 1969

@NSmoosedog Год назад

Great instructional videos you have. However, ain't nobody got all them parts! What a Wife who can fix everything.

@marcheld Год назад

I just love how giddy you get when you’re successful. I laugh right along with you.

@BobbyS1981 Год назад

That Briggs and I are the same age! I’ve worked on B&S engines since I was a child. They are so simple and easy to work on. I’m surprised you didn’t have any old Magnetron conversion kits in that old shop inventory. I installed one on my wife’s grandmothers old tiller that was made in ‘74. Made a huge difference in reliability.

@robinholland9423 10 месяцев назад

I don't convert them, I always use the points and condenser set up, perfectly fine if you know what you are doing

@larryreynolds8580 Год назад

So much better than what we have today. Wouldn't mind more of these. Thank you 😊

@michaelmaker8169 Год назад

How about an extension tube on oil drain? At least temporary. It's alive!!!! Probably more apt to get them running than today model. 👍

@brian_2040 Год назад

OMG, this is the best small engine and outdoor equipment channel going. Great advice and knowledge to be got from here, and the instructor is easy on the eyes, with all the respect. Proven mechanic! Also, let's take a minute to appreciate the amount of inventory this lady has! You dang sure don't see that much anywhere anymore.

@michaelbradford4444 Год назад

One word to describe the feeling when you initially hear a small engine run due to the work you've done ( euphoric!

@justincase2281 Год назад

Now THAT'S a workshop!! 😄 If anyone ever accuses you of not knowing small engine stuff and outdoor power equipment, just show them a picture of that place. It totally screams experience!!👍 I love the other small engine guys on RU-vid, but I think your channel is the best of them all. 😁

@dougbongle3192 Год назад

Simply the best!

@0808dsmith Год назад

Spent a lot of years cutting my parents yard with a 5hp Briggs engine like that one on a Sarlo high wheel mower. Had to tune that thing and change the oil every year come mowing time!

@rustedjunkgarage3316 Год назад

My 2HP B&S on my 1970 California Trimmer Mower still runs like new. My Dad bought the mower new and I still use it.

@wilkersonsmowershop8379 Год назад

Great save! Love those flat heads. So easy to fix and maintain.

@NONAME-kw3pu Год назад

if ppl CHECK THE OIL BEFORE EACH RUN OF THE DAY... and change oil once a year or so. air filter too. the 2HP is cheapest to rebuild, parts a plenty. new rod $9. seals $6. gas tank $$$$$

@ivycycles Год назад

So glad I found your channel. 61 year old lady mechanic here. Into cars too, just like you. Loved watching you fix that old Briggs 🙂

@raymorrison5006 10 месяцев назад

That engine was one of the best that Briggs and Stratton made. I love the old flat heads

@husqv5147 Год назад

What a little sweetheart that 2 hp is. They sure don't make them like that anymore.

@dennisjoiner3717 Год назад

It's tough to kill those old engines! I did a complete tear down and rebuild on one for my 1976 High School Small Engine Class. I miss the fun I had doing that, and can relate to the excitement you had hearing it come to life!

@shannonwhitaker9630 Год назад

We’d leave the Rod loose on purpose to see how long it would take to blow the engines apart at maximum revs ! Shop class was always fun as we always figured out how to do the opposite of what was intended but we learned stuff none the less.

@donmayberryjrsOPE Год назад

@@shannonwhitaker9630 OMG I thought that was just a Jersey thing!! We did the same in 75 when I had already been working for my Dad for 3 or 4 years repairing mowers so the shop teacher had me "run" the class 🤣🤣🤣

@chipcather4042 Год назад

Great video good craftsmanship do you have a antique engine club in your area.

@RobiBrown-eb8lo Год назад

Used to race go carts in the late eighties to mid nineties. We had a blast. Ran stock class at Rockingham for years and Charlotte a few times. Kick the rod out and Sunday epoxy the hole and new rod and ready to go. Blast!!

@jayztools4038 Год назад

Love the paper plate bag funnel thing!!! The easiest mess to clean is the one not made!

@gretalaube91 10 месяцев назад

Dang! I coveted those horizontal shaft engines when I was a kid! Go-cart! That was 50 years ago. I still covet them, and have an old washing machine one downstairs in the garage. My wife's like: get rid of that! No way! None of my daughters or sons had any interest in engines, so you are great!

