Class A Class B or Class AB - How to set the bias current with Micro-Cap Tutorial

Подписаться 31 тыс.

Просмотров 13 тыс.

50% 1

This is discussion about what makes an Amplifier Class A or Class B or Class AB? I will talk about the bias current that changes the Class of operation. I'll then show a simulation to illustarate how the bias looks under operation. Micro-Cap will be used and the 20W Class A amplifier schematic will be used in the simulation. It is titled Class A Class B or Class AB - How to set the bias current with MicroCap Tutorial. #microcap #microcaptutorial #micro-cap #classaamplifier #classABamplifier
You can support this channel with this link to Patreon - I really do appreciate your support? This support helps me purchase the equipment I use for testing a reviews.
Patreon.com/KissAnalog
Or you can support this channel with a one time donation on PayPal at: KissAnalog@gmail.com
Link to 20W Power Amplifier Board: amzn.to/3oB0VWW
Class A Power Amplifier Playlist: • Class A Power Amplifiers
Yaung Jing is the brand, and the following is the specifications for it:
Basic Parameters
Supply voltage: DC +/-25V ~ +/-35V
Output power: 20W @ 8 Ohm, 40W @ 4 Ohm, 80W @ 2 Ohm
Speaker impedance: ohm 2 ~ 8 Ohm
Zener Diodes: amzn.to/3qlKoYH
Wire clamps: Wago assortment: amzn.to/3qkY4mQ
Keadic assortment: amzn.to/2N80vKT
Link to silicone lead set: amzn.to/3j23ksq
Link to Blue silicone mat: amzn.to/36qpIqD
Please use this link for the Hiraga Power supply kit:
rover.ebay.com/rover/1/711-53... Power Supply
Please use this link for Aleph 5, Class A Amplifier kit used in this project: rover.ebay.com/rover/1/711-532...
Another Aleph 5 Class A amplifier link:
rover.ebay.com/rover/1/711-53... 5 Amplifier
Irwin Drill and Tap set: amzn.to/3l7coxb
Titanium drill and tap bit set: amzn.to/3rDU1Cz
Tap and Die 40 piece set: amzn.to/2PHTUb1
Cutting Fluid: amzn.to/3qyFR4l
Klein Tool Heavy duty wire stripper: amzn.to/2OcV26n

Опубликовано:

18 мар 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 57

@AllboroLCD 3 года назад

This was fantastic, I million thank yous! I understand the functionality of the classes better, im not fully grasping exactly how I need to apply this to my current amp project yet. Some things take me some time to fully absorb! Great stuff here either way!!

@MichaelBeeny 3 года назад

Looking at everything, heat, distortion, class AB is the answer, with a little on the warm side for the bias. Class B was used a lot in old 60/80s portable radio's were battery life was more important than fidelity. Probably where the early, so called transistor sound came from.

@Oneminde Год назад

Really nice overview. Gives me courage to start simulating myself.

@wafiullah-shafia 3 года назад

Thank you

@TRONMAGNUM2099 3 года назад

Thanks for the explanation. Learned a lot.

@nicoras8803 3 года назад

Nicely done

@frankgeeraerts6243 Год назад

Thanks, nice explanation ....I am still asthonished by this subject be'cause it is so missunderstood by many audio fans ..............in fact class AB is an aberration as it is only a switching from class A into class B ...............in every bias current mode between A and commuting to B..................many so called class A amplifiers are in reality hot biased class AB amps.........and most class B amps have a slall amount of bias current ..

@naadbrahmasound2955 2 года назад

Very nice Information, Thank You

@microknigh7 3 года назад

Nicely explained

@markbosold4050 3 года назад

Nice video on amplifier biasing and operational classes. I'm learning a lot and filling in my knowledge gaps while watching your videos. Thank you for doing what you're doing! I'm new to circuit simulation, is it possible to look at frequency domain to estimate THD with different bias points?

@abhilashgerman2636

Thanks 🙏,Sir,Can you suggest a good sub filter circuit......20-150 hz/120

@be2the4out Год назад

i have a diy (not made by me) Krell ksa-50 , it is 50watts classA. could i tranform it into a class A/AB mix so i have like 100watts on 8 ohm? just by changing the value of the 'bias-resistors' ?

@ianhaylock7409 3 года назад

Hi, nice explanation. I was just wondering, if the positive transistors are running much hotter than the negative transistors, would it be possible to design the circuit so that you have separate bias's for the negative and positive transistors.

@Nightjar726 14 дней назад

In my Marantz HD DAC1 there is a headphone amp. And they recommend biasing to 50mV.

@scottbrady419 3 года назад

Thanks for the lesson Eddie. I built on a simple Class A and a simple Class AB amp on Micro-Cap, but I can not get a decent amount of voltage at RL. The biasing seems correct to me. I've tried driving the voltage higher, changing resistor values and transistors. Also, I don't know what all the transistor info is telling me. Do you have a video explaining the data sheet acronyms from Micro-Cap? Even when I find a design on the internet and build it out in Micro-cap, it doesn't seem to work for me. Can I send your both of these files for your review?

@Taylor_26GE93 2 года назад

Does the bias currents have any impact on the output noise levels? In terms of white noise etc. Not distortion.

@joshaas 3 года назад

oke first of al a real good video, thx for that easy to understand explanation, it's simple this way to understand, you are a good teacher, now for the amp, i like to see the distortion u get from setting the amp in lets say a hot A/B, so let's say the first 10 watt are in class A and the next say from 10 watt to 20 watt its A/B, what's the distortion on that amp bias like that, i think its 0,6 amp until 0,8 amp bias, and what's the distortion if u go the hole way to class A, so the bias at 1,2 amps, with my Hood 1969 amp the bias need to be 1,3 amps to get the hole 20 watts in class A, and maybe not only simulate it but do it to the real amp so that u can see if the simulation is correct or not, is the real amp close to the simulation, that's what i like to see, so again very good video thx for that