Crosman 357 how to rebuild

Подписаться 29 тыс.

Просмотров 156 тыс.

50% 1

This video shows how to rebuild The crosman 357 Pellet pistol this is the older 357 not the new one that has the combat grips when one comes in for repair i will do a video for it, a few things are different in the new model.this one however is the paint ball version but it is the same gun just a different loader and barrel everything else is just a 357 pellet gun you can even use the pellet barrel and loaders in this same fram..

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 459

@ChristiRich 3 месяца назад

You’re still helping Crosman owners eleven years later. Thank you!!!

@KevinMillard68 3 месяца назад

your welcome

@mkstiv 2 года назад

Thank you for this video! My son opened up our bug-a-salt shredder air gun, making all the parts fall out 🤦‍♀. These instructions were exactly what I needed to rebuild it. It works perfectly again!

@KevinMillard68 2 года назад

your welcome

@peterrose6725 5 лет назад

Nice to see a "how to" video by a guy who actually knows what he is doing! Thanks much.

@KevinMillard68 5 лет назад

your welcome

@HistoricallyAccurate247 2 месяца назад

My grandfather and I were checking into his old belongings, and he found this , and because he doesn't know English, he thought it was a toy , and gave it me . Now nothing works , almost, I tried dismantling it to see the problem and it works even less, wish me luck because I will probably never find one like this gem !

@KevinMillard68 2 месяца назад

get your parts from ebay or airgun fourms can also help Crosman will also still have the diagrams as well for all of the guns they have ever made and still make

@HistoricallyAccurate247 2 месяца назад

@@KevinMillard68 I managed to fix it completely with your help , even fixed the broken mill mechanism , thanks sir 😎

@KevinMillard68 2 месяца назад

@@HistoricallyAccurate247 your welcome

@FreakyCommenter 3 месяца назад

had to fix a 357 today. took a half hour trying to figure out where the trigger spring goes😂. thanks for the help.

@KevinMillard68 3 месяца назад

Glad to help

@BOBB1947 11 лет назад

I used the old valve spring in the new valve which made the plunger react like the old one. I also noticed that he valve tube had a smaller inside diameter so I used the old one also. The gun now has good power. Thanks for the advice and again thanks for the great video! Sorry to be so slow in responding but gun started to index poorly so I replaced the cylinder plate and index finger. It now works perfectly.

@bethlennon8799 10 лет назад

Thank you!!! Saved my Vigilante..I had issues with the seer and spring placement..They kinda migrated to the floor after I opened it up..Your video helped me get them back to their happy home =)

@KevinMillard68 10 лет назад

your welcome glad the video helped you

@marcelpaquette3399 5 лет назад

This video is very useful, and now I know where to get the seal kit, many thank's from Quebec, Canada!

@KevinMillard68 5 лет назад

your welcome

@trevorjameson3213 3 года назад

Excellent video, thank you. This is going to really help. I just got an old Crosman 357 just like that one, I think it's about 8 or 9 years old. A friend of mine had it, and it doesn't hold gas, so he just gave it to me. I recently re-sealed my old 1976 Crosman 38T, but it is completely different internally (easier than this newer one). So this video really helps.

@KevinMillard68 3 года назад

your welcome and happy to hear it helped you

@richmoakley 9 месяцев назад

@@KevinMillard68 Oh and by the way I just got another Vintage Crosman 357 Six Delivered Today, The Only Thing Wrong With It Is The Little Rubber Piece Under The Barrel Latch Assembly Is Missing So The Barrel Won't Lock But I Am Going To Order 2 Of Them In The Next Few Days. One To Repair With and One For A Spare. Just Had Another Vintage Crosman 357 Six Delivered On Friday December 8th.and 2 Vintage Crosman 38C's Delivered, One On December 6th and The Other On December 11th 2 Days Ago. I Got A Vintage Crosman 38T That Was Delivered On July 7th. I Have Quite An Impressive Collection Of Air Rifles and Pistol, A Lot Of Them Vintage. My Favorite Rifles Being 2 Vintage Crosman 622's In . 22 Calibers and One Had Just Been Resealed and My Other Favorite Is My Vintage Daisy Power Line Model 889 13 Shot Pellet Pump Air Rifle That Had Just Been Resealed and It's In Mind Blowing Excellent Condition With Not A Speck Of Rust Or Scratch On It Anywhere. It Like Brand New and You Can Smell The Wood On It Fresh and It's In The Original Box, A Lot Of Them Are. I Wish It Was Some Way I Could Send Photos. Thank You Again Richard Oakley 12/13/2023 @ 8:07 p.m.

