Craftsman riding lawn mower won't start no click or anything 

So helpful brother. I had obviously blown a fuse and didn't know where to locate it. This video saved me time on a really hot day.

Your video was helpful to me in fixing my mower! Thanks for posting! !

That was something I never even thought about. I assumed it might be an inline connection of some sort but it was in fact, a 20amp fuse. THANKS!!!

Fiskars StaySharp Max Reel Mower ru-vid.comUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend This is what all push mowers should strive for. It was easy to push. It cut the lawn. The blades are sharp, very sharp. The one minus that everyone should be aware of is you need to be very careful taking the cutting unit out of the box. There’s a plastic guard so you don’t cut fingers as you take the main unit out of the box but it’s not taped down. As I took the unit out, I ended cutting a piece of my shirt. The plastic guard moved and my shirt touched one of the blades.

Thank you! Mine quit out of the blue, I changed the fuse and it started right up 😁

Thank you. U helped me figure out my problem and finally I get to mow the yard. Yay. Not really yay. 😂

Great video it was exactly my problem,Thanks

This helped me. Turns out we had the same problem. Thanks!

Happy you got yours fixed. I can't find the fuse on mine.

Thanks a lot! my PYT 9000 was not starting. Turned out to be the fuse issue.

I have a 20 hp Craftsman very similar to yours. I parked it under a tree and it would not start. It turned out that the last thing I did was disengage the blades. If you own this model you know the spring for the blades is strong. I just let it go and the force of the lever caused the safety interlock wire to fall off inside the hood.

That was my issue. Thank you for sharing.

thanks men your a hero

Mine was a headlight wire shorting out rubbing on hood.

Thanks bro mine done that same exact thing today I’ll check it tomorrow

Man I feel ya

Most likely on most motors the compression relief valve is bad such in my case easy to get started but very hard to repair... there are lots of videos on the problem... which seems to be a common problem...

Thank you! This fixed my Arien’s mower.

Happened to me too fuse was in the battery box on mine but once i traced it down the fuse was blown

I had the same problem on my new mower but it’s got no deck on it and it’s also used but I need to get it started

I have a Craftsman lt 1750.. Is it's doing the same thing. I pulled the fuse and did it continuity test and it was OK.. I notice when I check my electronic shut off under the carburetor bowl it does not jump up-and-down when I turn the key.. I did bypass the solenoid to get the motor running but it's not running very well.. I have a feeling since the 12 V aren't getting to the electric shut off fuels not going up into the main jet. I assume there's only 1 20 AMp fuse.. When I turn the key to the run position and pull the electric PTO switch, I'm not hearing any clicking on the electric PT either. found a 50A relay by solenoid. I checked that on bench..it did click.

i had the same issue. but not only was my fuse blown, my solenoid was trashed.

I have a T110 craftsman riding lawnmower. It wouldn't start so I jumped it with my van. I cut grass 4 or 5 times around my yard. It was supper time so I turned off my lawn tractor and ate. Came back out It wouldn't turn over. Hooked the cables from van to tractor. It only clunks when I turn the key. That was yesterday. I tried it several times this afternoon, it still only clunks when I turn the key. This tractor is about 5 or 6 years old. Bought it new. I also bought a new battery thinking that might be the problem. nope. Got any suggestions.

Thanks, fixed my Craftsman gt3000 23hp

Thanks for the tip. I am not confident that this is the problem on mom’s mower because periodically when I try to start it it will barely turn over by a fraction. Also, it does click so I am assuming that the solenoid is ok.

I replaced my solenoid assuming that was the problem and it still won't crank. Starter cranks if you jump power from the batter to the starter so it's something else. I'll check this fuse out if I can find it. Thanks. Update. The fuse is good. I am out of ideas. I have power going to the solenoid, I can hear the clutch switch clicking when I depress the clutch. Any help is appreciated.

Just had same problem with GT2000. For some reason there was a 15 amp fuse in it and when I stuck a 7.5 in it, it fired right up. Won't run with a 10 amp. either?? Runs fine with the 7 5. Any idea what is going on???

Hi there my mower won't start that might be the fuse can you let me know

IMPORTANT! I own a Craftsman 8200 Pro Series 46-inch lawn tractor with a PTO. Make SURE when you are about to shut off your tractor that you DISENGAGE your PTO. Otherwise, IT WON'T START, unless you DISENGAGE the blades!! I did something I have never done before. I was starting to cut my lawn but hadn't rolled up my lawn hose. Rather than locking my brake and disengaging my blades via the PTO, I just turned it off. Luckily, the Small Engine Clinic guy asked if I had disengaged the PTO (which I normally ALWAYS do) and voila! She starts!! 😊

Can u use ant fuse

Something had to cause the fuse to blow. Did you track down what it was?

My problem is the ignition relay box

Lucky you ...I think mine just had bad fuel.

My green craftsmen kept blowing out those so i put a hard wire in the fuses place it works the same as a fuse and never blows out

My fuse wasn't blown but I'm getting no start or click. I think it's the starter solenoid but I can't find it on my tractor. 🤦🏻‍♀️ Can you make a video showing it?

Swithc on my Craftsman and the 20a fuse, burned out. Got a new ignition switch and put in new fuse and it started/ran great for bout 2 min then motor quit and switch was smoking and fuze burned out again. Wonder what's happening?? Thanks

Fingers crossed this is my issue craftsman t100 2 years old no click or anything and battery is fine.

Good!@@

My fuse was not blown, when I put it back in it started right up?

It was outside for 3 days was raining I go outside it clicked and cranked I jump started no start I pushed it in the garage then there was no click or crank so later I’m check if fuse is blow

Mine is doing the same thing, brand new battery won't turn over or click. I'm about to go check my fuse.

I did put fuse in still won't crank or turn over

But what caused the fuse to burn out?

Dumb question here, but if I check and it is the fuse, where can I buy the replacements fuse

I have almost the exact same mower, brand new battery. Still nothing. I will check the fuse this afternoon...but there is an oddity. On the OPPOSITE side of the gas tank as the Solenoid, towards the frame, I have a small cable with Blue an White Wires. There are two connectors that are not connected to anything. So either, somebody robbed me, which I doubt as I have two German Shepherds where the mower resides, or those wires might be for an PTO or something I don't have? Any chance you can verify what your's looks like? Thanks.

Mine was not blown

I did that but still blowing

3:03

Same thing happened to me with my craftsman riding lawnmower. I have changed the battery, solenoid, ignition switch and wire harness. Just changed the fuse and still no click? HEEEÈEELP!!!

This is such a long video just to find it was a fuse. You really should trim your videos to include only the important parts