DIY FSi6 Simulator Cable 

I don't have any of those little pin connectors by themselves so I cut open the female end of a servo lead extension wire and removed one of the pins. I pulled the pin with the white wire out and used red for signal/black for ground. It was a little loose so I spread the pins out a little and it stays in there nice and snug now. If anyone can't find an s video cable or those little pin connectors, then you know what to do now. By the way...this is the best tutorial for DIY simulator cable I've found. Your instructions are very thorough. No one else has mentioned what pin on the controller is the correct one. My hat is off to you, brother!

Tip: 1) If SmartProPlus never connects to your transmitter then the most plausible cause is you are trying to insert the 3mm jack as shown in video to 3.5mm headphone jack in your laptop. The 3mm jack is detected as speaker. In order to use the 3mm jack in 3.5mmheadphone jack as microphone you need to 3.5mm headphone jack to microphone and speaker splitter. You can get it dirt cheap. 2)If your transmitter connects but the signal fluctuates too much then go to Manage your audio devices and then choose your external microphone and then decrease its level. The lower the level the more stable will be the signal. Hope it helps!!

You saved my 300 rupees thanks keep posting such stuff

This worked perfectly....amazing work! Thank you!

Greatly appreciated brother. Worked like a charm.

Excellent job buddy. Thanks.

Thank you, this worked!

thank you so much... great explanation...worked fine on my 3 in one jack

1:22 Check with ohm-meter, that there are no bridges (short circuit) between the wires. So, RED wire only connects to tip. BLK only connects to base, BLUE only connects to middle.

That is brilliant mate

I don't have S-video cable, very good idea to use 2 pole pin :)

Hey, I just did this and it still works thank you! Hope you are keeping well. God bless

Very useful. Thank you.

If we already have S-Video cable do we have to install the Netframework...?

work like a charm (flysky fs-i6x). and indeed you can control it with a microfone aswel. (even usb) but good luck making the right tones. (low voice seems to be throttle down)

so basicly you are saying that if i hookup a microfone to the headphone jack and shout in the correct tones i can control a plane in a flight sim?

Very good and helpful. When I tried my Flysky PPM to Mic input in windows 10 using SmartPropoPlus, the signals are flickering. Any reason ? And how to fix it. Appreciate it.

hello buddy , i did exactly as in video ,but the roll over and pitch sticks are not getting calibrated , speed and yaw stick works well , kindly advice

Hey bro you work awesome Please make a video that hoe to control brushed motor with flysky i6

should we still go into simulation mode with the radio?

you could just buy the FS-i6X for the same price or cheaper than the fs-i6 oddly enough. the data cable included on the FS-i6X worked perfect on clearview. I have heard from several sources you can update the firmware to effectively make your fs-6i an X model. Aswell.

Muito, muito obrigado!! Deu super certo!!!

Nice video

Good video. I love it

wht simulator softwares we need for this, could we use phoenix software .. bro?

hmm how about connecting it to the OTG cable to phone ?

Smartpropoplus does not recognize my old Hitec Focus 4, any idea? :(

Sir, Does the same technique works with other transmitters such as Avionic RGB6i which I have???

I've made a cable same as your video.. But the Smartpropoplus isn't detecting the tx.. Can I have any kind of help??

thankyou so much bro

Hello! PropoPlus is working fine, but PicaSim is not recognizing the joystick signals. What may be wrong? Thanks!!

Please make one video on how to make transmitter usb to ps2 trainer cable . There are no videos on RU-vid of that and many searching for that. I hope you wil get lots of views for that. So make it fast bro

Make Hand. Do you have SmartPropoplus? I can't find on the internet the software.

Thank you, sir!

Transmitter connected. But saying cannot feed position to vjoy device. And in picasim, after clicking joystick, it is saying no joystick detected or available. Please help me bro. 👍

thanks

How to check ground cabel using multimeter

Sir smartproplus software is not available pls help me

Do I have to power the transmitter by AA batteries or it will get electricity on its own from the pc through stereo cable?? Just asking to avoid any risk of something like shot circuit etc..😕😕

it works with my win 10 and reflex sim. but no airplane engine sim volume....if i turn up speakers i get a ping noise so loud it will drive u nuts. i have to fly with volume turned down. i just striped one end of the 3.5 stereo cable. And went direct in radio with ppm and a ground.ANYONE HAVE VOLUME???

