No video :(

DIY Tensioner Pulley Replacement 4.2L Ford F-150 (Screeching Bearings & Squealing Serpentine Belt)

Подписаться 10 тыс.

Просмотров 31 тыс.

50% 1

HOW TO DIY Replacement of the 2000, 2001, 2002, 2003 etc Ford f-150 4.2L V6 Tensioner Pulley that makes a loud screeching, squealing, squeaking sound. I approached this automotive repair as a diy'er who might have limited tools or a diy'er who wanted to make the repair with minimal disassembly .
many videos suggest taking apart your covers, fan guard, air assembly, fan & serpentine belt to access this tension pulley but that's not necessary . In this video we remove the Alternator and access the tensioner in no time
Tools used Gearwrench 24" Long 1/2" drive breaker bar, Stanley 1/2" drive 12 point 15mm , 13mm sockets, Gearwrench 1/2" to 3/8" reducer & 13mm deep 6 point socket , ‪@LisleCorporation‬ 3/8" drive T50 Torx socket , @michaelpro 3/8" drive locking indexing ratchet, ‪@harborfreight‬ 1/2" drive Pittsburgh Pro Flex head ratchet, Craftsman long picks/Hooks, wire brush, 8mm & 10mm sockets for the battery and the parts used were ‪@DaycoOfficial‬ tensioner pulley & serpentine belt from Car Quest
Hopefully this video helps you out .
You Make Repairs at your own risk, nobody is liable for your faulty repairs, damage or injury but you.
I am a Mechanic & Tradesman, I do tool reviews, show tools in action doing real world repairs ,tool store tours, performance reviews, boat repairs, industrial machine, commercial equipment repairs & more
I'm on RU-vid, Facebook, Instagram, Tiktok & Rumble. Go follow. like, share, ring the bell and subscribe
here's one from my channel
Michael Pro 3/8" Drive Low Profile 20 Piece Tool Set #MP001001 ( First Impression Preview )
• MICHAEL PRO 3/8 Drive ...
Gearwrench 3/8" drive 90 tooth Long handle ratchet #81264T Performance review on RUMBLE
rumble.com/vfr...
How To Replace a Resistor on a Chevy Express 3500 DIY
• How To Replace a Resis...
MAYTAG CENTENNIAL Gearcase , Shaft & Hub Replacemnt DIY
• Maytag Centennial #MVW...
How To DIY replacing front brakes & rotors 2008 Toyota corolla (real world repairs) #mobilemechanic
• How To Change the Fron...
GEARWRENCH 3/8" Drive 90 Tooth Long Handle Ratchet Performance Review on Model - 81264T
• Video
KOBALT ELECTRICIANS TOOL HAUL (Non Contact Voltage tester, 9 pocket pouch & 1000 Volt Insulated screwdrivers)
• Video
How to diy Front Light Bulb Replacement Chevy Silverado
• How To Change the Fron...
How To DIY Change a Oil Filter Adapter Gasket on a 07 Chevy Uplander #MobileMechanic
• Replacing Oil Filter A...
How To DIY REPLACE TAILGATE HANDLE 2002-2003 FORD F150
• New Tailgate Handle Re...
How To DIY - Replace Trailer Mirror On A Chevy Express Box Truck #mobilemechanic #servicecall
• HOW TO Replace a Trail...
How To DIY - Oil Pressure Sensor Location & Replacement 2007 Chevy Uplander
• 2007 Chevy Uplander Oi...
TEQ PRO 84 Tooth 3/8" Long Handle Low Profile Flex Head Performance Review (rebranded Gearwrench) Model 81219
• TEQ PRO 84 Tooth 3/8" ...
Gearwrench SAE/METRIC REVERSING RATCHET WRENCH SET REVIEW (DEAL ALERT)
• GearWrench (DEAL ALERT...
Pittsburgh Pro Striking Cap Gasket Scrapper & Tire Iron Review
• Pittsburgh Pro Strikin...
Bad Bearings & Broken Shafts -A Day in the Life of A Tradesman (Tools in action-Pittsburgh Pro, Jobsmart, Stanley)
• Bad Bearings & Broken ...
#Dayco #89260 #260 #Tensioner #pulley #tensionerpulley #4.2L #ford #f150 #michaelpro #gearwrench #stanley #lisle #tools #craftsman #DIY #howto #kobalt #repairs #truck #serpentine #serpentinebelt

Опубликовано:

23 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 37

@danmac9423 Год назад

Thanks for the easy diy video and especially for the 2wd 4.2 those videos are hard to come by. This helped a lot, man. Keep at it!

