Chrysler Dodge 2.7L water pump replacement with timing chain, tensioner and guide breakdown Charger

Подписаться 40 тыс.

Просмотров 57 тыс.

50% 1

experiment on replacing without taking valve covers and intake off then after all doing so. #howto replace change install Chrysler Dodge 2.7L #waterpump replacement with #timing chain, tensioner and guide breakdown. timing mark step by step tutorial. similar to intrepid and sebring. this was on a 2010 charger.
My Amazon store for featured tools & products: www.amazon.com...
My website for merch/tools/products/contact/socials: direct.me/carl...
Disclaimer:
Due to factors beyond the control of FerKurl, I cannot guarantee against improper use or unauthorized modifications of this information. FerKurl assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. FerKurl recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of FerKurl, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not FerKurl.

Опубликовано:

1 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 97

@bobbydiggs8803 10 дней назад

SPOILER ALERT: TAKES OFF VALVE COVERS. So if that is what you are watching for its probably not possible, no fault to the vid maker its just reality.

@justamag3052 2 года назад

Wish you could have showed us how you turned the cams and stuff it’s kinda pointless telling us about timing if you skipped a major part of it

@FerKurl 2 года назад

Oof. Sorry bro. Hopefully u got some good info out of the vid tho!

@biggchill8176 Год назад

Good chance you help screw someone else down the line but that’s ok because you know the person? Gotcha.. karma is fun

@WDIO-RADIO 2 года назад

Great video, it should be included with the Haynes guide for DIY shortcuts, I really liked the close-ups, super-infomative. Thanks!

@joaquinangel9121 5 месяцев назад

Says to make sure all bolts are off but doesn’t show all the bolts to take off

@larryjohnston52 3 года назад

2004 2.7 GTC 145k miles. I'm gonna try the sparkplug pull and crank advise you offered because bad Cam and CRK sensor would have coded if bad. My only hesitation is Interference Engine.

@FerKurl 3 года назад

Yea see if there’s any liquid in the combustion chambers. That’ll cause your situation. Just had that on a lawn mower as well, bad float/needle in carb caused fuel to pour on top of piston. Acts just like a dying battery when that happens. Pull plug, crank, reinstall plug, fires up.

@soyews 3 года назад

Done this job on three Intrepids. Almost the same. Good job

@doctorrs5317 4 месяца назад

Stupid way to do this.

@fjacks1189 2 года назад

The absolute worst engine Dodge ever built...reminds me of the intrepid,...they just couldn't make it easy like the Ram 4.7 engine, or even the 5.7 hemi...those water pumps just fall off once you get past the fan clutch..2.7 not reccomend for diy's...Hats off to the mechanic!

@pigghedd8245 Год назад

My timing chain cover is stuck on so bad, I’ve tried crow bars. It doesn’t make any sense idk why this could be

@weslambert9846 Год назад

After I set my timing and when I rolled the Eng over I noticed while turning I get slack on pass side then it tightened again is it normal. Thanks

@ronaldpotter3962 Год назад

is that blow buy oil pouring out of that upper manifold ? trade in that car, fast !

@davegibson3763 7 месяцев назад

The new timing chain doesnt have any markings on it????What is the next step?

@meganbowman4747 Год назад

Hi there! I have a question for you... I have the same engine in my Dodge Magnum and having trouble putting the new primary tensioner back in through the hole enough to screw the cap back on. The rear end of the tensioner sticks out too far. Any tricks? Advice? Do I need to tap or pound on it? Thank you!

@Dc-1-2-5 4 месяца назад

Im having the same issue on my sisters magnum did you ever find a way to get it in?

@ynotdoityourself3288 2 года назад

So if no coolant coming out the weep hole and car no over Heating than the water pump good? Or you saying if coolant is in the oil it can still be the water pump ?

@ronaldpotter3962 Год назад

good question, YES

@bennydeal9603 2 года назад

I have a Chrysler 300 2010 2.7 l harmonic balancer will not turn I believe the engine lock up check oil light was on could this be a timing chain issue or need a new motor L

@FerKurl 2 года назад

Could be a few different things. A cam could be locked. Component issue. Seized crank. Fuel/water/coolant hydro locking a cylinder

@walterrichardson43 Год назад

Do those marks on the secondary chains have to be straight up and down also?

