Building The Simple Tricopter from www.simplecopter.com

Подписаться 7 тыс.

Просмотров 260 тыс.

50% 1

Check out my web site at www.Simplecopter.com
Here is a list of the current parts i am using for my builds. this may be different than the parts used on this build video. i am always trying to improve as we all should.
you will need to copy and paste some of the links. sorry
ESC’s (electric speed controller)
www.buddyrc.com...
Control board KK2.1
www.buddyrc.com...
3.5mm bullets
1 pack to connect the esc’s to the motors for crash break away. Buddyrc also has them
(For Vtail)
www.simplecopte...
for Tri and T copter)
www.simplecopte...
Props
Buddyrc USA based
counter clockwise
www.buddyrc.com...
clockwise
www.buddyrc.com...
10x5 use with 1400kv on 3 cell only or 980kv on 3 or 4 cell ( these are more efficient but not as snappy for aerobatics. They are very good in the wind)
www.buddyrc.com...
Motors
High end (at least for me) sorry these are hard to get. I have made these very popular.
Sunnysky 2212 1400kv use 8x4.5 prop on 3 or 4 cell or 10x5 on 3 cell.
USA dealer when he has them www.buddyrc.com...
Ebay also has them
www.ebay.com/it...
Sunnysky 2212 980kv use 10x5 with 4 cell pack. These give 10 to 15% more flight time with slightly reduced power. They have enough power to fly on 3 cell but if loaded with fpv gear then use 4 cell.
www.buddyrc.com...
servo if you need (not needed for the Vtail)
Cheap servo if you are on a budget
www.hobbyking.c...
More heavy duty servo
Hitec HS82MG
www.servocity.c...
KK2 control board vibration pads
www.simplecopte...
Motor and servo pads
www.simplecopte...
zip ties
www.simplecopte...
www.simplecopte...
5 Male to male servo connectors to hook receiver to board
www.simplecopte...
for Vtail you will need 1 foot of red and black 14 gauge wire and 9 feet of 18 gauge wire for esc extension. For tri and t copter the same but 7 feet of 18 gauge is fine.
As far as batteries go i like the hobbyking compact zippy.
And the Glacier batteries from Buddyrc
buddyrc.com
Building The Simple Tricopter from www.simplecopter.com

Опубликовано:

2 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 297

@ThePwnageHobo 10 лет назад

It's probably worth mentioning that this frame is a David Windestål (of FliteTest) design.

@ThePwnageHobo 10 лет назад

Or at least the centre hub of the frame.

@RCShufty 10 лет назад

Everyone pretty much knowns that these days dont they?

@hallstudio 10 лет назад

the frame in this video is an enlarged version of Davids frame with my own simple yaw design. the frame i sell is different then the one in this video. I should have given David credit as we all should for cumming up with this great layout. The guy kept me in the hobby and i owe him allot. I got a chance to meet him at SEFF and we had a good time.

@ROYVAN2006 6 лет назад

огромная эрекция The best quote in history is "Keep it simple stupid".

@RiccoStarrz 10 лет назад

im trying to do the pass thru for throttle it works while buttons are pressed down once i release the passthru fails and i cant get any response

@KillaKlownFPV831 10 лет назад

I REALLY need your help. I built one up w OPTO escs and all seems to power up but ONLY when UBEC is wired straight to my orangerx which powers up the kk board but NO servo movement at all UNLESS i hook up a 6.6v Receiver lipo to the M5 input, if i just wire the 5v UBEC to that input NOTHING POWERS UP

@slugkille4181 10 лет назад

This dude can fly!

@GhoolerHunter 10 лет назад

I want to build something usable for FPV and video work that is inexpensive. Everyone seems to have their own ideas but so far I like this one the best. I have a Blade 350QX that goes crazy on me sometimes even with the shielding around the camera. Horizon Hobby should recall all these because they advertised it as being GoPro compatible and it isn't. It's clear the 350QX isn't going to do what I want to do. Besides I would like to understand how to build one, fix or modify to do what I want to do.

@Jubi316 10 лет назад

How much does it cost to build this and what is a good controller and price . Thanks

@harrybrotherton5108 10 лет назад

When I power up my kk2.1 board it doesn't show the voltage of the battery and non of my inputs actually do anything .. Help?