@KevinMillard68 11 лет назад

the oil will get shot out, but having a tighter valve spring in there could be part one of the lower power , and also if the valve was built along time ago then the stem seal could already be shot, run about 3 bottles threw it and see what happens.i never rebuild valves till its time to use them and i never replace the valve springs unless they need to be done, not sure where you got yours but it dont sound like your valve is operating properly,try what i mentioned and let me know.

@RENEGAD3ml 11 лет назад

very helpful, do you by ay chance know where to get an 8" barrel upgrade for the 3576w?

@stephengraydog3988 2 года назад

THANK for your video, brought, old crossman 357, took it apart, one night, after watching your video, it back together.

@KevinMillard68 2 года назад

Glad it helped

@austinpotts1124 8 лет назад

I am happy to have found this video because it has helped me put my gun back together

@KevinMillard68 8 лет назад

your welcome

@kriswhiteleather3117 10 лет назад

Thanks Kevin! Managed to get a 357 back together without your vid, but it was tricky. The exact same day I got the gun back together ANOTHER ONE came onto my bench! Oye! Second one will need complete seal replacement. Have a set coming from Precision Pellet. Will have your vid bookmarked for reference. Nice work! Kris in NY

@KevinMillard68 10 лет назад

thanks man

@macmanhfx 12 лет назад

Great video! Helped me figure out the parts I needed and made sure I got it back together right. ~Pierre

@heresclowny654 5 лет назад

Im thinking abaut options several of them before parting with my cash, im not a repair tech- so im using an industrial type silcone lube with teflon like moto master 300- its not leaking from the co 2 port so plumbers teflon is out of the question- repair and return will probably cost me 23.00- so if the silicon lube does not succeed then im really interested in watching this and become a do it yourselfer like I've done in the past with my cars on occasions-

@garyphares3532 7 лет назад

Great video! I ordered all of the parts from Crossman and they are very affordable. You can still get most of the parts from them. After watching the video I was able to replace all of the seals as well as a new valve assembly and a new piercing body. At under $20.00 I have a new 357. Thanks!

@N0TYourAverageJoe 11 лет назад

Thanks alot, I'm about to put one up on ebay and was checking for internal rust, and knocked something loose. I appreciate the vid, thank you! :)

@9000Jake1 10 лет назад

Thanks for the video. It helped me get my gun I had a teenager working again.

@KevinMillard68 10 лет назад

your welcome

@cuyler49 7 лет назад

Thanks for the nice video,. Got my 357 back together. Ya tend to forget things when you take it apart. Your video was a great guide to getting it back together. Now, time to gas it up and shoot thru to ProChrono!

@KevinMillard68 7 лет назад

cool and your welcome

@zierottdz7829 2 года назад

This is an effective training video. I was able to reassemble my air 357 after springs popped off and it was a heap of parts. But, just a tip. If you have editing software, you could have flipped the image so that the viewer was seeing it straight on, not up side down. That would have made it easier to follow. Thanks for doing the video!

@KevinMillard68 2 года назад

your welcome happy it helped

@MrRocky1405 10 лет назад

Hi Kevin: I took it apart again and found I had managed to lose the little spring that causes the trigger to hook up on the hammer when the trigger is pulled. I couldn't find it so dug through my "Misc Stuff" and found one similar that I only had to shorted a bit. The gun works great now so that was the culprit. I don't know how I managed to do it even after you had warned us not to lose it. Thanks again for sharing your expertise. Best Regards, rocky1405

@KevinMillard68 10 лет назад

cool good to hear you got her working. ya that tiny spring is a pain sometimes

@nicolasr4731 10 лет назад

a little thank from FRance. My 357 is build. I will try it tomorrow. Thank you again for this video. Nicolas

@KevinMillard68 10 лет назад

your welcome glade it helped

@thodoriskonomos9880 5 лет назад

Very nice video! You helped me solving a big problem in my crossman. Thanks!