@philliphall5198 Год назад

1981 was just yesterday to me and it was the greatest time with kids and softball

@dubbssawshop Год назад

That’s one of my favorite things to do, dive in the junk pile and find something to make work. 👍👍

@NONAME-kw3pu Год назад

it wasnt junk, or it wud have had a BIG LIP at the top of cyl, scoring from running it low/out of oil and no air filter. those are... i rebuld them to see if i can get them running, they run with 20-50 oil and lots of STP oil treatment 30%? but vicious piston slap... rod knock if i cheap out and dont spend the little extra $ on new rod as the alum rod wears more than the steel crankshaft . drill out the oil hole on the big end of the rod for MORE OIL to the rod journal so it lasts as long as possible with fresh oil

@gcampbell83 Год назад

I am so jealous. I wish I had a parts department like yours at my house. I loved how you saw what part you needed and went and found the forty year old part right there in your inventory. Congrats on getting the old motor purrring again! I enjoyed and liked your success.I knew you could do it. Super good job!

@bradleycallahan6169 Год назад

Thanks for the memories. As a teenager during the 1960s I mowed our lawn (almost a acre) with a reel mower powered by a Briggs and Stratton engine. I was always adjusting something and not always well.

@NobodyWhatsoever Год назад

1981!! It reminds me of growing up. My dad bought, I believe, two push mowers while I was a kid. At least he shopped for one twice. He really needed a riding mower, if not self-propelled, for the size of the lot my parents' house was on! Anyway, he swore by Briggs, and insisted he'd never get a lawn mower with less than 5HP. The last mower he bought had the large wheels in back, which helped a lot in the soft wet earth where we lived. Do you still see such old equipment on occasion? And ... am I mistaken in thinking lawn mowers used to commonly be two-cycle, or have they been largely four-cycle engines for that long? Wait, wait, wait. We're both 80 babies?! Ha! I learned a coworker and I are just a few days apart in age.

@mdunbar008 Год назад

Such a great video, brings back memories of working on those old "L" heads when I was a kid. Just looked at my old Briggs manual that I purchased NEW, it was printed March 1984. Love watching your videos, even though I've been rebuilding small engines for over 40 years, I still learn stuff from you.

@mickeybailey5147 Год назад

Clean the small end of the crankshaft and lightly oil. There is a felt sick in the square part of the clutch to hold and distribute oil. IF the clutch slips, not engaging, remove two screws and pry off the top clutch cover.. clean the ball bearings and track. DO NOT oil or grease them or they will stick to the far ends. This was state of the art when I started teaching in 1982.

@Jeffrich308 Год назад

The fact that you did that in white shorts and didn't destroy them is amazing! I walk near mowers and my clothes are dirty.... Thanks for the video, that old motor brings back memories from my youth.

@jcondon1 Год назад

Very nice. The $100 5hp tanks also look terrible. Those engines will run forever if you take care of the tank.

@garyalensr Год назад

Hey James good morning. Love your channel

@garydillon3960 Год назад

You sure brought back some great memories with that 2 H.P. engine repair. Thanks for the memories.

@edwincolonperez1231 Год назад

I had faith in your ability to get it running GREAT JOB

@TgWags69 Год назад

A trick for the throttle cables, find some cheap vinyl tubing that will fit over the end and run it up as far as you can. Use an electric vacuum pump meant for brake bleeding that uses a reservoir (or make one out of a jar with some tubing) and oil the top of the cable. the vacuum pump will pull the oil down trough the cable and oil it all up good. even if you can't get the tubing up very far, you can just oil up the housing pretty heavy and it will pull the oil through the gaps. This works well for modern cables with the plastic housings as well, just tape up the end of the tubing to the vacuum is being pulled through the housing. Hope that helps....pretty easy if you are set up for vacuum bleeding brakes already

@NSNorfolk Год назад

I had EXACTLY that engine on my mini-bike, circa 1963-64. Great job on the valves and seats. BRAVO!

@tjclarke4604 Год назад

How were the valve guides on this engine? Back in the early 90's we still used to use a valve guide reamer (or drill) and tap new sintered bronze valve guides in. I haven't done that process in over 20 years, it's just not worth it anymore, but there was a time. Just curious if the valves in your engine were floppy at all of if the guides were still tight. EDIT: Just something cool that you might be interested in, for the mess free oil drain, what I did was drill a hole through an old oil plug and put a piece of clear hose over the square part. Then pop out the real oil plug and install you new tool hose/plug, and let 'er drain. Works like a charm. Also, I knew that starter clutch would wail like a banshee. You can actually service the clutch, not necessary to replace it. Unscrew it and polish the crankshaft end with sandpaper, the clutch comes apart, and you can drop some oil on the ball bearings. OR, if you want to cheat a bit, that little hole at the front the of starter clutch is there to take a squirt of lube. I have been an outdoor power equipment technician for almost 30 years, I love your videos, there aren't many of us OPE techs left out there.