@OutbackKanga 10 лет назад

Great Video , very helpfull & Love your Accent .. you sound like Tommy Lee Jones :)

@joehandsome99 9 лет назад

Very useful video. I just bumped up my stick settings a little which was very easy to do following your video. Just did a test flight and liking the new settings. Thanks!

@JHolm-df2dc 10 лет назад

Hey Matt! Thanks for the video. Very informational, very complete. Keep it up!

@gfdfperte4248 9 лет назад

What are your flight times with the 4c battery, what is your AUW What mhh battery are you using. Thanks and great video love your honest work. I just bought a Yuneec Q-500 but want a Tricopter to have fun with. The Q is great for Pictures and Video but not for FUN. CFI

@bz7427 8 лет назад

In this video it show you hooking the power up to the kk board from power leads going to the ESC. I was wanting to know what the volts is going to board from the batteries??? 7.4v/11.1v???

@MrWildfire78 9 лет назад

thanks bro thats a very nice tutorial im building one if i have problem hope you can help me....nice bro two thumbs up

@GeorgeBonez 11 лет назад

Dude you are the sickest-ass T-Cop pilot I have ever seen in my life! I have been researching multi-ro vids for 6 freakin months and I just happened upon your vids today and I am in freakin awe at your skill level! YOU SMOKE EVERYBODY ON youtube that I have seen and thats a lot. I have sub'ed and now I am going to hit your site. Even your KK2 tutorial is the best I have ever seen on this FC. Dude you just WOW'ed the shit out of me! Thanks for the great vids k and get ready for a bunch-O-?'s! :)

@bdanieltube 10 лет назад

Great video man. Thanks. I got my tricopter all built and after doing the basic setup i tried flying, it kept going to one side, so i stopped. What can it be? Also im still using the 1.2 firmware on my kk2 board, can i fly stable with that version? Because i cant get my hands on a usb flasher thing right now. Thanks

@GeorgeBonez 11 лет назад

Tri-cop pilots are crazy-asses! Haha and Hall is a perfect example!

@roshanhegde7645 7 лет назад

plz help me!!..i am making a quadcopter with 1400kv motors and a kk2.1.5 board and a flysky Ct6b transmitter...i am done building the quad but after when i arm it, all the rotor start to rotate at different times and after i take the throttle to the middle the kk board just restarts and show the version name and then the safe screen plz help me....could it be a battery issue?

@GeorgeBonez 11 лет назад

Any chance that you are from North Carolina? Just asking because your accent is just like mine and I thought that I recognized some of the landscape from one of your other vids? Hell I know that it all looks alike once you're up high but one your vids look extra familiar! Lol

@AGEN7HIT 11 лет назад

We asked for info setup on kk2 board .. And we get a hour long video ... All our questions are answered .. "All hail HallStudio" now can we have a close up on your stick movement when your doing your flips, rolls, summersaults ,.. Or is that close guarded secret ..

@geo_cash 10 лет назад

Hi hallstudio. I could be completely making some rookie mistake, but could you please explain how to power the kk2.1.5 board. What kind of connector am i supposed to use or is it powered through the esc's?

@Da1nonly44 10 лет назад

Hi, just saw ur video,very nice. I was just wondering can you build me one of these cool machines,and everything you need to fly. How much would it cost for everything you need, including the remote? Just a rough estimate of how much you think will cost to build one. Thank you.

@MilanKarakas 10 лет назад

Excellent tutorial, easy to follow. I like tricopters more than quad and other copters - it behave more like airplanes, except less sensitive to the wind which bouncing plane arround. I have plan for the future: thicopter, delta wing, and collective pitch 3D/4D parkflyers (similar like 'normal' plane, but with props acting more like helicopters). Your video is an inspiration to me. Thank you for posting it. Cheers.

@kandisland 9 лет назад

Hi Chuck. Your videos are really awesome. If someone wants to purchase one already made how do they do that? I know there's a lot of different models and prices, but can you give a range on what they cost if they're prebuilt? Thanks

@MrLazer1211 10 лет назад

@RP- Yes and no, you can build a quad without the KK2, but not a simple one, the reason for using the KK2 board in almost every single multiroater build is because it has all the gyros and goodies built in, you can use a normal board, but you will have to edit it using your computer, with the KK2 you can edit right there on the board with no need to hook it up. And an every day flight board will require external gyros to be hooked up to it ultimately adding more weight and complexity to the multiroter setup.