@KevinMillard68 5 лет назад

your welcome

@KevinMillard68 12 лет назад

your welcome and yes some of them are total nightmares this one is not to bad i have rebuilt lots of 357 guns

@settiaka 9 лет назад

I have crosman vigilante almost same as this 357. This video helped me rebuild it because when I opened it all parts fall off. I'm missing that little brass piece what u put in that hole of hammer, is it important and do I need it? My gun works when I pull trigger and everything moves but I haven't tested it with Co2 because i'm afraid it gonna blow up and break gun or my hand.

@KevinMillard68 9 лет назад

+Allu if your missing parts then call alan at abairgun.com

@Logan-qq8fl 3 года назад

Thanks this helped a lot although my model is slightly different I got it to work again.

@KevinMillard68 3 года назад

your welcome

@Cross357 9 лет назад

Thank you very much, you save my revolver :D

@KevinMillard68 9 лет назад

Tobi en your welcome

@KevinMillard68 11 лет назад

if your talking about the orings in the pipe they are not orings they are quad seals and are special type regular orings will not hold, get hold of alan at abairguns he can sell you a rebuild kit that will be proper for your gun you have to let him know if you have the new model with combat black grips or older model with brown grips for the proper kit

@KevinMillard68 11 лет назад

well that could be a idea but if there is to much light then you get reflections off the metal pieces and that would not be a good,you could put the video into full screen and select 1080p hd and that might help you

@Coste1072 6 лет назад

My revolver leaks co2 almost immediately after I tighten the cartridge. I don't know why it happened because it gave no warning at all. Do you think a seal kit will do the job? The gun has been well cared for, never dropped or mistreated.

@KevinMillard68 6 лет назад

if its just at the co2 bottle area then just put in a new end seal other wise rebuild kit

@spencer4449 8 лет назад

Awesome and very informative video thank you. i'm pretty sure i'm going to have to get a seal kit. Where do you get those from?

@KevinMillard68 8 лет назад

thanks any where that fixes crosman airguns including crosman or you can also see alan at abairgun.com as well

@TheCecil64 2 года назад

I have done lite work on air pistols - the barrel won’t stay locked - I guess it needs part 357- 021 latch support? The main thing is you can’t get it to puncture the c02. It doesn’t go deep enough to puncher the c02. I screwed it out everything looked good - screwed it back in till it bottom out and still did not puncher the c02.

@KevinMillard68 2 года назад

you likey need a new pericing cap as well as the latch boot

@TheCecil64 2 года назад

@@KevinMillard68 Ok and Thank You.

@SoulDrawn 8 лет назад

It's 2 in the morning when I'm at that stage where I revert to childhood play and I was tinkering with the co2 storage, imagination amok. Out of nowhere I wanted to see what was inside, and so I unscrewed it and opened it. Holy shit, that was a mistake. it's now almost 6 and I've just now put it all back together. Mine is slightly different with the index bar, and minor other things, but good lord that was one of the most arduous and tedious and painstaking moments of my life. When things flew out at me when I opened it up, and then when everything else fell out later, I was so sad; I thought I had basically ruined it

@KevinMillard68 8 лет назад

+SoulDrawn yup yup they can be tricky

@bravehrt17 10 лет назад

Ok...manage to find the kit. while installing it, i drop the gun.... I put all back together...and i ended up with one extra(!!!) spirng... I think is the one you describe in 3.05 that its on the hammer..but i dont understant where excactly i have to put it... The gun looks like working properly, but i didnt install a gas yet..untill get an answer for this.... Thanks

@KevinMillard68 10 лет назад

take a really good look at the video, for where the spring goes if all else fails goto crosmans website and you can download free print for the gun

@bravehrt17 10 лет назад

KevinMillard68 ;) Found it. Followed the diagram..and everything works just fine. Very useful video for me...and good support also!!