Tks

you r amazing

Thank u soo much bro. I used it and was great. But after an hour it started not to working. Now when i connect it connect and disconnect again and again. I tried changing cable and pc and everything. Can u help me plz?

Will this work for laptop? Because when I tried it smartproplus was showing transmitter disconnected

bro provide link for smart propo plus link not working

Can we use in phone

Hey bro I just purchased fs i6 but I want to use it with fpv free rider on my phone please tell what should be the procedure

Smartpropoplus detects my controller. But when i start LiftOff the sim doesnt detect it, what am i doing wrong?

Bhai . Liftoff simulator ke bareme video banaona !

Please bro help me I connected everything as u told in the video and then I installed all the softwares including the Net framework . Then also when the connect the jack to my laptop and open the software it never connects and always keep fluctuating I am unable to connect I have checked my connections 1000 times and I am also not interested in purchasing a cable from banggood which will take ha huuuugge time to come

Is 'an old earphone 3.5mm plug' same to what you are calling a 'stereo cable'?? Can I use a earphone plug??

Sir are you have laptop or pc . If laptop then how many aux ports are there as in mine there are only onle jack for headphone not for mic thus I can't use it on my pc.

bhai recing drone training ka video banao

Omg it's working but download freeride that's a much. Better simulator 😁

The link doesn't work

How do you make a data cable for firmware updating?

My computer doesn’t recognize my transmitter as an external mic. It says that nothing is plugged into the jack. Any tips?

Making it at midnight

which app do you use for video edit?

my not working plz help

its not connecting with software

Compatible fs i6X ???

bro can we use normal headphone jack?? plz reply....and say which is stereo cable plz reply

My computer have only one 1 port for Head set (mic and head phones) :(

its not working any setting in controller need to be done

Whats the name of the cable in the right on 00:00

Can u use this with phone?

Can i use 4 port headphone jack

Is it working with freerider? Thanks advanved

Will this work with fs ct6b

estou com um problema, no meu fsi6 funciona tudo perfeitamente,mas tem horas que tos controles ficam tudo doido , como resolver? por favor.

Not working with my fkysky fsi6 10 ch moded

What did he say???

does it work with RF simulator?

so are you sure that this will works ALL lap tops and desktops.......hp pavilion needs a 4 way and the mic is and the opposite end of the plug.....

Fpv drone aaye gaa is simulator m

Verry nice i will also complete this couse some people have a problem with the connection on windows 10,they don't have a v joy 1 connection and this solve the problem,( is a copy paste from RC.GROUPS ) For those of you wondering how to get this working with any radio without the use of a USB dongle, download the application called "SmartPropoPlus" from www.smartpropoplus.com/site/ and install it. Hook your radio up with a standard 3.5 mm audio cable and plug it into one of your soundcard speaker ports. SmartPropPlus and vJoy will detect the PPM pulses and transform them into a joystick driver which can later be used with games etc. If you are running Windows 10 x64 as I am, the joystick emulator/driver doesn't work that comes bundled with the application. The solution to that is to install latest SmartPropoplus and ignore the failed installation of vJoy, then manually install vJoy "vJoy_205_050515.exe" from sourceforge.net/projects/vjo...atest/download which will upgrade the older vJoy installation. After the installation is succesfull, follow the below workaround: Copy, paste and replace the following files from C:\Program Files\vJoy\x64 to C:\Program Files\SmartPropoPlus folder: msvcp120.dll msvcr120.dll vJoyInterface.dll This should now make it possible to map input from SPP to vJoy. Now check your "Set up USB game controllers" in Windows and hopefully you should see the "vJoy device". Calibrate your controller and then set up your radio in FPVFreerider. I recommend "use deadzone"

Is it work mobile????

Not working

The channel don't line up correctly..sim is not playable..plz help me..need a offset dll..I can't find it anywhere

All channels have higher value numbers

if the SmartPropoPlus link does work....try this link.. sourceforge.net/projects/smartpropoplus/

Can you understand this dude? 4:10 WRONG... why didn't he solder yellow/brown leads directly TO the male-to-male header and eliminate the JR connector entirely? This way, it's easy to LOSE the damn header in the carpet and there's an extra break in the connection that doesn't need to exist!

Not working