@iitra 10 лет назад

Mate thank you thank you thank you That was the most informative video I've watched on all this ever that helped so much it will get me flying ASAP Nice simple explanation two thumbs up

@gfdfperte4248 9 лет назад

Also I think I am going to try the CC3D open source board. And on the Servo I am just not sure on the Digital vs the Analog I do not know the correct one to get. What way does the Tail servo have to travel say to rotate the tri CW I might have missed that part of the video. So if i am in back of the Tri. and want the Tri to rotate clock wise does the serve tilt right or left. Keep flying and what a nice Tri CFI

@LandersWorkshop 9 лет назад

Good video, don't ad request at the end though mate, you can lose your account for that.

@gerterwt11 11 лет назад

love youre vids man! i ve tried to buikd 2 quadcopters without any good results. result is that i have 2 with 3 good motors on it so best thing to do seems to build me a tri copter also. and servo's i have enough.... metal geared analog and digital. if i have any questions can i ask you for advise? oh i dont have the kk 2 but the blue v3 control board is that a problem? greets from Holland

@alexecheverria 11 лет назад

Figured out, current comes from ESCs data-V-ground cables. Then current goes from board to receiver... I use a X9 and it is different, no names only channel numbers. I have a quad so calibration is different. But thanks for the binding auto level calibration tutorial for KK2. I wonder what you press in transmitter to disable level...

@alexecheverria 11 лет назад

Is the board connected to battery? Does the receiver have cable to battery? I missed that part or I dont find it. Please tell me how those two boards receive electricity to work and how many volts. As I see you are using a 16V lipo and receiver and controller need around 5V I am not able to figure it out. Thanks.

@fredlaborete 9 лет назад

how to increase the Flying Time.....say 30 minutes. Add battery capacity? Is it correct?

@jordanrsorg 10 лет назад

Hey alls, I'm getting together all the parts for this tricopter build but I'm a little lost on which radio I should get. Looking for receiver and transmitter. Also looking for a source to find the right battery. Thanks for the help, links would be great. Cheers!

@ROYVAN2006 6 лет назад

get the best you can afford.

@argitos77 9 лет назад

question..... ever play with apm boards... I have built a pentacopter... rear center is on a pivot... front center left open for fpv and video I cant find any info on using the apm 2.6 setup for a pentacopter

@HobbyKing1000 11 лет назад

what is the black and red wire coming out of the top right of the board I have my tricopter put together with your instructions but my board didn't come with those wires, and I cant get it to bind correctly, please respond its urgent.

@DaIgnasSme 10 лет назад

Hi, i want to try making one for myself and i wanted to ask what are the dimensions of tails, that cube at the driving tail? Also, approximately, how much does it cost to make one?

@JeremyGlassRealtor 11 лет назад

Can you put a detailed parts list in the description of everything you need so I know exactly what to order? I am just starting out and would thank you so much for all you have done for this community!

@dave_s_vids 10 лет назад

Excellent video, thanks! I'm now considering a tri-copter over a quad!

@davereap 10 лет назад

I take back the comment on esc calibration as with the newer firmware there is a long enough time gap which lets you get to those buttons ok

@mubarikmorojehoney5625 9 лет назад

Am trying to calibrate my tricopter And is not working. I used PS fly sky transmitter and a receiver. I want you to help me

@RockyMountainRc 11 лет назад

Can you do a video on how to do flips? I dont understand if you kill the throttle while it is in the flip or if you let go of the the throttle. Also, what run times are you getting?

@donbrideau 10 лет назад

Thank you very much for making this video. really amazing flying with this kit.

@hallstudio 11 лет назад

dont know they came on the esc's and i did not take them off. they are Ferrite rings and have somthing to do with interference

@cesar68033 11 лет назад

Your the Man U cleared up so much for me next I will buy the same motor u have and could I use the sunnysky 1400 kv with the hobbyking 18-20esu from ur cheap tri video

@Poulpc 11 лет назад

really nice video, small tip: you are breaking your youtube partner contract by encouraging people to watch your ad`s

@erbysgsxr 9 лет назад

hey i have a question about your video , i noticed while hooking up your kk2 board there are a set of wires red/black on the right side of the board towards the top of the board. im wondering what these wires go to ?

@hallstudio 11 лет назад

got a couple of the 15amps for a small tri and they were unflashed. worked about the same as the plush. not bad.