@Coste1072 6 лет назад

I forgot to ask. If you recommend a seal kit which kit would you recommend. I believe that with your video I can take it apart & reassemeble. Thank you

@KevinMillard68 6 лет назад

you just need a 357 complete rebuild kit

@BOBB1947 11 лет назад

Thanks for the great video. Thanks to your great step by step instructions my rebuild was easy. One thing I have noticed though, is that my gun seems to have a little less power than before. My seal kit contained the complete valve and CO2 inlet assembly and the plunger is stiffer than my original. Also there was a lot of oil in the valves. Would these affect the power? Again thanks for a great video.

@KevinMillard68 11 лет назад

did you get this thing brand new cause if you did then take it back if not then call alan at abairguns after 6pm his time and he can set you up my stock of 357 pats is really low right now and the parts you need i dont have in stock at the moment..

@AzBroAzMaN 2 года назад

Awsome video got me back up and going thanks man

@KevinMillard68 2 года назад

thanks and congrats

@ricardorayas8515 4 года назад

AMIGO PARA FELICITARTE EL PRIMER VIDEO MAS ESPEFICIDADO QUE HE VISTO ESPERO TENER TIEMPO PARA VER TODOS TUS VIDEOS SA

@KevinMillard68 4 года назад

thank you

@gordonnguyen6905 11 лет назад

Hi, I just bought a Crosman 357 gun and the problem is that, the latch support is missing! Also another problem is that the index finger spring is missing because it won't spin the cylinder! I don't know what those parts are really called so if you can help me figure out those names and website to order them it will GREAT.!

@someoneqc 10 лет назад

Hi sir! Thank you for your video! I have and old 357, with the 8" barrel, brown grip. It started to leak at the top of the CO2 bottle once screwed in. I've just sent an email to ABAirgun for some info on how to proceed to get my gun repaired. I'm from Canada. Thanks again for sharing this video/tutorial. Take care.

@KevinMillard68 10 лет назад

your welcome

@GueroObs 6 лет назад

cyou change the barrel on this gun can you tell me which barrels you can put

@seweedsew8286 11 лет назад

i would be interested in your services. do you have an email where i could send you more details??

@red2965 4 года назад

Kevin I was wondering if there was anyway to get better volume out of the cylinders but I guess after watching this that it's preset, also I dripped mine out of the cabinet it was in to a cement floor about 4' and the barrel part jambed back to the cylinder pin I moved it back but it was way to easy to move have any idea's how to stabilize it? Great video but camera was a but out of range for a good view. Thanks for posting it it does cime in handy if I was to try to repair one I have two and what weight of oil is that your using? 10w?

@KevinMillard68 4 года назад

no idea without having it my hands to see the damage that was done

@76hotrodF250 9 лет назад

Question Kevin, I have the old 357 "brown grips" but it was missing the parts in the c02 puncture area. The gun was my brothers and I wanted it fixed. I bought a kit off ebay that came with the new valve assembly prebuilt, just drop it in and screw case back together. He sold it as a kit for phase 1 and 2 guns, but I noticed it is for the newer guns. However I installed it regardless. It does shoot, but its only giving me a small percentage of power, not even enough to push a pellet out of the clip. I messaged the seller and he said it could be the hammer or hammer spring. I doubt that, I suspect a blockage in the jet or valve perhaps? I really want this old gun working again.

@KevinMillard68 9 лет назад

order in the parts for the original valve/gun from alan at abairgun.com dont ever but seal kits for any guns or older crosman guns off eaby always goto alan he is the best and has the proper parts . you might have gotten a bum valve and the newer valves SUCK rally bad. FYI never email him , call him only after 6 or 6:30 pm kanas time ..

@milkapeismilky5464 Год назад

I fear I'm much too late, but thank you SO much!

