Тёмный

CHEAP ARROW SAW - 3 Tips For Making Square Arrows 

Draggin' Deer Outdoors
Подписаться 8 тыс.
Просмотров 35 тыс.
50% 1

The Harbor Freight Drill Master 2" Cut Off Saw (also found on Amazon) can be a great arrow cutting saw, but you have to know its limitations. Making clean, square cuts is critical for an arrow saw, and in this video I'm going to walk through 3 tips to help this cheap arrow saw meet (or exceed) your expectations.
PRODUCTS USED:
Saw (Harbor Freight) - www.harborfreight.com/2-in-mi...
Saw (Amazon) - amzn.to/3qVHElO
Saw Blades - amzn.to/3jURjHN
Painters Tape - amzn.to/36kKrLN
Arrow Square - www.ebay.com/itm/284035945695...
We hope you enjoyed the video! If you did, please give it a like! And, if you haven't done so already, please hit the SUBSCRIBE button down below! Also be sure to follow us at:
draggindeer.com/​​
/ ​​
/ draggindeeroutdoors
The links above may be affiliate links, meaning if you purchase a product using that link, Draggin' Deer Outdoors gets a small commission (no additional charges to you). We use our commission money to maintain this channel and our website. If you chose to use this link for your purchase, we greatly appreciate your support!

Развлечения

Опубликовано:

 