@khateeburrehmannazar845 8 лет назад

very useful. but i want to learn about the circuit and remount control systems of small helicopter. would you please explain it for me??

@MrLazer1211 10 лет назад

To fix the "Wire stress" on the motors you can simply take some quick set epoxy and cover where the wires are hooked to the motor with it. It will remove all the moment of the connections.

@walkeranewbie 11 лет назад

got mine going last night matt, whooo hooo ! this thing is more stable than a beginners 3 channel. it is also super fast. a dream come true.

@starrvalley12 10 лет назад

At the end of the video you changed your settings on the board to your fast settings was still with the version 1.5 ?

@hallstudio 11 лет назад

good idea, i can call it the simple Borg Drone. "Resistance is futile....you will be assimilated"

@TimJC513 11 лет назад

What are the length of your arms from motor shaft to the center of the board? What size props are you running as well?

@rp4489 10 лет назад

Can you build a simple quad copter with out have to use a fancy KK2 board.

@jameskeough4620 6 лет назад

O.K., the first two links for parts don't work. 404 error. Please advise.

@kools8k 11 лет назад

Hi, I have watched this build quite a few times particularly with regards to the controller board setup.I have done everything correctly including checking that all motors and servo work with the Corona Rx (Futaba 6E) Problem: I show no voltage on the opening screen. There is a place in your vid where you say something like 'if I now hook this up and my cable is long enough I should get voltage'. What did you hook up as I assume that you were programming the board with the battery connected? thx

@chrisleech1565 11 лет назад

First choice by default... Redbrick 30A ESC's that may not flash. And they are slow off the shelf. So your choice of ESC is important for sure and should be considered and researched. I ordered these cause the much praised Turnigy Plush 30A were BO'd and I didn't know any better at the time. And little did I realize that they were beginning to ship the Redbrick 30's with the reset circuit of the MCU (Micro Controller) disabled so that they may not be flashed. Rather counter productive.

@dibrin1979 11 лет назад

Every tiem i give just a little throttle it wants to flip over on its top Ive had mine together with the kk2 board runnin 1.5 but i cant get the damn thing to lift. Motors are in the correct m slot and all running CCW (same props all around). Its just one side seems to want to give more power than to the other. IDK maybe its a bad transmitter. Im just really at a loss. I cant seem to get it to run like yers. sad day 2 weekends gone unable to fly. :(

@chrisleech1565 11 лет назад

I do have one lingering question though Matt,In the "motor lay out menu" and you pick Tricopter, does the KK2.0 board do the Clockwise motor reversal for front left and rear motors (as I am assuming the default rotation is C.C.W.) And then all you have to do is put the correct type of prop on each outrunner, or is there some other way to do this that I haven't yet conceived of? This is the 3rd time I have come back for a look while I wait on parts and talk it up on forums,

@martinweyer7732 11 лет назад

airplane (acromode) vs heli mode Good Question. different terms, for the different modes. lots of pages turned to refer to which is which ie dx6I. A rep fromHK, did a tutorial on KK2 set up and he mentioned 'go with' airplane mode . You said you got a decent hover.in airplane 'acro' mode. MHall, didn,t mention either mode, and I don.t think the guys @ Flite Test did either. will go into my KK2 Ver 1.2, change settings, I might as well change it to Heli mode terminology mite be easier

@debeumers 11 лет назад

First off all thanks Matt for the great video you made on assembling the tricopter. Your video was a big help. I made the frame myself, with a dremel, (I'm from the Netherlands, you don't ship there) and it worked perfectly. The tricopter is flying great. I have to get some more skill in flying but that will come in time. I have only one question. The outermost tie-wraps on the motors, break at the slightest bump. Do you use a special kind of tie-wraps? Or is there something i'm missing?

@ammosal 11 лет назад

Hi there.help needed please!!!! I have buildt my own tricopter and is using a kk 2 board and 18a turnighy ecs and dt750 motors.i am using a a spectrum dx6i dsmx transmitter and is struggling to find any info on how to set up the dx6i and what particular settings it needs to be at.when I throttle up the tri up there seems to be more power on motor no1.so I don't know if it is settings on my dx6i.i am new to the world of rc and any help will be greatly appreciated.

@micha0001 9 лет назад

Did you already caught the guy who stole your tripod and mic?