@KevinMillard68 Год назад

your never to late to fix your own guns its getting the parts for the vintage ones thats the challange check ebay

@KevinMillard68 11 лет назад

i never heard of it so i have no idea, i only use crosman pellgun oil or Sae 30 non detergent motor oil

@MainAvel 10 лет назад

Not only Crosma uses that sort of valve (the ones you need that funky tool for). So does ASG. And also some Umarex guns

@KevinMillard68 10 лет назад

nice to know ,

@lomgshorts3 5 лет назад

Have two of the "old model" .357 Crosmans, this will help a lot in their maintenance. Thanks. Who has the best "O" ring seals? Or do I find the similar sized "O" rings at the hardware store?

@KevinMillard68 5 лет назад

abairgun.com has the best kits and parts access even for the older crosman guns best to call him so he knows what version of the 357 you have they did make some changes over the years

@texasroots 2 года назад

Hello Kevin. Great Video. Thank you. I think the latch support boot wedge fell out of mine. Have you ever seen that happen? Any recommendation of a replacement part for it? I could probably get creative about wedging something in there if necessary. Very helpful to see how it was designed in your video.

@KevinMillard68 2 года назад

never seen one fall out but they can dicenagrate for sure and you can order in a new one from crosman just carfull when you open the gun if you pop either one of the quadseals on the brass pipe out youll need a new set of thoes as well

@texasroots 2 года назад

@@KevinMillard68 thanks for the quick reply. Havent used it in a long time. Went through first clip great, accurate. Reloaded and the latch lays flat. Mine is an older model, hopefully the wedge is the same.

@nogach 8 лет назад

Videoanleitung - SUPER! Danke.

@KevinMillard68 12 лет назад

thanks and your welcome glade the video helped you out

@TheMightyPooh420 11 лет назад

As far as I know there are no restrictions here on pellet guns. Were can I find an 8 inch barrel? Could you do a video showing how to perform said mods? I'm not trying to take anything more than small rabbits. I have a .22 and a pellet rifle that has plenty of power but I'd like to be a bit quieter and I like using a pistol for compact reasons also. Thanks for your response. By the way I eat everything I kill (except rats)

@paulmartinez6934 4 года назад

I have a daisy powerline model 44 I’ve had it for three years old I want to bring back too

@KevinMillard68 4 года назад

i dont fix airguns anymore and never really got into fixing daisy the only 2 guys i knew in canada that did are both passed away now so i have no idea who might still be working on them

@jamess521 9 месяцев назад

A friend gave me a crossman 357 to see if i could repair it for her. Your video helped me tremendously, but i was unable to repair it for her. How can i go about getting this to you look at?

@KevinMillard68 9 месяцев назад

you cant i dont repair airguns any more the cost of parts and labor make it unaffordable to people sp fixing it your self if your best bet but you can tell me whats going on and i can do my best to help you that way

@jamess521 9 месяцев назад

I didn't realize and am seeing this was a video from 10+ years ago, so for that I apologize. Thank you for your assistance.... So I took apart the pellet gun because it just leaks. Assumed it was the seals so I have them ordered, but in not sure why as soon as you puncture the co2 nothing stops it. 2nd issue, the pellet magazine if you will, doesn't spins. I can seem to find that part listed. Any ideas.

@chbronco 5 лет назад

Well it is a vintage one,and has a custom BSA log barrel. I live in Alberta so I would be looking at 100cdn?

@KevinMillard68 5 лет назад

your looking at 54.00 for the basic rebuild kit this will not include a new face plate or indexing prawl which i advise strongy to do + 35.00 labor and shipping costs both ways iam in ontario there is no mark up on the parts i dont make anymoney on the parts at all. it takes about 2 weeks for me to get the parts ,, crosman canada wont have the parts for vintage guns, so i have to get those parts from the USA and before i can even order in the parts ihave to know which version of the gun you have of the vintage series there was changes made to the linkages for the trigger as well as the indexing prawl as well. so that now adds more time on getting it done and back to you..

@orinhaugen7164 11 лет назад

Hello I have a older model 357 that was passed down to me. It needs a new seal is there any where I could get one pre built before I order a seal kit?

@aquaknot5672 9 лет назад

Thanks Kevin, I appreciate your help. Hal

@KevinMillard68 9 лет назад

your welcome

@KevinMillard68 11 лет назад

yup you can power mod it for a bit more fps how ever the best thing for power and keeping it legal is find your self the 8 inch barrel for that gun it will take the gun just so very shy of 500 fps , as for small game it wont take much more then some chipmunks and some small birds.

