DIY 96-00 Honda Civic Wheel Stud replacement 

The dog under the car with no jack stands scares me

thanks for the video and great detail. now i can change my buddys wheel stud free of charge and get us back on the road 😎

i love how your dog is under your car watching you work lol

Thank man... This help so much, I thought I was going to have to replace the entire Hub

Thanks for the upload. Just had to change two on a '99. But I really didn't have the clearance like there is on yours to remove and install em. I had to finagle em in. Also, it would've been really good if you said to remove the bolts for the "caliper bracket". Not the caliper bolts. I know you said 17mm but still. Remove bolts holding on the caliper bracket and the caliper will come off with it.

Thanks for the informative video brother. This helped me a lot.

Good job. Good video. Hate the lug nuts, dude. LOL.

Great video! Feel like I wanted to see the tightening of the new stud/bolt more. That's the part I'm most worried about. Also, how well does it drive now? Smoother than when the stud was broken?

Thanks! Will be doing this later now to both front wheels lol

Great vid! Dude! Thanks! 👍🏻👍🏻👍🏻

Thank you very much, I just snap on of my bolt but with your video I feel confident to repair it !! 👏🏾👍🏾 love your videos !!!!!!

The video was suuuuper helpful. Thanks for that! :)

Great Video! Dude! Thanks for sharing! 👍🏻👍🏻👍🏻

Just watched the video where you put the turbo kit on the civic and wondered where you tapped in for the wastgate lower tube? A lot usually go off a valve on the turbo but I'm guessing yours is going to the inlet manifold? Did you get any issues from doing that if so? Also, Did you have any issues with boost leaks using those boost pipe clamps and couplers or did they seal Well? Finally what psi spring is in you're BOV? Sorry for All the questions but I'm about to do the same thing Thanks

Wheel stud will not clear hub. Any tips?

Give that doggo a ratchet too

Also works on 2013 Honda Civic LX 1.8 L

The reason they didn’t want to come off and they kept rounding is because it’s not a philips screw,

Very good work ! Thank you very much !

Well shown, thanks. ;)

I don’t know how yours was so easy because everyone tells me you have to grind down the side of the top or you have to takeoff the whole hub assembly weird

how long did you drive around with only three studs on there I have one that's totally stripped out and have to replace it but I have to go to work and don't have time until later on this evening

This is not accurate for a 01 civic ex coupe. I can’t get the hilt to go through at all, I’m guessing I’m going to have to replace the hub. The splash guard and the back of where the stud goes, there’s not enough room behind it for me to get the stud in.

All you need to do it’s heat up the bolt comes right off

How much did those lug nuts cost you? they look so cool!!!!

Amazing!! Tks man

How are you turning the wheels with the car raised like that?

Where u been bro need more videos from u hey what part of Florida r u from

Put anti seize on the screws that hold the rotors on!!

This is not for 96 00 civics you have to disassemble the whole hub assembly

Dude, thanks for the vid but one thing: is one of your dogs resting under the car while it is only supported by a hydraulic jack? Be careful FFS! :)

I have a 2000 and it looks different than this like the stud will definitely not come out even after cutting it

Anyone else wheel stud not want to come out when you hit it, mine is starting to flatten the more i hit it

Will you drive it soon again ?

Nice. (no spikes pls)

I went and bought the impact screwdriver but there’s no screws on mine !??

That hammer needs a new sparkplug, it was missing a little

how much would one stud cost to replace on a rear drum?

there is a cut on index 7:40

Great hammer of Thor lol

then you have to put that red stuff on all the wheels

What year is your Honda? Dude?

DO NOT screw a nut on to pull the stud through. I made the mistake of doing it and now i can't get the damn thing back off. The entire stud just spins and spins

what year is your car?

Mine hits some shot in the back annoying af

Almost looked good...until the lug spikes. Worst trend to happen to vehicles.

There is no way