@georgepruitt637 Год назад

You're correct! not too many of us left.

@mikejerrett7354 Год назад

I said it before I love all your videos but these trash to treasure videos are so fun to watch. That thing ran awesome 👌.

@Chickanic Год назад

Thanks again Mike!

@randyberger4910 Год назад

This reminds me of working on a Brigbs 5 HP on a garden tractor my dad built in 1964. I cleaned out mouse nest from cowl, took off head saw valves worked, spun the crank shaft with the rope and it was good. Put in some fuel and it started. I needed a gasket for fuel tank. The tractor had a transaxle from a Crosley car, various gears from things and a steering wheel and box off an old C tractor. Attachements were a generator and weed mower from a Bachtold walkink behind mower. The Briggs was the only thing he bought new after the Wisconsin engine never did want to start. Thanks for the memories!

@frankwrogg2515 Год назад

Lots of memories from the 60s and 70s when as a kid worked on these.

@melvinlewallen7796 Год назад

Love your videos please don’t stop , you explain well and makes sense and 99 percent of time can follow your own repairs have fixed 4-5 pieces of eq

@matttravers5764 Год назад

Love your vids Bree! Just have to say, that original starter clutch just needed a squirt of oil on the crank snout. Also, makes me feel old that old that a 1981 engine is viewed as an antique these days. I graduated from high school that year. Was playing with these old Briggs engines back then too as a hobby. Would like to see more of you working on the older stuff 👍😎

@collectingonthecheap56353 Год назад

That old logo brings back memories of when I use to tinker with Briggs and Stratton lawnmowers.

@ricksrealpitbbq 10 месяцев назад

This video brought back so many memories for me. As a kid in the 60’s I’d go to the junk yard and get those engines to build homemade mini bikes and go karts. I’ve rebuilt so many of those engines. So much fun to work on them.

@paulmcreynolds1774 Год назад

Great video. I really love these trash to treasure videos. You need to do more of them. I love your channel and look forward to new videos. Keep up the great work

@robertmailhos8159 Год назад

Nice looking edger there a 1981 Briggs and Stratton engine just thinking if it has points and condenser ignition system

@jeffpiatt3879 Год назад

As a kid, I fixed up a few different old mowers for neighbors and to make money mowing yards. I really like the old white color briggs from the 60's and 70's. They started painting them black in the mid 80's. Also, old mowers from that era used to have the cylinder facing the back of the mower instead of the front. If you pushed down on the mower to let it engine recover in tall grass you would get smoke out of the exhaust from the cylinder getting flooded with oil.

@mjb12141963 11 месяцев назад

I love those type of edgers. When I was a teen back in the 70s, I got to use one at my Grandfather's house. I wish I had enough sidewalk and driveway to justify buying one.

@rogerwilson500 Год назад

Great video. My Daddy worked at Jacobsen Manufacturing for 30 years and left several old Briggs horizontal shaft motors in his shop. You’ve inspired me to get em out and see if I can get em going!

@donmayberryjrsOPE Год назад

Hey Roger my Dad sold Jacobsen back in the day, mostly tractors. Some are still mowing the lawn! Let me know if you ever want to move those old engines or have someone (like me with almost 50 years experience) get them working again!

@markschommer7407 Год назад

@@donmayberryjrsOPE I have one of the old 2-cycle Jacobson lawnmowers from about 1960. Got the 4 blade disk setup. It does still run, but needs a restoration.

@donmayberryjrsOPE Год назад

@@markschommer7407 I remember working on those units mostly in the 70's, they were pretty popular then. Sharping those 4 blades was at challenge and generally we just replaced them. Where are you located?

@markschommer7407 Год назад

@@donmayberryjrsOPE Appleton Wisconsin

@rogerwilson500 Год назад

@@donmayberryjrsOPE I will. I really ain’t got no use for them. I just had another hip replacement last week. When I get better I’ll go over to his old shop (it’s mine now) and see what all is over there. As far as I’m concerned you can have them. I’m way behind now on my sawmilling so I don’t have time to fool with them.