7 июл 2021

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 77   
@urbanarcher3535
@urbanarcher3535 Год назад
I have the same saw and haven’t changed the blade. I had the same issues with splintering and leaving a lip. Then I tried spinning / twisting the arrow once the blade cut into the shaft and the cut is perfect 👍🏼. I will try the blade you recommended however
@jharchery4117
@jharchery4117 6 дней назад
Very nice. Thanks.
@draggindeeroutdoors
@draggindeeroutdoors 5 дней назад
You’re welcome!
@vincecrandall8400
@vincecrandall8400 2 года назад
Thank you very much, I was just looking at this saw for my arrows and this video helped with the final decision. Tips were very helpful.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Glad it helped! Good luck with it, Vince!
@TomOnTheRun
@TomOnTheRun 2 года назад
Fantastic. Will apply this DIY arrow cutting system for my future Xbow arrow builds. Thanks, DDO!!!!
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
You're welcome! Have fun!
@justin81011776
@justin81011776 2 года назад
Awesome video. I went to harbor freight today and picked up the saw and ordered a 3d printed arrow square from eBay today. Super cost effective way of doing this
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Awesome!! Hope they work well for ya! Mine sure have.
@torreyintahoe
@torreyintahoe Месяц назад
Good video and good tips. I'm thinking about just throwing an abrasive blade on my miter saw.
@draggindeeroutdoors
@draggindeeroutdoors Месяц назад
Thank you!
@buckfever9049
@buckfever9049 Год назад
Thank you!!!!! Super helpful!
@draggindeeroutdoors
@draggindeeroutdoors Год назад
Glad you found it useful!
@KGB270
@KGB270 2 года назад
Another reason why I want to become an engineer. Thanks for the video! You're a legend
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Thanks, Kaanen!
@kurtmeister8308
@kurtmeister8308 3 месяца назад
Great video
@draggindeeroutdoors
@draggindeeroutdoors 3 месяца назад
Thank you!
@40beretta1
@40beretta1 2 года назад
Thank you for your post... I have found in my short time of building my own arrows.. I'll measure.. mark my length...when I cut, Ill leave the length mark on the arrow, just enough, that is what Ill square to ...
@timgruver5932
@timgruver5932 2 года назад
Heck yes! Gotta buy the little carbide cut off wheels they have at Harbor Freight for his saw. Made one 15-20 years ago. Built my own jig to copy a factory made $150-200 saw.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Awesome!!
@moyeroutdooradventures3291
@moyeroutdooradventures3291 3 года назад
I have the same saw, great buy. Nice video
@kaylamarie8309
@kaylamarie8309 2 года назад
Guess I'll be driving that 5 minute ride over to HF tools tomorrow. Thanks for the video.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
You’re welcome! Glad you liked it!
@kaylamarie8309
@kaylamarie8309 2 года назад
@@draggindeeroutdoors Sure did 🙂
@jameyf9464
@jameyf9464 Год назад
Tape the section you plan on cutting with painters tape. Wrap it tight and cut slow. Comes out perfect. No burrs or chips. Lightly sand the end with 320 grit sandpaper then remove the tape
@draggindeeroutdoors
@draggindeeroutdoors Год назад
Thanks, Jamey! Great tip!
@consume_vegetables
@consume_vegetables 2 года назад
I see in my archery proshop, they always roll the arrows during cutting. that could be the key to a cleaner cut. But the drill master saw + squaring tool does cost way less than an arrow cutter jig.
@l.i.archer5379
@l.i.archer5379 7 месяцев назад
The right arrow saw has a vacuum attachment that will keep the air you breathe free of the carbon dust.
@intothemarsh335
@intothemarsh335 2 года назад
We cut and face our arrows on a wood lathe, works like a charm.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
You’re the first I’ve heard say that. If it ain’t broke don’t fix it! 👍
@bostontricker211
@bostontricker211 2 года назад
I use a small pipe cutter I bought at homedepot, works very well too
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Very nice!! Thanks for the tip!
@GertTown
@GertTown Год назад
This is a bad idea for carbons
@jasonhoge5333
@jasonhoge5333 2 года назад
I built a arrow saw over 10 years aga with this saw and mine is set up to rotate shaft while cutting.and still on same saw bought 10 years ago
@kevinshelton3919
@kevinshelton3919 2 года назад
Where did you get the extra disks for cutting your arrows.? Liked you video great information. Thanks
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Amazon, there should be a link in the video description! Glad you liked the video!
@thomascoffman2262
@thomascoffman2262 Месяц назад
If you use a piece of wood to insert the arrow before you cut you will prevent that uneven cut.
@draggindeeroutdoors
@draggindeeroutdoors Месяц назад
Good tip! Thanks!
@l.i.archer5379
@l.i.archer5379 7 месяцев назад
The Amazon version comes with cut-off wheels that won't tear like the regular sawblade would. I bought mine to cut my own cam shims from a bar of 1/2" diam. Delrin, so I wouldn't have to buy premade shims anymore.
@draggindeeroutdoors
@draggindeeroutdoors 7 месяцев назад
Nice!!
@BrothaAustin
@BrothaAustin 2 месяца назад
whats the link to the amazon version?
@longdrawarcher4857
@longdrawarcher4857 4 месяца назад
Might be getting splinters due to the rpm drop. Maybe try going slower and keeping the rpm’s high. Just a thought
@draggindeeroutdoors
@draggindeeroutdoors 4 месяца назад
Makes sense! Thanks!
@acarus3
@acarus3 2 года назад
If you rotate the shaft when you cut it, it gets rid of the burred edge.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
