I think my dc blue advanced pro stopped working. When I followed your guidance to left, It gaves me E1 error and it continuously beeping. Should I get someone to fix it for me? thanks.
@Monyadiwa thank you for the comment, if you have an aluminum door and it only works when the door is open or even half open, then your door is blocking the signal, you can install a weatherproof receiver on the outside of the garage, but it requires you to run a cable to the receiver
@@nicksandtrickssa so i did that i programmed "b" to the blue button and it showed me "1" now when i get back to standby when i press the blue button it just shows me "p" and it starts beeping
@@nicksandtrickssa i just followed the instructions and im where you say i should close the door on the blue thingy so when the door closes it flashes "E" and "1"
Thank you for your comment Llewelyn, unfortunately, E1 is either your encoder or PCB that cannot read the encoder, so you have to take it to a repair center, Rsec Security Equipment Center in Bergvliet, or an installer can do it for you.
@@nicksandtrickssa thanks for the reply. took of the cover. looks like some burn on the white 3 pin plug where it says encoder on the pcb. the resistor next to it also looks fried
@@llewelynklaase7896 , that could be the source of the E1, also the resistor bottom left is for the battery, mb door too heavy, if wooden door, that can be cause as well
Thank you for the comment Mark, at the top, where the battery is, there is 4 phillip head screws, be carefull as the cover will drop when you loosen the last screw. Also note that 8 out of my last 10 repairs was faulty replays and software that was needed to fix the E1 the other 2 was faulty inner motors or both issues
This video was so helpful. I managed to close the garage door completely. It was very frustrating during windy days as it would blow in the leaves. And shaking the door constantly.
Thank you for the informative video. I used it to set up my door, but I'm experiencing a different issue now. Every time I open the door, it stops halfway, and I have to close it before trying again. When I try opening it a second time, it works. Do you know what might be causing this?
@@cebongcai740thank you for the comment, it could be the door is not weighted correctly, or just the weather making the door act up, change the F, force, setting for now and set it back when the weather gets better
Thank you for the comment Lloyd, yes there should be a bracket at the top of the motor where a 24V3.5Ah battery sits. A sub to the channel would be great, thanx
Thank you for the comment, 3 means no transmitions received, either the remote is too old or not on the correct settings, press and hold your ET remote button until it pulses slowly then try again
Hi Nick, please assist if I press close on the remote it will go down and as soon as it reaches the bottom it will automatically go up again and open. I think the setting went out but don't know how to reprogramme it.
Hey. Just watched your video. I've got the DC Advanced. I cannot add extra remote. All my remotes just beeps when I press the button. And it is stuck on b. Also when I want to do the quick programming holding the up button does nothing on my motor. I've tried switching it completely off and on again Still stuck on b
Thank you for the comment David, if your looking at it right side up and its a small "b" it means the beams are active, if you do not have beams, do the following... press and hold set, scroll up to capital "A" press set to confirm scroll down to number 0 and press set to confirm it will take you back to small "p" now scroll up to small "b" scroll down to number 0 and press set to confirm then press exit and exit again, you should now be instandby mode to half 11 on the screen, press the remote and see if the door runs we will address the adding of remotes after
Hi. My chain got stuck, and i had to remove and return the motor to loosen the chain. Now my remote doesn't want to work. I tried setting the limits and did everything according to your video. The only difference is that theres an intermittent beep at the end after the unit closes itself. I see in the video that your system only beeps once and goes to P on display. I get an E 1 error. How do i fix that
Thank you for the comment, E1 error is encoder error/motor fuse blown, if the motor moves even a little then it's a PCB issue and you would have to send it away for repair
How do I check the fuse ? I don't want to get a technician out if I can replace a fuse. How do I do it ? Many thanks for your other videos,got it working initially, but now got E1 code and won't move.
Apologies for late response, the fuse is at the top by the battery, 8 out of 10 motors I get with E1 has faulty relays and PCB needs updated software, the other 2 is an encoder failure on the inner motor or both failing
Thank you for the comment Dreshni, there should be a red string hanging from the middle of the draw bar, pull it and you can manually open and close the door, be careful tho
Thank you for the comment, if it's 2 half lines, it's in standby, if all the remotes does nothing as well as the buttons on the display, then PCB faulty... If you give me more info I can assist
Lastly,i have 1 remote which was working together with the one on the wall but after i did some toughing to the buttons trying to program second remote,all the remotes are no longer working. Can you maybe assist what could be the problem?
Hi Nick's and Tricks... Mine is also showing "b" and the other buttons don't work... How do I exit? When I press the remote is beeps a couple of times then stops and nothing happens
Thank you for the comment. Press and hold set, go up to r, press set, go to b, press set, go to C, press set, press and hold the remote, 0 is clear complete, 3 is unsuccessful, try again
@@nicksandtrickssa nope. This happens once the remote is coded. It reads 1. Once you exit and test the remote, it opens the door but does close it. I'm close to you store in bergvliet and will pop in to seek help..🤣. If , however, I'm doing something wrong please advise.
So the thing is... These thing don't just stop working, if you think back to when it stopped you will find the culprit that damaged the receiver, you will have to purchase a single Chanel receiver and program to it, please also check if the PCB is still ok, nothing melted or blown
Great video thanks. How does one remove the beeping sounds as the motor is opening and closing, very annoying and loud but can’t seem to find instructions for this anywhere
It's flashing E & I after opening, and I think it's beeping from that warning message. I don't think we have a sensor (tilt garage door) and it does this when power is connected, so all the time once the garage is opened fully. @@nicksandtrickssa
Thank you for the comment Bobby, problem with that is every site is different and every gate is different, and I gues noone in the industry want you to do it by yourself... If you get hold of a manual it really tells you exactly what to do tho.
Hi Nick. Thanks for the video. I set the limit and added anew receiver successfully. Problem: The Garage door opens but when i try closing, it beeps and shows a "b". What could be the issue?
Hello sir my garage door when close will open but when pressing the bottom again to close it doesn't close instead it shows a 'b' sign and the light goes on
Good day Unathi, thank you for your comment. U have to disable the safety beams and Auto-close. Check out my video on enabling those settings and instead on 1, turn to 0. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-W56yUv6ZB_g.html