@richmoakley 9 месяцев назад

Great Video! Thank You. I have a Vintage Daisy Power Line Model 44 that I need to get back together, I have everything back the way it's supposed to be except for the hammer spring. It goes under the hammer first I think before you put the hammer back in but for the life of me I can't seem to get it in there just right. Anyway you can get me to somewhere I can find out how to position that bad boy back in right? I've got 3 Vintage Daisy Power Line Model 44's all together but I'm not going to take one apart to see if I can see how it goes because I don't want to have either one of those messed up. The one that I am having trouble with is one that I purchased as is, saying that it was in working order but had to be put back together because they had ordered a new valve assembly and the hammer came out when they took it apart and couldn't get it back together right. I have put back together and built a Crosman 357 Six successfully basically just like the one you're showing here. The barrel latch assembly wouldn't latch and ordered a replacement and put a new one in.

@KevinMillard68 9 месяцев назад

all the guys i knew that fixed daisy guns all pass away now but you could check online pellet gun forms for someone that might be able to help you out there likey will be a few guys there on one or more of them

@richmoakley 9 месяцев назад

@@KevinMillard68thank you Kevin, I appreciate it. I'm Sorry About The Loss Of Your Friends! God Bless Them All In Heaven!!! 🙏 I've lost quite a few Friends and Dear Friends and Ex Girlfriends and Sweetheart In The Last Fee Years Going On 3 Now and All Of My Dogs Have Passed Away Too. The Last One, Buddy, 13 Year's and 8 Months Left Me On September 25 2020 and The Next To Last One, Mr. King, 13 Year's and 5 Months On April 25 2019. There Were Many More Going All The Way Back To 2000. I Got My First German Shepherd, Smokey, Back in 1990. Thank You Again

@richmoakley 8 месяцев назад

@@KevinMillard68 Hey Kevin It's Richard again. Hey I finally got the 4 pack of seals to replace the old worn out seal's in my 4 Vintage Crosman 357 6's. One of them did not have the little dust screen under the piercing cap. I cleaned up everything and put the new seal in over the piercing cap and screwed the holder screw back on. I haven't tried it yet but I was wondering if it will work without the little dust screen in there? Thanks

@TheMightyPooh420 11 лет назад

I'd like to modify mine for more power. Is there any way to do that with this particular gun? I would like to be able to take small game with it.

@bravehrt17 11 лет назад

I rebuilted, and installed a new gas cartidge, without installing the cover plate, just to figure out where is the gas loss. Its definetely from the last point before pushing the pellet. So, something is wrong with the part that needs the special part to screwed back...

@fastg111 10 лет назад

Awesome Video. A big Help. Thanks!!!!!!!!

@KevinMillard68 10 лет назад

your welcome glade it helped

@don9126 2 года назад

The video is very instructive. How to order a repair kit? Tks.

@KevinMillard68 2 года назад

call crsoman see of they have one for you for the new model guns they should as for older 357s Ebay or see if you can find a USA shop thats still fixing the old ones

@bravehrt17 11 лет назад

I replaced the o-ring, with one of same size, but still all gas is running out fast from that release point, just before barrel. what can be the fault in my gun? I dont have access to service center in my country... Is something else related to the release of the gas in every shot mechanism? Thanks

@SmittysPlace 6 лет назад

this is great but the assembly you installed for the seal where the co2 sits, mine leaks, can this be repaired without the tear down?

@KevinMillard68 6 лет назад

its tricky but yes

@Patriots2327 11 лет назад

Thanks and where can I get the crossman tool u used in this video?? Or since you said you fix these could u fix mine, how much would it cost?

@masona7219 10 лет назад

oh and can you take ot the barrel and put a new one in and send the barrel back so i can make my own black powder .177

@KevinMillard68 11 лет назад

yup new and old models no problem

@Xavie_roblox7 3 месяца назад

Thanks i had a 40 year old crossman gun and it wasnt working an then all the parts fell out it was my dads fathers that was passed on to me

@KevinMillard68 3 месяца назад

your welcome

@nubnub9635 3 года назад

I've had one for a few years just recently it stopped cycling the cylinder reliably. What would be a common cause of this? I used the old and new cylinder, the old one cycles better than the new one...