@kawh8719 2 года назад

Man, thank you for the DIY prospective. I'm going to use this tomorrow as my guide and I'll let you know how it goes!

@themegaforce810 Год назад

Well, how’d she go 😂

@nameless-og Год назад

@The Megaforce RIP Kawh 😥

@roncharles4318 2 года назад

Thank you! My 2000 is whining bad…I’m going to use the method you showed!

@mr.artdepot3626 Год назад

Great Footage, Views, and Description Sir ! Damn Serpentine Belt Snapped with a Full Heavy Load on the Truck 🙄🙄🙄👀😁

@ErnestStallings Год назад

Thanks this was so helpful. I didn't have any problems as I followed your directions

@VIDSTORAGE Год назад

all idler pulleys with tensioner is the best thing to do .Dont over tighten that bolt for the tensioner ..I nearly stripped mine because the bolt was a bit froze from a small bit of corrosion ..I wanted to be sure it was tight ,it kept spinning ,it would not tighten ,so I put grey Teflon tape on the threads at that saved the day ... I took my fan clutch off and got the shroud out of the way and it made the job much easer

@vilcermolina6474 Год назад

Excellent video Master, congratulations from Caracas-Venezuela

@davidraborn3654 4 месяца назад

Thanks Bro, just got one for 100$ , just squeals. Will try running without belt for a minute to see if it's a bearing, hopefully just tensioner.

@mineonly2563 Год назад

Excellent video and commentary Even the make the tools great again slogan 😅😅

@kman2895 2 года назад

Good video thanks. Will be doing the pulley below the tensioner pulley, and more directly under the alternator soon as it has seized up and broken the serpentine belt. Hoping that pulley also has the torx socket , fingers crossed..

@rondallethco7486 Год назад

Wow I needed a new alternator and did it just like you showed me, thanks alot it worked well.

@user-wv7tb6wp5w Год назад

Hey brother i wanted to say thank you for your easy to follow back yard jerkem video . Awesome man im hooked im a new subscriber . Keep up the good work brother ..... apperciate ya more then u know!!!!

@cabinbills6743 3 года назад

Good job brother exact info i need . Mine is squealing when i start it then settles down . Know what to look for now

@albertsimmons8076 Год назад

THANK YOU SO MUCH FOR MAKING IT SO SIMPLE 😊😊😊😊😊😊😊

@obfuscated3090 Год назад

Worth noting is some less expensive tensioner pulleys like the Linerts I just bought aren't as wide as stock but are wide enough and stay centered on the belt. Smart play with tensioners and pulleys is bring your old ones when buying at the auto store. I removed the (LEFT HAND THREAD) tensioner pulley bolt so I'd have the bare pulley in hand for comparison to be sure I had a correct match.

@kingtrap1267 3 месяца назад

Easiest way for me was to pull it from bottom

@isaacbarrett9212 2 года назад

Thank you. Very helpful.

@genzisgod4930 7 месяцев назад

You are great. Thank you brother.

@JesusRamirez-mx7ti 6 месяцев назад

Thanks good video

@Sourivanh1 Год назад

Excellent video. Thanks for sharing

@jimo680 2 года назад

THANK YOU !!!! Excellent vid.

@chrissample3047 Год назад

I just took off my tensioner thanks. For tips

@J1SMOKES 2 года назад

I changed this in a 2000 f150 4.2 because of a rattling sound in drive at idle. Didn't get rid of the rattling but its for sure coming from the tensioner. Its out of warranty so I'm going to try again with the one you suggested.

@nickwheeler1652 2 года назад

I got an 07 4.2 and it's making a rattling sound when I turn on the AC at idle it's getting pretty loud. Hoping it's not something else on the belt did you seem to fix yours

@J1SMOKES 2 года назад

@@nickwheeler1652 it ended up being the belt. I just needed a new belt, the old one was stretched causing the tensioner to rattle because of lack of tension

@nickwheeler1652 2 года назад

@@J1SMOKES wow awesome definitely going to try that first thanks for the reply man. This rarely happens when somebody does grab yourself a cold one and no that you really help the guy out on the interweb

@danieldeilgat7558 7 месяцев назад

Thanks for the video. One question. My belt tensioner won't budge when I try to release the pressure, any idea why?

@jimo680 2 года назад

What if I just want to replace the pulley only? Is that center bolt a reverse thread; and, is there any con to just replacing the pulley only? Great vids. Thanks Again, You really helped me out.