@Corvette1658 Год назад

You can never out beat those old vintage Briggs motors.

@jayalbertz9756 2 месяца назад

What a coincidence, just stumbled across this video today and earlier I was working on my dad's old rotor tiller that hadn't ran in years. Fresh gas, new oil and the 5 horse version fired right up!

@rlatall1 Месяц назад

I restored a steel gas tank on a B&S tiller by removing the tank. Then I filled it about 1/2 full of roofing nails, some acetone, taped off the openings, then I shook, and shook, and shook!!. When I was finished the tank was shiney smooth inside.

@gearheadgregwi Год назад

Finally, a flathead Briggs & Scrap 'em!! Near to my heart. Subscription from land of B&S. The balmy state of Wisconsin!!

@raulsanchez4493 Месяц назад

OMG just had a flash back! My dad had the same edger back in the 70’s

@Digidoc316 Месяц назад

Boy, does that engine take me back! Had a tiller with one just like it! Saw another feela use a Scochbrite pad, some WD40, and a drill to clean up the valves; seemed pretty quick. If I remember right, I had to use a 3/8" open end for tightening the carb bolts. To avoid future messes, thread a 1/4 turn ball valve and a 3-4" nipple into the drain plug hole. When time to change comes, pan it and turn the valve. Those things were the Timex of small engines!

@donmayberryjrsOPE Год назад

Chickanic the clutch starter removal wrench is Briggs part number 19244 and you should have one, lol. Cool video! But you should have replaced the points and condenser, those engines weren't that simple when you had to do a complete service on 10 or 15 a day in the 70s!

@walterbordett2023 Год назад

I have a 1978 Sears compact tiller with that same engine on it. It gets used once or twice a year or so. Always starts and runs great. The tiller cost $135.00 in 1978. Thanks for the fun video.

@trekOCLVone Год назад

I can relate to the old school B&S engines. Brings back memories of that old tech with all metal parts and points. Thanks for sharing.

@old-n-still-runnin1597 Год назад

Wow! Took me back to the old days. We used those little Briggs for go-carts, mini-bikes, and phut-phut mud boats. You can grind the valve stems down a little so the valves close more to top dead center, kick up the compression and the torque up on those little jewels. I am really enjoying your post. Keep 'em going!

@ancietman Год назад

My dad bought a brand new cultivater in 1964 with a Briggs & Stratton engine he used the machine in the garden & he had a four acre field it was in use constantly the machine was still working up until his death in the mid 90s & I was using it until about 5 yrs ago. At present its in my shed but I expect if I got it out & dusted it off it would still start. Amazing engines & its cost very little to maintain all that time.

@K0Kaz 2 месяца назад

I realize this is an old video, but this brings back memories. We DO have sidewalks out here, and it's been a LONG time since I've heard the telltale sound of edger blades on concrete. And the one of my major shop class projects in high school in the late 80s was rebuilding a B&S, probably a lot like this one so it's nostalgic all the way around.

@davidparker8242 Год назад

I just found this channel and I love it! I love seeing women being awesome at skills we traditionally associate with men. And I am learning from each video!

@chadcheeseman3871 Год назад

That old engine will outlast anything built today! It's such a shame small engines aren't built like that anymore. Now its a throw away society. Great job getting it running!

@burlingtonbill1 Месяц назад

LOVE the sound of those old Briggs flatheads! That's the sound I grew up with !!! That "2 horsepower" is prolly worth double its rating in comparison with modern Briggs engines!

@allenu6295 Год назад

I use to rebuild these when I was like 9 years old and put on go carts

@dupchurch105 10 дней назад

Great video. I have edged a lot of curbs and sidewalks with an edger just like that one. There is nothing better and they were nearly indestructible.

@michaelprior1097 Год назад

This video is bringing back memories from my time at the company Little Wonder when we assembled the edgers a long with the trimmers.

@scottyellis3442 Год назад

Loved the video, back in the mid 70's I had a push lawnmower with a 3 horse power engine & this reminded me of my childhood.

@robbrie 11 месяцев назад

Wow, now I remember the B&S Snapper mower on which my older sister taught me how to cut grass had a metal gas tank with a metal gas cap...circa 1981.

@oldredcoonhound2182 Год назад

I have one of those engines sitting in my shed, many years ago was thinking of using it for a go cart.