@KevinMillard68 3 года назад

face place has platic pressure spring that wares out so get a new one and a new indexing prawl and you good to go just be careful not to disturb the seals in the pipe or youll be doing them as well

@strelok6833 11 лет назад

Hey kevin, im from central texas and was wondering how much it would be to send you my Crosman 357, i got it in the mail after ordering it. the weapon preformed well but i was out and about on a "Recon" when i heard a clank in my pistol...i opened the case to find that the firing rod had come out of place...nothing appears to be broken, i just not 100% sure the "Correct" way to put it together

@TerryFry 9 лет назад

Can I change the wedge by myself without breaking the seal you were talking if you take your Crossman 357 apart? I ordered the new wedge (the piece that helps support the latch at the barrel break) i have the brown grips which is the older model Crossman 357. Is there a video on how to do it? Thank you for your video!

@KevinMillard68 9 лет назад

Terry Fry the side cover must come off to change the support boot, you have a 1 in 10 chance that you wont toast the quad seals when you pull the cover

@thanatos387 11 лет назад

Is Teflon oil safe to use on this gun? I bought it recently and I'm not sure how to oil it other than the oil drop that goes on the co2 cartilage

@nenshitemorgan519 6 лет назад

Very helpful video. Thanks.

@KevinMillard68 6 лет назад

your welcome

@aquaknot5672 9 лет назад

Hi Kevin, I have one of the 357's but believe it may be an older one. The grips are brown plastic and the right hand one is held in place with two screws. My question to you is, do you still repair them, and if so, would you be willing to do mine? Hal

@KevinMillard68 9 лет назад

i dont repair them anymore sorry i dont even have any parts left i got right out of pellet guns , you can get the parts from alan at abairgun.com just let him know which 357 you have and get the parts from him its really easy to fix them ,, call him after 6:30pm his time zone faster to call him them to email him

@bradhinz1 9 лет назад

Kevin, I just purchased one of these guns in the original box. It has one issue. The rubber piece thet supports the latch for the barrel is not working i think it is dried out. Do you know the part number or where I might get one? Thank you for your help. Brad

@KevinMillard68 9 лет назад

Brad Hinz its called a latch support boot and you can order them from any crosman repair depo or call alan at abairgun.com

@TacoViolator872 9 лет назад

thanks. my nephew will appreciate it.

@KevinMillard68 9 лет назад

Tadpole B your welcome

@ThePistolero35 11 лет назад

Your video was very useful to me mate ! Thanks , well done ! :)

@kriegmeister3000 10 лет назад

The 38T is a lot easier to put back together . Nice vid you made.

@KevinMillard68 10 лет назад

either one to me is easy but after you do it a few hundred times i guess anything is easy lol

@KevinMillard68 5 лет назад

your very welcome

@MrAlexanduh 9 лет назад

great video! I have a similar Crosman Vigilante, with a broken barrel latch. is there anywhere that you know of where I could get a replacement part? thanks!

@KevinMillard68 9 лет назад

+MrAlexanduh if the place you bought it from also repairs them then goto them other wise any place the fixes crosman airguns doa google search and you can also goto abairgun.com as well for crosman parts

@seweedsew8286 11 лет назад

Hi there Kevin i was wondering if you are still rebuilding the old 357 crosman pellet guns?

@bravehrt17 11 лет назад

I tried to contact. no answer. I replaced the o-ring you use in 5:20 of the video. Can rapid loose of gas from that position, conected to the "quads" (i suppose is those 2 on both ends of that brass pipe)? Or can it be because of the part you replace in 6:50 ? Thanks again

@bravehrt17 11 лет назад

Nice Video! My 357 loses all gas from the front hole (before the barrel). Where do i find a seal kit? I searched with no luck... Thank you!

@KevinMillard68 11 лет назад

glade to hear the video helped you

@gordonnguyen6905 11 лет назад

So my gun's barrel keeps on falling down because the latch support is gone!