@britneynicole9542 4 года назад

What about the cam alignment when timing the crank

@crapschamp4206 2 года назад

The got to be aligned five points little dots on top of the cam gears ⚙ sleight up four.

@tomo7347 3 года назад

Hello, sir loved the video. i replaced the water and oil pump. my problem is the timing chain matalk. 2006 300 2.y I can't keep thew timing marks at 12pm .w camshaft moves when I move the cam to line the holes to put the bolts in sprocket

@mtsanchez27 2 года назад

How did you fix your issue?

@toleasethamasterstylist4481 3 года назад

We replaced the water pump and now it won’t start. I think the timing marks are off

@FerKurl 3 года назад

That’s a good possibility. Something didn’t get hooked back up or timings off

@biggunline1155 2 года назад

How much you charge ?

@kyledevore871 3 года назад

Im doing a complete timing chain, water pump kit. If i align all the tic marks on the passenger cam, driver cam, and lower engine, will that align the timing for the engine? My 1999 intrepid timing i know is off bc when dismantling, the chain was jumping. So im wanting to make sure. thanks for you videos, its helpful. toss some answer my way. thanks.

@kyledevore871 3 года назад

One other thing, which way are the cams supposed to be pointing?

@FerKurl 3 года назад

With timing cover and valve covers off, turn crank (which will also turn cams) clockwise until marks on cam sprockets (not chain) are pointing nearly upwards and crank mark is lined up. Disassemble timing components. Replace water pump. Install new components. When installing chain adjust cam/crank (should only take a small amount because your marks are very close) so that marks on chain match up with marks on sprockets. Your engine should now be in time.

@dannisaurousful Год назад

@@FerKurl so if i didnt mark my cams and sprocket and chain will it still go back in time just by the marks on the 2.7

@dcruz2491 3 года назад

Some did my water pump no chrysler 300 2.7 and just turns won't crank over, what could it be?

@FerKurl 3 года назад

So it cranks and turns over but doesn’t start?

@dcruz2491 3 года назад

Yes

@mrgrow2417 4 года назад

that person does not change their oil as they should look at the sludge .

@FerKurl 4 года назад

Mr Grow very true, it was nasty. These motors are prone to sludge buildup though

@caidenshafer6951 4 года назад

Please help!!!!!!! Are there 3 holes, that look like they need bolts, but don't have it!! They looks like the larger holes. There are threads, but no bigger bolts?

@caidenshafer6951 4 года назад

I dont want to pull the pump if bolts just fell out!

@FerKurl 4 года назад

I believe there is 2 bigger holes without bolts through them

@FerKurl 4 года назад

5:45

@larryjohnston52 3 года назад

2004 2.7 GTC 145k miles. Had a low RPM Oil light flickering. Starter hits Fly wheel, bumps crank and stops. Can spin engine with wrench. New Battery. Good Starter. WTF??😉

@FerKurl 3 года назад

Problem started after doing timing components?!

@larryjohnston52 3 года назад

@@FerKurl Thanks for getting back so fast. No. Virgin timing cover and water pump. No milk in oil pan. Thinking about time anyway but want it running before PM.

@larryjohnston52 3 года назад

@@FerKurl When it was running No Codes.Started acting like weak battery.Starts sometime, with a jump sometimes. New Battery, charged. Relays good. Now Thunk. Starter hit crank like a bull. Ignition to Run logic is askew?

@FerKurl 3 года назад

thats a head scratcher, with the info youve given me ill try to come up with something, last time i had this situation it was coolant in 2 of the combustion chambers, pull as many spark plugs as you can (preferably all) disable fuel pump and spark (pull fuses) then see if it cranks over

@FerKurl 3 года назад

PS, you may have to reply back with a new comment instead of a "reply" for me to see it sooner, its a youtube thing

@spoobfish1273 2 года назад

Wish me luck!!! Chrysler 300 2.7l

@FerKurl 2 года назад

Good luck!!! 🍀

@spoobfish1273 2 года назад

Water pump changed engine is timed. Should I recharge the AC before turning over engine? I'm not familiar Mopar to that degree

@jgtjgt9768 4 года назад

FerKurl, Why is the passenger side valve cover and foam soaked with oil?

@FerKurl 4 года назад

jgt jgt can you be more specific? On your vehicle? Under the plenum?

@jgtjgt9768 4 года назад

@@FerKurl I have a 2.7 Chrysler 300 changed the spark plugs and under the plenum, just like in your video(16:20 mins) the passenger side valve cover and foam had oil. Curious as to why, great video!