@laurencemiltonbell6951 Год назад

I restore these old Briggs for therapy reasons because it sure isn't for the money. I currently have a '81 2 hp Briggs on the bench off of a Mclane edger with a '63 Montgomery Ward edger, also a 2 hp Briggs, waiting up next. There's a beauty in the simplicity of these engines and they go forever.

@janchristensen7993 Год назад

Will it RUN ? That’s an understatement

@dsdragoon Год назад

That was a great project. About 52 years ago I bought a new Edger just to get the Briggs and Stratton engine for my first go-cart and I put an electric motor on the Edger. It was cheaper to buy the new Edger than it was to buy anew Briggs and Stratton engine.

@angieshaw8877 7 месяцев назад

My hubby found an edger similar to yours at a local pawn shop ...he is retired from more high-tech stuff on commercial aircraft, but he really enjoys and appreciates your videos...it seems to be very therputic for him...he just wants to return small air-cooled powered equipment just for our home use... Bre, you are a real God-send blessing😂 to us and others...Jesus knows how to bless you...just ask Him and believe!!❤😂

@stevedimartino683 5 месяцев назад

You are so awesome and so much entertaining, I enjoy your shows. 👍👏👏👏

@badbob Год назад

In the late 60s I had a mini bike with a Briggs engine very similar to that one. Brought back memories. Enjoyed watching that one as I do all of your vids. I all ways learn something new. Tnx.

@Soggstermainia Месяц назад

Just an idea, when working on the top end, cut a spare air filter sponge to the size of the piston, aka make a disc of foam. Use a cable tie, poke it through, then an inch over feed it back and lock it. You now have a sponge plug to stop junk getting to the rings, get it wet with motor oil and pop it in. Protects the junk falling down, scratching and damaging things, but is easy to remove. Bonus it lubes the walls as you pull it out before you pop a new head gasket on and seal it up. Not seen a 2hp brigs that old before either, cool stuff!

@williampennington5307 Год назад

Use to have 3 of those little two horse power Briggs wish had them back good to see the little fella come back to life

@thecannabiskidfortier6219 Год назад

Had a 2 HP Briggs on my first go cart then 2 years later my stepdad put a 5hp Briggs. The 5 HP block was patched with JB weld cause It had a hole in it. My stepdad was a small engine mechanic for many years but he decided to drive a transport truck as a profession.

@deweythompson5279 2 месяца назад

I started out on these type engines. I added a threaded pipe with an elbow and then a plug so i could drain my oil easily. I also had an old "church key" i bent to a 90° angle to make it easy to get to the bottom bolt on the Carburetor. I really enjoy watching your videos!

@ridgeschneider6485 Год назад

I had one of these! Was given it while I was in middle schoole by my dad who wanted me to learn about engines. Fixed it up, and I’m fairly certain he still has it!

@alanrowlands-xw5zm 2 месяца назад

Only recently came accross your videos due to being laid uop with minor health matter. Have enjoyed quite a lot this past week & learnt plenty. My dad had an edger identical to this but we couldn't get it repaired due to lack of parts according to the mechanic. I have a few aging small motor pieces requiring some attention but not worth spending money for the repair shop at about $80 an hour. All were working recently so I am going to see how I go fixing them. Will probably have my tablet in the workshop to refer to your vids when necessary. Can't find anything about the small shields in the carburettas or where to puchase some though. Thanks for your vids. I think you are very clever. I'm 73 now so this gives me another interest - I recently taught myself to service sewing machines for my wife and daughter's charity sewing group. New interests for an ex banker. best wishes.

@burlingtonbill1 Месяц назад

AMAZED that you kept the filthy black old crankcase oil off those brilliantly-WHITE jeans you're wearimg !!!

@lob4984 11 месяцев назад

I used many of those edges. Been mowing yards professionally since 1980. The mowers of today are sooooo much superior than that old technology

@jimbrewer2893 Год назад

YEAH!!! Makes one feel real good to bring an old motor back to life.

@joeolejar Год назад

My same vintage tiller has the same engine, tank and carb . Put a solid state ignition coil on it 15 years ago. Still starts on the second pull. Yours even sounds the same. Good deal!

@kellykaiser6446 Месяц назад

My experiences with at least 3 or 4 Briggs & Stratton engines that were anywhere from 10 to 30 plus years old, was that if the carb and tank aren’t destroyed, they will run and run well! Even if they are Smokin!