@LateNightWithGray 11 лет назад

The rudder setting on Channel 4 is due to having the servo positioned reversed. It isn't to do with analog versus digital, although that's a good guess. You can either set it to -100 as you did, or just switch your servo to channel 5, which in Tricopter configuration is the rudder channel (4) reversed.

@ZeroGravityUAV 11 лет назад

For anyone thinking of purchasing a tri or t-copter from Simplecopter(dot)com I can not say enough how impressed I am with these products. If you are getting into multi-rotor aircraft, this is where you need start. Excellent product. I made the order and two days later it was at my door. Very impressed with this little craft!!

@chrisleech1565 11 лет назад

Following your good work, got the parts coming for a tri with my own frame design. Wanted to know where the battery voltage input leads are soldered. I can't determine by looking at an enlarged picture of the back of the board where these "pads" are. All the best for your upcoming uploads from your neighbor to the north.

@Cyberdactyl 11 лет назад

Thanks for the tutorial. But I must say, I can't believe you're selling these without even mentioning David Windestal, on your site. I mean at LEAST mention his name for God sakes. Also, do some videos over at that large parking lot over at the Bishop ball field complex so you can let them really go wild.

@Giovanniram22 11 лет назад

When you see buying pads, then you understand that there are no modelers any more!

@chrisleech1565 11 лет назад

I think Matt is using 8 or 9 inch dia. blades. He also sells them at his e-store. You may have to adjust the pitch and or diameter of blade to suit the kV of the motor. I am using 10 x 4.5 but with a 750 kV , whereas Matt uses 1300kV with the smaller props for his build. Hope this helps you out

@chrisleech1565 11 лет назад

Hey Matt, can you tell us the parts that you are using for the servo arm and clevis combo. Hard to see exactly what it is apart from the fact it is either a steel or plastic clevis and threaded rod. I have spent some time looking for possiblities on the HK site and I can't be sure.

@cncdeluxe1 11 лет назад

I see your using version 1.5 on KK2 board. (frame # 33.05) You had to flash that into the board sometime. That new version makes for better gyros is what I've been reading. What are your comments on that? Very good video too.

@tshddx 11 лет назад

The tail servo gets power directly from the KK2 board. The KK2 board is powered from the 5v BEC of the ESC plugged into the first motor output. The other motor outputs can also be hooked up to their ESCs BECs, but they're not necessary.

@chrisleech1565 11 лет назад

He is referring to the Hitec HS-82MG Micro Metal Gear Servo 2.8kg/19g/0.12sec They cost a little more but are well made. I ordered one. Tower Pro also makes an equivelant called the MG16R. also metal gear and ball bearings. Happy Flying :-)

@ShortStackalex 11 лет назад

Hey Matt, I don't have a sawdering gun....so I was wondering if you can ship me some pre-sawdered wires?????? I would really love to get started on my tricopter but I dont have a sawdering gun :( BTW I loved the vid!! Can't wait till you make another build.

@rcspeedjunkie 11 лет назад

This is what happens on RU-vid someone make a great informative video, and pricks, nitpick little mistakes. Haters. Good video I fly fixed wing of all kinds and have never thought about doing a multi rotor copter, but your video has convinced me I should

@EverydayKindaGuy 11 лет назад

I like to split my wire with a toothpick and then thread in the new hot lead through the center. Then I split that open end in half and wrap it around either side of the main lead and solder. Makes for a serious joint that never fails.

@DaRobson23 11 лет назад

First very nice tutorial and thanks for that. I have a question about the servo. I can`t find the "L" rod what you use. I look at hobbyking but i can`t find it and i don`t know how its named. Thanks and sorry for english. Greets from Germany :)

@HobbyKing1000 11 лет назад

don't give up on it, it wont fly like his right away you will get mad lol but just keep going.

@iamtheav8r 11 лет назад

Just finished my first Tricopter. Only had 12" props on hand so maidened it with those to get it trimmed out. Seems like it flies well, but the yaw motor freaks out on corrections/wind. Thanks for your help!

@nicolaswalsh 11 лет назад

is the 2 pin black and red wire that connects from the battery to the 2kk board optional, or necessary. what happens if i don't install it, can i still fly, is it related to the low battery alarm? thanks in advance

@JoseSantos-yf1gd 11 лет назад

Please i would like to know what did you hook up on minute 42:28 because my voltage is not coming on the board and we cannot calibrate the speed controllers. Please it is very urgent, I appreciate your help, thanks.

