No video :(

Check DPF System Warning & Stuck In Limp Mode - Mitsubishi Triton - P1498 Fault - Found & Fixed

Подписаться 122 тыс.

Просмотров 9 тыс.

50% 1

In this video I show a Mitsubishi Triton that is lacking power and stuck in limp home mode - It had a fault code stored of P1498 DPF overloading with the check DPF system and engine management light warnings on dash.
Thanks to everyone who watches my videos, Likes, Shares and or leaves a comment. I appreciate everyone of you.
Tool options that I recommend and use. www.amazon.co....
➢ For business inquiries Email : gerardburkebusinessinquiries@gmail.com
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.
2013 2014 2015 2016 2017 2018 2019 2020 2021 2022
Outlander
#P1498 #DPF #Mitsubishi

Опубликовано:

14 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@MiracleMAX 7 месяцев назад

One of the most common faults on the turbo CRDs. They also push the hose off when they get old. Good explanation & thorough repair done 👍😉

@GerardBurkeBurkesGarage 7 месяцев назад

Thanks mate, much appreciated 🙏🙏

@Mr-Keating 6 месяцев назад

Great vid mate. Is definately a common problem and not just limited to mitsubishi.

@patkelly7999 7 месяцев назад

Great work, as always Gerard💯👌👍🙏🙂

@GerardBurkeBurkesGarage 7 месяцев назад

Thanks Pat, always appreciated 🙏🙏🇮🇪🇮🇪 Another one fixed 😉

@gemmanaughton3693 7 месяцев назад

Great video❤

@GerardBurkeBurkesGarage 7 месяцев назад

🙏🙏❤️❤️🙏🙏

@charlotte05060 8 дней назад

I recognised that intersection you stopped at😜, do you have a shop that you work out of and if you do how can one book in. Thanks

@agl5245 13 дней назад

Hi did this automatically come out of limp mode after the new hose had been installed or did you need to do something else? Ive got the same problem

@bryden2008 2 месяца назад

Was the pipe change enough to get it out of limp mode?

@armhags1643 3 месяца назад

hi mate, i have 2016 triton mitsubishi the problem is dpf ligth on and limp mode, same dtc. if im trying to dpf regen its only affair on the scanner executing but the problem is the rpm not up to 2000. stay in idle. i used autel scanner. inlet hose ok.i cleaned dpf, there is any issues?

@superspark5677 Месяц назад

Hi I have the Mq triton and did a manual Dpf burn with the scan tool. It blew out a bit of crap for about a minute then was just revving up for about 25min with clean looking exhaust gasses. Dpf light is still flashing but noticed my oil level is a little high so going to suck a little out and maybe try again. Does diesel somehow get in and Increase my oil level? Will update on this tread with results .

@superspark5677 Месяц назад

So removed some oil to get it spot on and Oil level still high on the scan tool. Used the special function section to reset oil level then rescanned and problem gone. Dpf light stopped flashing also.