Diagnosing a BENT axle shaft flange the easy way

Подписаться 59 тыс.

Просмотров 90 тыс.

50% 1

In this video I bust out the dial indicator and find out both my axle flanges are bent causing my brake pads to flop around and make a bunch of noise. I replace them with some new shafts and it is good to go. These are 35 spline Yukon axle shafts with Timken SET20 bearings in my built 1980 F150 Ford 9 inch rear axle.
Check out our website: muddybeards4x4...
Amazon Store: www.amazon.com...
Get 10% off your purchase at Barnes4wd with this link or use “muddybeards” at checkout
www.barnes4wd....
Get your OnX Offroad Free trial and use Coupon code “Muddybeards” for 20% off your subscription. subscribe.onxm...
Get 10% off your Yes Welder purchase and using coupon code “muddybeards”
yeswelder.com/...
Yankum Ropes: yankum.com?afmc=1v
Get 10% off Olight Products, with coupon code “muddybeards4x4” www.olightstor...
Get 12% off the Setpower AJ30/40/50 With the coupon code: “MuddyBeards4X4”
www.setpowerus...
Tools I Use, MotivXTools: www.motivxtool...
10% off coupon code: muddy
www.setpowerus...
DISCLAIMER: Due to factors out of the control of Muddy Beards 4X4, we cannot guarantee against improper use or unauthorized modifications of this information. Muddy Beards 4X4 assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Muddy Beards 4X4 recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Muddy Beards 4X4. Be safe! This video and description contains affiliate links, which means that if you click on one of the product links, we receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!

Опубликовано:

11 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 61

@ironbearjku2233 3 года назад

Ive had bad luck on my rear 44 with yukon shafts twisted splines all the way around the shaft warrantied them got east coast gear supply shafts and zero issues new yukons are now spares

@bsideadventures2180 3 года назад

Thanks for the videos Kelly and thanks for your service sir.

@ambitousresolve1179 3 года назад

I bent mines on my old mustang sliding sideways into a sidewalk curb. Destroyed front passenger side rim and rear axle shaft I think. Also cracked my rotor almost into two pieces.

@VonChapo07 2 года назад

I brought a mustang with that exact problem in okc are you who I brought it from 😂

@ayybee8184 2 года назад

No way this story is true. No pedestrians?

@Lilsquirt772 2 года назад

I did the exact same thing 💀

@ambitousresolve1179 2 года назад

@@ayybee8184 I lost control in the rain is that hard to believe

@ambitousresolve1179 2 года назад

@@VonChapo07 lol no i kept it for another year

@jamesmerkel9442 3 года назад

when I 1st heard about this problem of flange bending running giant tires I knew the fix, God model would hve pre-bent flanges b4 the r used on the axle. Ppl didn't understand, but quit simple, if thin plate will bend simple math then bend it making it in press then attach flat plat to the pre-bent plate w/filler brace wedges. This way still ultra thin light efficient axles for spinning but just pre-bent so can't bend while using imposs load used to make flange then 2nd flat thin plate & filler wedges. I only speak english unlike satan santa so hope that was clear enough diff person hearing it. 6 press 20ton bends will b indestructible finish product.

@mrjmartinez15 3 года назад

How much is the acceptable runout on axle flanges?

@nichobob1 3 года назад

Love the build Kelly super surprised the shaft was so far out, I was wondering what size coilover you used and what bracket Love the channel and your amazing TJ

@jadenreececoffey9196 2 месяца назад

Is that why my rotor keep clipping up on my caliber bracket? Whatever problem I have literally pushed out my brake pad clips

@yerwrng 3 года назад

I don't have those problems with my fully trusses and shaved 14 bolt ...you guys and your 🌈 9s ;-)

@jassonco 3 года назад

You made that harder than it needed to be KISS.

@rickmarquart3277 3 года назад

Great video Kelly!

@donaldstrishock3923 2 года назад

The "Flip" was 144 degrees at the best, not 180. Them "Jumbo" wheels cause "breakage & bendage" when "off roading"--just an expensive hobby. Thanks for the great Video Sir and happy safe Wrenching.

@gailhill8391 11 дней назад

If it moves WITH the rotor rotated, doesn't that mean it's the ROTOR?

@antoniomontana9425 Год назад

I have the same problem. change the axle shaft and differential fluid and still the same problem

@jesserousseau2481 2 года назад

My trucknis doing this extract thing. I've replaced inner hub bearings rotors caliper pads tires rim all.new. dealer says hubs do not normally warp..

@FrostyMikeGaming 2 года назад

I have a question about a back axel on a truck and say if there was something wrong with the axel and say that person was touching the axel to see if there was something wrong can he get shock or burnt by it if the car was turn on with motor running? My friend has a Dodge truck and he's always crawling under it to see if it's damage and i'm just worry that he might get burnt or shock by it and really I don't know anything about car repair so I thought my friend would get hurt while the car was running.

@jesserousseau2481 2 года назад

Mine is a way diffrent set up in my 3/4 ton of course but I need to make sure and figure out how or if my axle is bent.

@jopyjetta 2 года назад

Did you feel any vibration with the axle bent?????? And if you do at what speed???? I can’t find the source of vibration in my truck

@ayeyaeye 3 года назад

Excellent.

@Jasonfuntime 2 года назад

4:20 not super hard on my jeeps

@David_Mash 5 месяцев назад

So was it just the bearings in the axle tube???

@jeremiahallaire3180 2 года назад

Hey! How did you rule out the housing though. A bent axle tube would also cause a wobble on the flange no?

@MuddyBeards4X4 2 года назад

Very true, but when I changed the axle shaft the wobble would be the same if it was the housing, not almost completely go away.

@frlcf3159 Год назад

Thanks for the video! How do you know if it's not caused by the bearing vs. the axle?

@zodiac8208 3 года назад

The consequences when Nate said: pretty easy.

@ruubguus4321 3 года назад

Hahaha 👍

@MuddyBeards4X4 3 года назад

🤣 true

@mleukus Год назад

could you see the flange looking out of line when it turned??

@macknumber9 Год назад

I'm confused how a bent axle would cause a wheel to wobble...one would think the axle being bent would cause a fixed camber issue but not a wobble...perhaps the axles were in fact bent but it was the bearings also failed (if enough force bent axle then also damaged bearings) causing the wobble...

@nikasumo 9 месяцев назад

Think about it..if the flange is bent it will wobble with every rotation

@danielmagalhaes5739 3 года назад

Awesome! I think it's a good ideia check you axle housing if isn't bent. That can cause your axle shafts to bend. Btw what is your front axle?

@MuddyBeards4X4 3 года назад

Yea, there is a possibility that it’s a little tweaked. My front is a hp Dana 44 out of a 76 f150.

@danielmagalhaes5739 3 года назад

@@MuddyBeards4X4 well the thing is here in Portugal i can get easy the rear ford 10.25 from a van but they are 4x2... and i can't get something that pairs with that axle.... but... keep up! 💪💪💪💪

@Fix_It_Again_Tony 3 года назад

@@MuddyBeards4X4 Have you always used the RCVs in the front or was that an upgrade after some broken shafts? The tires are 40's, right?

@MuddyBeards4X4 3 года назад

Yes, 40’s. I broke one U joint /axle shaft and upgraded maybe a year later. But the break was my fault, I didn’t have my bump stops set up correctly so the tire was stuffed in the fender and then broke the axle. I Didn’t have an issue after I properly set up my bump stops.