DIY Roomba for Desk and Countertops

Подписаться 577

Просмотров 14 тыс.

50% 1

Fully 3D printed robot you can put on any table to remove that pesky dust and dog hair. This project was built off of the SMARs robot on Thingiverse. If you want to build one for yourself the links can be found below. Stunts in this video were performed by professionals. Batteries not included.
GitHub: github.com/jareddilley/Desk-R...
Reddit: / jareddilley
Patreon: / jareddilley

Наука

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@A5omic 10 месяцев назад

No more need for the maid now. Genius.

@VictorDeLeon-rw2du 9 дней назад

Im building the Cosmarz robot rn why didnt i think of this!

@kenlin3934 Месяц назад

very good

@MechAero_Labs 7 месяцев назад

Bro you just got yourself a subscriber ❤❤ keep on creating

@Sanic3750 10 месяцев назад

Your audio is fine bro and nice robot

@PotatoNachoIT 10 месяцев назад

sick. keep it up.

@davidlau6668 9 месяцев назад

Hi Jared, Zhan here, super cool video!!

@henryhancock7396 10 месяцев назад

More attachments needed

@uduakobioh6113 6 месяцев назад

Hi, nice vid How did you join together the links on the chains around the wheels

@jareddilley 5 месяцев назад

Cut up pieces of filament worked for me

@HJM9x 10 месяцев назад

I need this

@harshadkakad2669 9 месяцев назад

I aslo need thise😊

@MIDHUNMATHEW-mb4kz 6 месяцев назад

Is there any tutorial on how to make? Also which motor have you used?

@jareddilley 6 месяцев назад

N20 3-6V motors and the GitHub has most of the details

@prashanttiwari8873 5 месяцев назад

how you attchech the ir sensor , the file on the git do not have a mount for ir sensor , plese provide stl for that

@jareddilley 5 месяцев назад

There is a mount on the front used for the ultra sonic sensor which stick out on both sides, that’s is when you can screw in the IR sensors

@guardianpresencerobotics7776 7 месяцев назад

try rfid or if battery low wifi rssi when in range rssi line following printed line grid onto dock esp8266

@kaiyen2210 7 месяцев назад

Did you use female to male connectors for the sensors? and not have to solder anything on the motor driver? btw i subscribed, neat little robot

@jareddilley 7 месяцев назад

Correct female to male, I still had to solder the male pins into the motor shield

@gioelebressan8829 5 месяцев назад

What motor, sensor, regolator I must buy for build this?

@jareddilley 5 месяцев назад

Arduino uno, HiLetgo L293D motor shield, 2 6V 150rpm N20 motors, and 2 3-pin ir sensors

@happytazer2709 9 месяцев назад

I couldn't find the prefit size of the chassis. Can you help me with that? Please

@happytazer2709 9 месяцев назад

In mm

@jareddilley 9 месяцев назад

The model is x10 bigger then it should be for some reason, reduce to 10% for scaling

@jareddilley 9 месяцев назад

I’m Cura after scaling down to 10% it gives these dimensions: 78mm x 70mm x 33mm

@Daruma_Studio 10 месяцев назад

Uh oh... voice is quiet again... Excited for the video content though...

@Daruma_Studio 10 месяцев назад

Yeah just finished watching the video. Love the content. Fun editing. Tons of potential in this channel... but the audio is all sorts of fucked still. You gotta do some focus on the audio in editing! Im an audio engineer and Im happy to zoom with you to show you how if you're interested? (free of course, just helping out)

@jareddilley 10 месяцев назад

Agreed, but at least is consistent in volume, definitely an issue from editing on my ipad

@Daruma_Studio 10 месяцев назад

@@jareddilley Oh yeah definite improvement from the last video. Which in itself will be fun to watch your editing and audio mixing improve just like your projects. Looking forward to more!

@guardianpresencerobotics7776 7 месяцев назад

what about a power docking station

@jareddilley 7 месяцев назад

Great thinking, it doesn’t have location tracking so would have to figure that one out