in this content, I explain to you how to recover or fix the defective module, how to work it back as a normal working module and here I teach you how to flash and update the module back to the normal condition.
Kapatid i have a Cummins qst 30 with gcs and dse 7310. It gives ecu shutdown after crank. The ecu fault flash code is 1211.i swapped the mpu it would crank for a bit longer but then again ecu shutdown code again
I had commented about my defective dse5110 . You responded to my comment but found later that the modules I was buying wasn't at all authentic Deep Sea Modules. These were cheap Chinese manufactured knock offs and made to look like Deep Sea Electronics modules. They even use DSE logos and claim to be Deep Sea Modules. That's exactly why these cheap imitations won't at all hold up and stay working correctly. With this, I contacted DeepSeaElectronics in Chicago Illinois and placed an order for the Deep Sea Electronics DSE 7210 MKII with Heated Display.
it's always good to have both options on the table concerning panel rectification. can i please get to know about the flashing procedure as well please?
Go to your app thin connext module to the latop and find the upfate firmware after that onece you click its show what type of module and version u want juat follw instruction deepsea give
@@benzblogsVlogs my brother.. I've try to solve that problem memory corrupt..but when update using update firmware it stop bcos there is a password on the deep-sea electronic control board..what is the next step?
@@DaveTopi-jb9ss its should no password make sure that previouse config did not put any password from the module coz should not be asking pasword during update
@@benzblogsVlogs my brother good evening...we have put password on scada>maintenance>module lock.. someone try to change the setting..somehow memory corrupt..cfg1 eng1 and etc appears on screen..therefore we use update firmware but on process it stops updating at 71 %
Thank for all you do here. i have a DSE8610MKII that is displaying MSC data Error hence it is not communicating with the other DSE8610MKII is the synchronizing panel. how do i solve this problem thanks
Check how many pcs you synch thin end to end should have 120 ohms thin double check the connection if there is wrong or ither reversly connected or cut thin if same msc fail ahm check the multiset in the config ither wrong program
Yes sir do this check your battery if good condation check the fuel thin try to bleed to remove the air in the fuel galery agter that start again use manual pump at same time crank it
I have a similar problem to the 7410 MKII model. I have updated the program and before the download is completed, the update stopped and a note appeared on the model’s screen. memory corruption refer to manual . What is the solution please?
What firmware update you did just put the latest updat on it like if version 1 update it v1.1 or 2 like that in order to work make sure update is propperly done
My module is called DSE6120 MKIII. The problem is that the generator output is measuring 234 volts Phase to Neutral, but the module is reading 275 volts Phase to Neutral, causing the generator to shut down, what could be the problem?
hello i have a problem with my DSE 6020 MKII which can not come on when i put the power inside but when the computer is connected through the DSE software it can come on . what could be the cause of that?
@benzblogs after flashing our module and all lamps are red instead of making configuation manually as you did in this video; can we also copy directly to another module wich working and paste on our modeule directly
hello, good night, I have a deep sea 7320 which presents the common ac fault, and even if I flash it, the fault continues to appear. I hope you have a good day and thank you very much for your help.
Help with the link for the flashing. And even while working on the Memory Corrupt, I didn't see what you operated on the laptop, the camera is only showing the display board of the DSE.
Ok even without flashing i found out just go in the app open deepsea thin go to click the firmware update thin select the model ang version of your module thin write it ok thin back to normal
Thank you for the help however there's still more. When the panel doesn't display and just the LCD backlight showing but still works with the buttons. What are my to do. Do I need any flash file and how do I get it to return to display.
Hi, Bro.. how are you ? Hope you are doing well. I am SALIM from Singapore. I have watched your video. I have a device model 7320 which is the same issue as mentioned in your this video. So please advise me to solved the issue and share me to link and flash file. Thank you 🙏
Hello friend, thank you very much for your video, I'm following you from Angola and I have a deap sea 6110 module that suddenly its screen had first turned to writing and now it turned black. Can you give me a tip on how to resolve this? I am grateful to you from now on.
If only disply is gone and its working meaning ither lcd is problem or just adjuat the contrast of your lcd now if still same thin open check the ribbon of it clean it and put it back
Hi Benz, I have the same problem on a Deep Sea 335. the error message displayed: ''Memory corruption Refer to manual''. can you help me with the restore procedure or the link for the Flash program.
Just simple open your deepsea connect to your latop open config in the top you can see update firmware thin follow the instruction select the latest version done
We are encountering an error with DeepSea Module 7320, which has been unused and is displaying a calling application error. I have attached a snapshot of the error for your reference.
