DIY 15in 4-Drawer Base Cabinet Carcass (Frameless)

Подписаться 231 тыс.

Просмотров 24 тыс.

50% 1

Written Article/Plans: rogueengineer.com/diy-15in-4-...
Links to other projects in this series
Frameless Cabinet Carcasses
-7in Slim Base: • DIY 7in Slim Base Cabi...
-36in Lazy Susan: • DIY Lazy Susan Carcass...
-27in Sink Base: • DIY 27in Sink Base Cab...
Subscribe on RU-vid: bit.ly/rogueSUB
Subscribe to Our DIY Life (Vlog): bit.ly/odlSUB
-------------------------------------------------
SUPPORT ROGUE ENGINEER
Buy a shirt: bit.ly/rogueSHOP
Shop on Amazon: bit.ly/rogueAMZN
Shop at HomeDepot: bit.ly/rogueHD
-------------------------------------------------
BE SOCIAL
/ rogueengineer
/ rogue_engineer
/ rogue_engineer

Хобби

Опубликовано:

9 фев 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@buciobuilds7316 5 лет назад

Your blog post instructions were the best I have ever seen. Nobody shows how to use all of your plywood sheet efficiently and takes the time to sketchup each step like you did. Making this cabinet later. Thank you!!!

@rogueengineer 5 лет назад

Thank you for the kind words!

@bukatasv 6 лет назад

Great work!

@ChrisBrown-fx5jn 6 лет назад

Curious what type of overlay do you use where two cabinets are connected?

@jeremiahwilliams1897 6 лет назад

Just curious what your method is to painting the edgebanding after applied? Thanks.

@paulhett 6 лет назад

Looks great..... you make it look too easy 😜

@rogueengineer 6 лет назад

Haha thanks Paul

@WayofWood 6 лет назад

I have recently seen the Kreg drawer jig used by various people quite a bit. Is there any advantage of this approach to just using 2 scraps screwed together in a 90 degree angle?

@rogueengineer 6 лет назад

Scraps would probably work just as well in most cases. This jig has a couple tabs that make it a little easier to setup for face framed cabinets and its got a wide ledge on it so you can flip it around to support the drawer when attaching it to the slide.

@WayofWood 6 лет назад

Rogue Engineer Thanks!

@Kenfitzpat 6 лет назад

Just a question about the Kreg drawer installation jig. Nor a criticism but since you installed the drawers after the box was installed why wouldnt you have used it not only for the slides but also on the outside to attach the drawers to the slides. To me that is beauty of this jig allowing you to install the slides and the drawers with the same jig. Like I said just a question. Your cabinets are beautiful and I look forward to your videos.

@rogueengineer 6 лет назад

That is a great feature of the jig for sure and I'm not sure why I didn't do that. I guess I just figured it was just as easy at the time to take the slide out, flush it up with the front of the drawer and bottom then screw it on the side.

@number6396 2 года назад

I was excited to see your frameless series, but then I watched a couple of the videos. They are useless. No instruction. Just watching you build without explanation. Not helpful. Very disappointed. Confusing to go back and forth between two people building. Who knows who is building what?? Noticed the comment below about your blog post being useful. I will check that out. Hopefully it is better than the video.