@FerKurl 4 года назад

jgt jgt oil can leak out of the valve cover gasket or seals or pcv hose if it has a crack in it. The foam is supposed to be there. Someone could have spilled trans fluid while filling, it’s right above there and a tiny tube

@lifeofjohnbennett9315 3 года назад

Where is you located at I need the same thing done to my car

@FerKurl 3 года назад

Michigan

@lifeofjohnbennett9315 3 года назад

I'm from Michigan from Detroit but I live in Indianapolis and I really need you to fix my motor but I don't have the money to send it to you and pay to get it fixed

@Izzicb 3 года назад

Can u replace just the tensioner

@FerKurl 3 года назад

The hydraulic tensioner on the passenger side? Yes if that’s your problem

@nakorsha555 3 года назад

Hi. I have a question to. I have the same car 2.7 v6 Charger. But I can’t find the water pump with timing kit anywhere online. Only the kits for 3.5 comes up. Do you know where I can order the correct part?

@FerKurl 3 года назад

Try rockauto.com

@nakorsha555 3 года назад

@@FerKurl I’ve look on rock auto, but the site is confusing to me. If possible could you send me the link for the part I need? Mechanic said I need a new water pump with timing components??

@FerKurl 3 года назад

@@nakorsha555 just found it on rock auto and Napa in 1 minute

@nakorsha555 3 года назад

@@FerKurl ok thanks

@FerKurl 3 года назад

@@nakorsha555 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ao3EB_jLL_w.html Made a video for ya

@franciscodelgado8051 3 года назад

Dude how did you get the timing chain cover out ?! I removed all 11 bolts n harmonic balancer of course as said but I'm struggling to get the case out. Help!!

@FerKurl 3 года назад

IF ALL bolts are out it pries off. Work your way around it prying. Sometimes they’re on there very tight and takes a lot of force. Be careful and don’t crack your cover

@franciscodelgado8051 3 года назад

@@FerKurl i speech your response homie. Was able to get it out. Working on reinstalling everything now . Thank you for your video tho it did help !

@FerKurl 3 года назад

@@franciscodelgado8051 thx for watchin ma man

@Bambam-kl1dg 2 года назад

There's bolts through oil pan to timing cover on this motor

@pigghedd8245 Год назад

@@Bambam-kl1dg no fucking way

@doctorrs5317 4 месяца назад

Don’t do it the way this guy did it. He is careless.

@larryjohnston52 3 года назад

2004 2.7 GTC 145k miles. Plugs out. No hydro-lock. Crank spins with a 3/8 drive now. I pulled front valve cover just to inspect. Very clean. Chains tight. It's like the starter hits a dead short between start/run circuit. 99% sure it's electrical. Starter won't spin !! Thanks for all the help.

@FerKurl 3 года назад

Good luck!!!!

@fluidounce 4 года назад

Thank you!! This video really helped me with a DYI. Had a failed water pump caused by chain slack due to the bad tensioner. I did have to do a complete tear down again due to not having the cam chains in time-these also have painted links that line up on their sprockets-5 points of timing

@rocliffbingham6862 Год назад

How long is job take

@MiguelGomez-ms8lx 4 года назад

how you clean the nasty engine like you have can you show how to clean it

@FerKurl 4 года назад

I don’t have a video on that. Here’s a video I found super quick. Skip to about 6:30

@FerKurl 4 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Whv2toBSURw.html

@kiolittlestar 4 года назад

Hey I got a question I have the same car and the guy took out the timing chain to replace the water pump now I am putting it back up and he said he left marks to align the timing chain to where it used to be but it’s not lined up with the line and arrows at all from the mark on the camshaft and arrows ? So which one should it be align to ?

@FerKurl 4 года назад

After the motor has been turned over the camshaft marks will change. Basically whenever you loosen or take off the timing chain you should reset timing completely. Always recommend using a new chain, tensioners and guides.

@kiolittlestar 4 года назад

so does that means the guy set the timing chain right then ?

@FerKurl 4 года назад

It is possible he set it right. If you do the job that way instead of resetting everything it’s easier to make a mistake in my opinion

@FerKurl 4 года назад

I mean it’s less likely to make a mistake if you reset everything properly with new parts.

@kiolittlestar 4 года назад

@@FerKurl thanks man that s helpful I guess I will have to trust it and run the car and see for myself