Hello sir.. How to fix communication failure only when we want to write configuration to module DSE 7420 MK II? But the application success to read the configuration from the module. Thx..
Do one thing connect paower supply after that connect the usb to the latop check if any communication betwen your deepsea and the laptop if there is thin update the firmware if no thin meaning to say that your module if fully deffective or not posible to repair
sir i connected dse 4520 controller to my pc. but controller detect model no. 4523. this model not availble one dse website. pograming procces not done.. please help me sir
Hi I'm Boakye from Ghana please my module screen displays memory corruption and in this video you reset the same memory corruption but you didn't show the procedure so please make a video to teach us step by step.thanks.
I have problem with dse7310 control panel BRUNO GENERATOR Display lights up but no words Buttons work e.g engine starts bit then it will cut out after 5 seconds. Your video shows buttons not working. Can I re program this?
Sir i had 6010 MPU V.1. 5. The timer symbol is always and i cant start the genset.even i lower down all timer setting but its always on. Whats the problem
Sir, anong compatible laptop para maka download ng software, windows 8/10, 32/64 bit? tsaka po anong gamit nyo na cable to connect from laptop to the unit (DSE 8610)?
sir, am trying to flush a deepsea panel 7320MKII. You said you would send us a link to help us during this process but it never comes. can you please help us out with that link for flushing?
During the proces open deepsea connect usb to the latop and deepsea put supply for deepsea thin in the aplication click in the top firmware update thin look my yt how to do it
Boss our controller shows *memory corrupt*but this was done due to the dead of CMOS battery I replaced the battery but the problem is still there,so how can I rectify this problem
Sir no need what ever the module your doing just update it at higher version of same type of the module go the the latop open deepsea in the top you cleck the update firmware and follow the instruction geven to by the deepsea app while doing the update ok
No more flash file needed go to you computer just update the firmware of your module after that follow what is the instructiom given to you there that it
Hello Sir please i need your help I have dse7310 MTU Generator my display is showing memory corruption refer to manual and AC comms failed. Please what can I do. Many thanks in advance
bro just open the deepsea app thin find the firmware update and follow the instruction during the process using the highest version during a firmware update.
Sir benz, magandang araw sa iyo, i have a deep sea module 6020 mkii the problem is i can't edit any parameter in this module and all indicator lights are lit, is there any solution on this?...
Simple thing open your latop connect your deepsea go to update firmware update it in higher version and follow the instruction what computer says that it and also follow what i do in the vedio
@@benzblogsVlogs i have this problem to with dse7320 to, what step i need to do, i see your video but i dont see your leptop screen and how you do it, so please what i need to do mister
@@khairulanam6395 simply open deepsea config connect the module and ho to update firmware update it in higher version and follow the instruction during process
As this years no jeed that flash file go to update firm ware thin follow the steps and after that done but if you have a new latest mk3 is not working now deepsea is update it my be because you know
@@benzblogsVlogs Hello bro, I have a found a problem my my deep sea controller , I wanted to copie a old version of deep sea module 6320 v.2.3 to another more récente version 2.7 , it was impossible cause the version was old than new module . Then, I decided update firmware the version of my DSE module 2.3 to 2.7 , but I seen that version 2.7 was not what I wanted ? How can I put my module back to his old version ??? I really need your help please?
sir san makabili ng pra flashing at software pra sa DSE..meron ako dalawa na generator ung display nya mawawala minsan meron at minsan baligtad ung graphics pero meron siya ilaw at gumagana din sa manual at auto start..ung display lang ang problema..anu kaya issue sir. salamat at more power.
My module is called DSE7320 V7.0. The problem is "MEMORY CORRUPT REFER TO MANUAL", When I try to update firmaware to the lasted version 14.0 the dse config show me" INCOMPATIBLE HARDWARE UNIT IS MODEL CODE 7320, MODEL VARIANT 0, HARDWARE VARIANT 1. FIRMAWARE FILEIS MODEL VARIANT 0, HARDWARE VARIANT 2." PLEASE HELP ME Mr, thank you.
Yung DSE 8610 MKII ng cummins genset namin, pag start mo nag crank sya at umaandar, ang problema wala syang display na voltage, speed, frequency as in no display ng parameters. Ano kaya problema??
Check mo sir gamit multi meter para sure kong may volatge talaga after kong meron check mo sa likod ng module yung wire na V1 kong may pomasok na voltage okay po