Chevy Suburban ABS, STABILITRAK, Traction Control Issue! Tahoe, Yukon Wheel Speed Sensor Replacement 

Great video and explanation. You do need to move your slotted brake rotors to the opposite side of the burb though. They are in the wrong direction

Excellent video, and I like your troubleshooting techniques. One thing, though... You spray brake clean into the sensor hole on the front and that is a huge NO NO... brake clean will dilute and make useless the pre-loaded grease in the wheel bearing, possibly leading to early bearing failure... Best to clean it before you remove the sensor. Cheers!

good video bud, going to test mine. very clear and helpful

I love that you show the mechanic's book and read from it. It tells kids who may be interested in cars and that they need to know how to read!

Great instructions. Your Video is clear and tips are appreciated.

Really good job man, quality work and very informative!!!

I had this pop up for either a p0300 codes aka arcin thru the spark plug boot to the coil mountin nut, like lightnin causin misfires...new cables cured it, to a faulty brake light switch $10 at the pedal, and a faulty oil press sender...all bs as there nothin wrong w the actual ABS or sensors...whatever...jeeeeeez...thanks man...nice vid

The question I have for you is if I should have the Chevy dealer view this video of yours prior to doing the work to rectify this issue once and for all.

You saved me I’m subbed now we even got the same rotors lol 😂 thanks

That's good work. Thanks.

Great job

well done! good video

Specifically, which OBD SCANNER do I need to get to pin-point the EXACT CAUSE of the "STABIL-TRAK & TRACTION CONTROL" issue ? Since 2012, ( when a guy name Lynn Virgil Haas stole my 2007 during this time & had it for 6 months ) I saw "TIRE PRESSURE MONITOR" warnining light. I got new rear brakes and then 2 months later, 4 brand new tires and started seeing the Traction Control & Stabil-Trak Issue. I purchased the Suburban in 2011 in St George UT and it came from an original owner (a Bank President) in Chino, California.

Gotta 07 Silverado. It goes on and off randomly every time I drive but the good thing is it no longer jerks when I go at low speeds for some reason idk why it stopped doing that 😂

10:08 " Pretty simple installation..." Me: 🤔🤔🤔🤨🤨🤨🙈🙈🙈🙉🙉🙉🤯🤯🤯 W H A T ? ! ? I call bullshit. 😂😂😂 Clearly one must have EXTENSIVE EXPERIENCE in Auto Mechanics. NOT a job for a massage therapist. 😂

What else would cause traction control and stabilizer light to come on after replacing wheel speed sensors, spark plugs and wires? There is no play in the wheel hubs or noise, no rough idle. Just comes on and stays on.

Could a faulty abs sensor cause the traction control to come on in my vehicle? I’ve been having trouble with traction control coming on and staying on, rough idle and won’t accelerate. i recently replaced the tps and it minimized the rough idle but that was with it off. With traction control it just stutters when i try to accelerate and i’ll only be able to get some speed when im down hill. It’ll be off and i can drive fine sometimes but recently it’s either off when i turn on the car but comes on when i push the gas pedal or it’s immediately on when i turn the key and won’t come off so i just leave it alone for a few hours hoping it’ll go away. I have my check engine light on as well and my dad ran the computer through it and the engine has about 11 codes but i just wanna know if you could possibly give me some insight on why the traction control specifically could be coming on. Thank you! My vehicle is a 2007 GMC Yukon

Same too today

My 08 tahoe traction and stabilitrac comes on during breaking when its cold out do you happen to have the link to all 4 that you bought

Did your vehicles engine idle rough before you changed the speed sensors?

Got the same 3 lights on ,

So 8 sensors in total ?

I can't even start the engine when i turn the key it cranks like as if i have a dead battery but the battery is reading 12.8

Mine just popped up and has a hard shift from first to second and the engine power is reduced Edit: my RPM was also building up to 1000 when I was rolling on the street with foot off the gas.

Could a faulty abs sensor cause the traction control to come on in my vehicle? I’ve been having trouble with traction control coming on and staying on, rough idle and won’t accelerate. i recently replaced the tps and it minimized the rough idle but that was with it off. With traction control it just stutters when i try to accelerate and i’ll only be able to get some speed when im down hill. It’ll be off and i can drive fine sometimes but recently it’s either off when i turn on the car but comes on when i push the gas pedal or it’s immediately on when i turn the key and won’t come off so i just leave it alone for a few hours hoping it’ll go away. I have my check engine light on as well and my dad ran the computer through it and the engine has about 11 codes but i just wanna know if you could possibly give me some insight on why the traction control specifically could be coming on. Thank you! My vehicle is a 2007 GMC Yukon.