@MrJT270567 11 лет назад

i'm gonna build this thing as well, i download the plan from RCexplorer.se. but this plan looks smaller than your frame. Do use 10mm booms too? what lenght of booms you use on this tricopter? thanks for respond JT

@jcansdale 11 лет назад

I'm surprised you don't put hot glue on the connectors going into your KK board. I always seem to end up with an intermittent connection sooner or later if I don't do this. Do you never find your tricopters dropping an arm?

@HobbyKing1000 11 лет назад

will this setup work with the plush speed controllers? cause i cant find how to flash f-30a's

@rexspurlock 11 лет назад

What dongle did you use to flash the esc ? and where did you get the firmware from , thnx

@TheJoshRed 10 лет назад

Man, your multirotor builds are awesome! I've built your Tricopter 2.0. It's freakin sweet! my only issue is that my low voltage alarm is not sounding when it should. I got the KK2.1 board from you and it's wired up good and all. reads the voltage too. Set it to 108. 10.8 volts. 3s 2200mAh. But it just drops after like 6 minutes of (hard) flying. No warning! when I put the battery on the charger, it shows about 3.3 volts per cell. Quite a bit lower than it should be from what I understand. It seems strange that I hear no beeping of any kind leading up to the power cut. I'm pretty new to the hobby and would appreciate any help. Thanks dude!

@Holy_Algorithm 11 лет назад

I need to know which rod and servo to order at hobyking. I nearly got everything together now, but i´m pretty shure many people would love a full shoppinglist! :) Thank you for that great work!

@ranthm 11 лет назад

Great build video. The best one I have seen on setting up the KK2 board. I do have a question onthe Mix Editor page, Offset was set at 50. Is that factory or your settings? And what does it mean?

@Radcnc 11 лет назад

Lots of fun watching you work Matt, I am hooked, would you mind putting a list of the parts you used, with links? I could not locate the motors or servo you used. Thanks allot Matt you do a great job.

@perriman31 11 лет назад

Correct. I just read the manual a while ago. M1 (motor 1's ESC) powers the board with 5V. Hey, hallstudio thanks for the video, I enjoyed it and understood a couple of doubts watching it.

@vassilijzietseff132 11 лет назад

wow can this man rock an roll,well done bro.just finished my first quad,but hey! tri is defo the way to go for enjoyment. keep the horizon level(if you can lol) good luck dw

@HobbyKing1000 11 лет назад

im about to build mine, its going to take like 2 1/2 hours and ill be doing flips lol

@alaintheriault2164 11 лет назад

Hello , I have a KK2 card for my Tricopter. My problem is that when i start it , it start to turned around and did not stop . Could you help me ... Thank's a lot !!

@chrisleech1565 11 лет назад

That was two months ago! I have already built and mastered tricopter flight (sort of ). Mine is made with a completely different yaw mech. But its good of you to share. :-)

@sumonzahid 11 лет назад

You're awesome, thank you for the detail video on the build. I'm new to hobby. Would you please make a detail video on how you set up your dx transmitter. Thank you.

@davereap 10 лет назад

ESC calibration is a pain.. you need three hands to plug up the wires while holding the buttons on the board...its not easy to plug in then hit the buttons fast enough... an easy answer is to make up a switch lead.. hold down the board buttons with one hand and work the switch with the other..

@johntolman6094 10 лет назад

Try using a heavy duty battery switch rather than trying to catch the window of time allotted. I've switched my power to ESC and my flight control independently. That way you can power up one or the other separately if needed and it makes the response time more manageable for ESC calibration.

@berniebp87 10 лет назад

Thank you for making the KK2 more understandable! I`ve been trying to get my head around the setting and tuning aspect of it, this made me understand it a lot more. Built my tricopter a week ago and have flown it, but that was with analog setting instead of digital (I have digital) Hope this change will make it fly better. THANK YOU!

@adriancjones 10 лет назад

Dang, I wish I could paint like that. The house needs it.

@FlatRat3 11 лет назад

You should have to solder a JST connection to the appropriate spots on the KK2 and then use the method he has on this vid to tap into the wires to the battery.

@chrisleech1565 11 лет назад

Zip tie Gun, Economy model 18 - 50 lbs. It tightens and cuts off the trim $15 - 20. Makes a nice job of it. Try cabletiesandmore in the U.S.A. and Canada