CRX Si - Installing the Skunk2 Alpha radiator with the Innovative Competition series traction bar

Подписаться 1,1 тыс.

Просмотров 3,9 тыс.

50% 1

Does the Skunk2 Alpha CRX radiator fit if you have an Innovation Competition traction bar installed?
I've read forum posts. I've read Facebook group comments. I've read Amazon reviews. Some people say you have to mount the radiator at an angle. Some people say you have to cut out the supports in the hood. Others say you need to weld tabs on to the traction bar.
I FIND OUT.
Parts:
Skunk2 Alpha Radiator 👉 amzn.to/2UkERHd
Innovative Competition Traction Bar 👉 innovativemoun...
Tools:
Ryobi impact drill 👉 amzn.to/3vX1y0E
Ryobi driver bit set 👉 amzn.to/3gWYT2Y
Read my guides on joelguerra.com
My video & editing gear:
GoPro Hero 9 👉 amzn.to/3iOOc3Q
Apple MacBook Air M1 (2020) 👉 amzn.to/2S3zOJT

Опубликовано:

13 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@joszefspitefull9319 2 года назад

Great video... You calmed me down because I ordered the same radiator for my ef and everyone says it doesn't clear the hood

@joelatwar 2 года назад

Do you have the Innovative traction bar too?

@joszefspitefull9319 2 года назад

No... Just the factory

@joelatwar 2 года назад

Oh right, it fits even better with that

@DIYKAI 3 года назад

I run a s2 radi with the traction bar on the stock mount mine is perfect as well

@Athon08 7 месяцев назад

My bottom radiator support must be bend. I can’t close my hood. Going to trim some for the underside away and see if it fits

@jonnymiskatonic Год назад

Nut crush test is a good test.

@toddtyler1682 11 месяцев назад

Pretty much same setup and my cap hits the hood lol.

@spoolin2bars 3 года назад

Nice, next time put a dab of silicone to test instead of the peanut. lol

@joelatwar 3 года назад

The peanuts were right there!

@mrme9517 Год назад

Nice Radiator I'm debating on the skunk 2 as well or the ebay Aluminum Radiator but what way did u route ur Coolant Overflow Tank did u go the direction of the outlet or curve it over to the passenger side instead thanks just getting ideas 💡 😎🍻

@joelatwar Год назад

The overflow is in the factory location on the drivers side. I had to use a longer hose.

@KD-dx9hm 2 года назад

Thanks for the info

@qt8541 2 месяца назад

what is that intake heat shield? and also it wont fit in the hatch, its crx specific. i had to cut part of my hood fo0r the cap to fit

@joelatwar Месяц назад

It’s custom shield made from some aluminum sheet

@sdfam7 2 года назад

What did you do about the loose driver’s side of the radiator?

@joelatwar 2 года назад

I welded a tab with a hole in it to the traction bar. The peg coming off the bottom of the radiator sits right in the hole and I put rubber gasket so no metal on metal vibrations.

@sdfam7 2 года назад

@@joelatwar thanks Brotha!