100% agree…but that is difficult to do with this particular chip saw.
@Kycirion
@Kycirion 11 месяцев назад
​@@draggindeeroutdoorsif you or a friend has a 3d printer have them print a nock support to clamp to the table for your length, then a jig that clamps in the saw with a hole a few thou larger than the arrow, this will allow the arrow to spin while maintaining correct length.
@aarongavel1290
@aarongavel1290 Год назад
It would probably help if you were able to support the end of the arrow so that it doesn't drop during the last part of the cut.
@draggindeeroutdoors
@draggindeeroutdoors Год назад
You are spot on, Aaron.
@scottydavis1813
@scottydavis1813 Год назад
@@draggindeeroutdoors I took 2 short pieces of carbon arrows and glued them to to saw so the end of the arrow is not hanging. It supports the tag in perfect
@wolfshollowsurvival4080
@wolfshollowsurvival4080 2 года назад
Does this guy remind anyone of demolition ranch?
@koreydavidson5264
@koreydavidson5264 2 года назад
Set ur saw so it just cuts through the inner shaft. Roll the shaft.
@remlapproductions396
@remlapproductions396 2 года назад
How well does this saw cut moulding?
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Not sure, for me its a dedicated arrow saw.
@jeffrichardson8466
@jeffrichardson8466 2 года назад
New to all of this, but wondering if a pipe cutter like plumbers use would cut carbon shafts?
@greatwhitenorth762
@greatwhitenorth762 2 года назад
Interesting idea. I should give that a try. They are mainly designed for copper pipe and tubing but if you were careful not to put too much pressure on the shaft so as to avoid crushing/cracking it, it may work.
@TheFrenchy47
@TheFrenchy47 2 года назад
That worked for aluminum arrows. With carbon it will damage the arrow. All the carbon arrow manufacturers will tell you to only cut with a high speed saw
@javiermorando4616
@javiermorando4616 2 года назад
The cause for the tail and chips are also due to your arrow not being level.
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Very possible on a cheap saw. Having used it more, I think its actually due to the blade deflecting while cutting. However, I've been able to easily remove cut-end imperfections with an arrow square.
@itechhen
@itechhen Год назад
Spin the arrow while cutting... Simply
@samsien9105
@samsien9105 9 месяцев назад
Look like grinding cutting wheel 3"- 4" size .
@AlexPettit7
@AlexPettit7 2 года назад
Any chance I can get that STL to print the arrow square myself?
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Sure, Alex! Email me, draggindeer@gmail.com
@exodous02
@exodous02 Год назад
Are these carbon fiber arrows or fiberglass?
@draggindeeroutdoors
@draggindeeroutdoors Год назад
Carbon fiber
@graphguy
@graphguy 2 года назад
Use abrasive disks
@draggindeeroutdoors
@draggindeeroutdoors 2 года назад
Thanks, Graph Guy!
@tygappleberry5571
@tygappleberry5571 3 года назад
so if you rotate the shafts while you cut them,,,,,,,,, hmmmmmmm
@draggindeeroutdoors
@draggindeeroutdoors 3 года назад
Hard to rotate them with the chop saw. I have another diy setup that I can rotate while cutting.
@tygappleberry5571
@tygappleberry5571 3 года назад
@@draggindeeroutdoors I was thinking if you didn't clamp it in tight
@draggindeeroutdoors
@draggindeeroutdoors 3 года назад
@@tygappleberry5571 I tried that a few times but it was hard to rotate the shaft evenly while cutting (at least with the saw out of the box). You could probably make a fixture/jig to allow for easy/clean rotation though.
@tygappleberry5571
@tygappleberry5571 3 года назад
@@draggindeeroutdoors hmmmmmmm, You already know don't get my mind to thinking about stuff
@tedbryer2512
@tedbryer2512 2 года назад
You say its cheap? I had to pay $130.00 for mine - Us Canadians are getting totally ripped off!!!
@TheJeepinDad
@TheJeepinDad Год назад
So, you’re saying my Stihl chainsaw isn’t a good idea for cutting arrows?
@draggindeeroutdoors
@draggindeeroutdoors Год назад
Wear some safety glasses and make a video! That’d be something!
@daniel1697855
@daniel1697855 3 года назад
One as noted you need to be able to rotate the shaft as you cut which also as noted you cant do with this set up. Two this blade isnt rotating at a high enough rpm to properly cut the carbon with out leaving those little bits behind. It says "10,600 rpm max" but its not a fixed rpm and has a ramp up speed and will very under load having some big drop off. Professional arrow cutting saws have fixed settings and while yes they too will speed loss it wont be anywhere near as bad as what you get with this thing because they arent using a cheap thow away motor. Id rather spend the $220.00 on the pro arrow saw that has a shop vac vent to collect dust then burn out one of these every 6 months to a year. But thats just me.
@jamescaldwell2616
@jamescaldwell2616 Год назад
You are trying to cut the shafts too fast. Go slower with less pressure and the original blade cuts clean.
@ez7977
@ez7977 4 месяца назад
A Dremel does a way better job
Далее
Tech Tuesday | How to Properly Cut Your Arrows
13:39
Просмотров 26 тыс.
STOP Making Out-Dated Table Saw Sleds, Do This Instead
16:33
СПРАВКА ДЛЯ УНИВЕРА
00:44
Просмотров 372 тыс.
How To Build Your Own Arrows | Bowhunt 101
14:01
Просмотров 149 тыс.
NEW EVERYTHING (Arrow Saw, Components & Arrow)
18:13
Просмотров 31 тыс.
$100 Arrows VS $400 Arrows
13:39
Просмотров 30 тыс.
MODSAW Perfect Arrow Cutter
7:08
Просмотров 1,2 тыс.
DIY Arrow Saw - Easy Affordable Afternoon Build
12:05
DIY Arrow Saw - As good as shop bought?..
19:32
Просмотров 34 тыс.
Modsaw - Affordable multi-function arrow saw!!
14:10
Просмотров 1,7 тыс.
БОЛЬШОЙ ПЕТУШОК #shorts
0:21
Просмотров 8 млн