@deadcelebrity 5 лет назад

What sort of paint should one use on one of these for touch ups to match the color as best as possible?

@KevinMillard68 5 лет назад

I dont do little fixes i strip all the paint off and redue it complety youll never get a match of any color to blend right

@KevinMillard68 11 лет назад

good to hear

@KevinMillard68 11 лет назад

the one iam working on in the video is the older 357 not the newer one and the indexing prawls are different , the bb version uses the older indexing prawl as does the older pellet version,

@heresclowny654 5 лет назад

I'm sure they should have a parts rebuild kit for all cr 357 model made dates somewhere- i was looking at this flick and figured on ordering my part i need, its the leaking seal ring(s) but i guess you or i would have to contact crosman and may not like their price and keep checking-

@josephbourque1503 9 лет назад

The latch on my gun does not latch! I think the latch support is missing. Can that support be purchased and can it be installed without taking the gun apart? If not, where can I send it for repair and what is the cost?

@KevinMillard68 9 лет назад

+joseph bourque you can buy the latch support boot seperat yes and your old one is probely still in the gun just worn right out ,. and yes the gun must come apart. if you live in the U.S then send it to alan at abairgun.com if you live in canada find your nearest repair centre if and only if its a new version 357 if its and old school one then you need to send it to alan at abaigun or find someone in canada that fixes old and new crosman airguns...

@heroesgrantorino 3 года назад

If you swap the valve for a more powerful one you can add a lot of power. Best mod you can do. Peace

@KevinMillard68 3 года назад

there is no more power valve for the 357 but i do know the mod for the current valve the hammer spring can also be upgraded from the old style to the new one for more power as well

@BLOOKERIA 11 лет назад

will you put mine back together and redo the seals?

@t-mankimbrough7766 6 лет назад

What is the thing that the air goes thru called mine is not keeping the air in the cartridge when I screw it in it leaks in the gun and I just got it from my older family member and it is still very nice and will should just don't hold the air.

@KevinMillard68 6 лет назад

end seal for teh co2 bottle and there is also 2 quadseals that leak as well ,, my advice get a full rebuild kit from abairgun.com and rebuild the valve and all the seals and might as well get a new hammer spring as well and she will be just like new again

@t-mankimbrough7766 6 лет назад

Thank you very much

@PiperMV 6 лет назад

Do you still do repair service? I've got a Crossman 357-6 that needs rebuild. I am in Pensacola FL. If so, what do you charge? Thanks. Nice, informative video!

@KevinMillard68 6 лет назад

nope sorry i dont , however you can goto abairgun.com and can help you out

@mlpmlp6988 8 лет назад

Great video. Thanks.

@KevinMillard68 11 лет назад

google abairguns that will get you to his website with contact info and no you cant call him this late at night.just tell him what parts you need and he will know you will by the way also need a new set of quad seals .

@richardappleby8211 2 года назад

my near new Vigilante is not releasing gas when the trigger is pulled. There is pressure within the 2 cylinders I tried but it is not get through to the cylinder

@KevinMillard68 2 года назад

they have crapy valves these days known problem crosman still has not fixed so just order in a new valve and your goof to go till it messes up again, if you pull the trigger enough times it will work fine again for awhile till its screwes up again i reallt dont get what the problem is yet with the valves i havea customer with the same problem and they only real fix is to find and older verison 357 valve and then your good to go for 20 years as well as its got good seals in it hard to find those valves tho i have one and they do go for big bucks when you can find them

@KevinMillard68 11 лет назад

ok so what your saying is your valve stem seal is shot then ,

@KevinMillard68 11 лет назад

your welcome glade to have been of help to you

@carterholliday9594 11 лет назад

hey bud. were are you from. myne is from 1979-1987 can remember. would like to get it fixed. i got it apart to check wats wrong. its all still sealed. but it needs a new barrel clip and rubber clip holder. and a new c02 seal. also needs to be sited in. are you in canada or the states. if in canada, were about.?

@carterholliday9594 11 лет назад

also needs a hand grip... lol left side. dark brown.