A step-by-step tutorial on how to cut, arch and seal your fenders before installing widebody or overfenders on a Honda S2000. This works for most other cars too! LIKE & SUBSCRIBE!!
I can understand riveting to the rear quarter but taking the rear bumper off is an essential for me so maybe in my case id use riveting nuts on the bumper
the arch is very well done! way better, safer and nicer then most people do. but before putting on that black stoneguard stuff on the bare metal i wouldve at least primered the arches twice. especially on bare metal you need to build a proper paint build up. and especially when that part gets basically sandblasted by the tire all the time. if that car is more then just a trailer queen then there will be bare metal again very fast. also you didnt speak about what you do to the inside of the wheelarches i think? if the car isnt properly protected there as well, rust will eventually form on the welds. btw. i think rivnuts are great for kits like that. its a good thing if you can remove your kit without a hassle to repair maybe a crack, repaint a part quickly, fix your inner arches or just clean behind it. 🤷♂️
Good point on the primer before applying rocker guard, I will do that in the future! As for the inside portion I will certainly look into using a weldable primer. Rivnuts are great in many cases, but imo they look goofy on widebody.
@@lock_to_lock id use at least some rust protection wax on the inside of the arches. on an s2000 bit hard to reach every inch of the arch but it is possible and the car is protected.
Damn, that s2k is clean! Dude, clecos are a game changer when it comes to anything sheet metal related. Love the side clamps for flat panel work. Killer video as always man.
Sorry bud, this is slightly better than the slit technique but this is still not the right way to do it. The right way is to cut the high line on the outer skin. cut the inner skin and separate where the 2 seams meet if you can. Roll a sheet and swage a flange line ideally but not necessary. Can either lap weld using stitches spaced 25-50mm apart or if you made the flange spot weld. Then stitch weld the rolled tub you made 25-50mm apart and cut the excess and seal everything up. Essentially it's the same but comes out a lot cleaner and doesn't warp the outer skin. Fully welded is not necessary.
Appreciate the love, Thanks for watching! You definitely can run a seal on the flares, but I don't think it is absolutely necessary. The customer needed this job done quickly so I made it happen with what he gave me.
Nice. I need to do this too for mine, since i only used carbon fiber bondo to sealed it 4-5 years ago. Good video! Very informative. Since i will be repainting the car, i will need do this as well.
Great video, I'll definitely be doing the same when I install my wide body kit, with the front guards, they don't have an inner guard that needs to be cut does it?
Great video! Saving it for later. The previous owner of my S2K butchered the fenders when he tried rolling/pulling them. As a result, I'll probably go wide-body eventually.
if thats clean id like to sell you your next race car ... well it was 2 cars before lol.... we do it different in the uk mostly custom fabbed steel arch liners then custom plastic liners ... to avoid rush noise etc
is this method applicable on 2016 mustang? i mean heating the inner fenders and hammer them when they r new and not sliced ? or do i need to sliced them so i can stretch them like u did? cuz i dont know man if they were new and the gap is big , i feel it not gonna stretch till it meet the otter fenders
@@lock_to_lock thanks for ur reply, i did alot of searching, unfortunately not too much videos for mustangs, and the videos i found all of them doing the slice bend method, it seems like ill take my chances doing it
Would still avoid cutting slices if you can, I'd bet you there is plenty of material to hammer up to close that gap after cutting your arch. You got this!
Hey that’s awesome work Alex my son is wanting to the same on a Subaru legacy wagon but he’s having issues getting the wide body kit wondering if you’d be able to help us out, we live in Vancouver Bc Canada thx hope to hear from you
Very nice work man! I have to cut mine also the right way the 2nd time, 1st was a quick cut no one needs to see what that looked like but 2853018 18x11 square rubs a lil bit. hahahaha!
@@lock_to_lock So point proven for using rivnuts? He now has to take it back off to paint it lol Wide bodies absolutely come of fairly regularly on cars that see the track.
@@lock_to_lock being ugly is an entirely invalid argument for this video 😂 In the video you claim "stop pretending you're going to take the wide body off". Wrong. Wide bodies become a wear item on track cars and they do come off. Rivnuts can be re used and take 30 seconds to remove the panel. Rivets have to be drilled out and restocked every time you take the panel off. You don't have to like rivnuts but this video and your reasons for it make you sound like a moron. No one is saying rivnuts look good. But on a track car they just make sense.