DIY: CertiFlat 24"x48" Heavy Duty Welding Table! LEGIT!!!

Подписаться 4,9 тыс.

Просмотров 12 тыс.

50% 1

Hi everyone! In this video I assemble & weld together the 24"x48" CertiFlat heavy duty welding table and leg kit! This is a FANTASTIC table and I'm extremely pleased with it. Check it out!
Links to the welding table & leg kit:
CertiFlat 24"x48" Heavy Duty Welding Table:
weldtables.com/collections/pr...
CertiFlat 24"x48" Heavy Duty Leg Kit:
weldtables.com/products/lk244...
Please be sure to LIKE / SHARE / SUBSCRIBE!
If you have any comments or questions, please drop them down below.
Email Contact: RU-vid@ShowPhil.com
Music Provided by:
RU-vid Audio library
My Gear:
Samsung Galaxy S8
DJI Osmo Pocket
Canon VIXIA HF R600
GoPro Hero 3+
Nikon D7000

Опубликовано:

28 дек 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@anumowt

Great Job!

@sixbolt 2 года назад

Thanks for the video, about to start welding the same exact setup !

@user-td3xz8xz9h

The stringers in my kit were not flat. The table surface had more than close to 3/4” crown. It’s impossible to flatten the table when the stringers are warped. I would look at the arcflat table from Langmuir.

@lawxr6eBay 2 года назад

Brother, thanks for the video, glad to see you cover everything I was interested in. Not to Preach but if you've actually got a TIG setup you'd have been better off practicing your TIG Skills on the weld out.. That many welds would have your skills much improved. Clean up a few mistakes in the beginning but then a whole bunch of practice and only minimal grinding . I know you were ready to gitter did though. Good Job👍

@treborterb Год назад

Nice job...have you seen the videos where they use the same clamps you're using and instead of bolting across one rib...they place the u bolt diagonally across the point where the two ribs intersect and thereby put clamping pressure on both ribs at the same time . Not sure if that will still give enough pressure to pull the center of the ribs tight to the top since they will be more or less at the ends of the ribs where they intersect and not in between...hope that makes sense.

@melgross

Too many guys don’t understand that the top tab, slots are supposed to be TIG welded so that you don’t have to angle grind the welds down. If you need to practice TIG welding to get it right, then take the time. The table, if done right will last a long time, and if not done right, will also last a long time. But if not done right, it won’t be what it should, all that time.

@Moore257

I thought only the bottom was to be welded cause welding on the top makes it no longer flat. Even with grinding it’s not flat anymore…? Or am I missing something?

@jarexxsuvexx8212 3 года назад

I am about to buy this table but welding the table from the top and then using a grinder to smooth out the weld doesn't sit well with me at all. That table looks nice and smooth with just the tacking on the bottom. As a welding noobie i am really concern about accidentally overgrinding. 🤔I think what i will do is just put a bunch more tackies on the bottom and call it a day, lol.

@aerocam2 2 года назад

Great video! I’m about to pull the trigger on either this one or the 24” x 36” version. If you had it to do over.......what, if anything might you do different or suggest to someone in my place who’s about to order a table. Just as an FYI.....I will not be purchasing the leg kit as my top will be mounted to an electric lift table (with its own casters) that elevates from approx 20” to almost 48” in height with linear actuators and the flip of a switch so as to set the working height according to the task at hand. Any input appreciated and thanks again for taking the time to create this video for our benefit. Thanks