Тёмный

Don't Regear Your Jeep Until YOU Watch This Video! 

Cherokee Ronnie
Подписаться 36 тыс.
Просмотров 10 тыс.
50% 1

What Does a New Set of Gears Do?
One of the most common modifications done to Wranglers is installing a lift kit and a larger set of tires. Something many people forget about when they install a larger set of tires is the drivetrain was geared to provide a balance between torque and top speed. When it comes to gear ratios the higher the number the more times the driving member needs to turn. For example, the first gear on an AX-15 transmission has a gear ratio of 3.83:1 and fifth gear has a gear ratio of 0.79:1.
Gears with lower numbers are referred to as taller and higher numbers are referred to as shorter. Taller gearing provides a higher top speed and better fuel economy while shorter gearing provides more low end torque and better acceleration. Taller gearing is better for daily driving especially if you are planning on doing a lot of highway driving or are simply going to run small tires. Shorter gearing is needed for large tires and also aids in rock crawling by increasing low end torque.
How Does Gearing Work?
The gearing of your axles is set by the number of teeth on the ring and pinion gears. This determines how many times your driveshaft will have to rotate to spin the wheels once. A 4.10:1 gear ratio, for example, would mean that your driveshaft would have to spin 4.10 times to spin the wheels once.
The stock gear ratio tends to vary depending on the year and package your Jeep has. Some of the possible ratios include 3.07, 3.55, 3.73, and 4.10. Wranglers that are equipped with the Rubicon package typically come with the 4.10 gear set in their Dana 44 axles. The chart below shows the relationship between gear ratios and tire size. The numbers across the top are gear ratios, the numbers down the left side are tire sizes in inches, and the 4 digit numbers in the white boxes show RPM.
Why Should I Regear?
If you do a lot of highway driving on small to mid sized tires, it may be practical to regear to a taller setup to increase your top speed and fuel economy. If you are planning on doing a lot of off-roading or are only upgrading to a larger set of tires, you should probably install shorter gears.
When larger tires are installed, you have several things working against you: the diameter of the tire, rotational mass, rolling resistance, and the added weight of the tires. The diameter of your tires directly affects how hard your drivetrain has to work in order to move the vehicle, what you need to keep in mind is the axle is going to be turning your wheels. The axle shafts are just over an inch in diameter, and they have to turn whatever tires are on your Wrangler. This means that with a 30 inch tire you need to apply 30 times more force to the axle in order to turn the wheel. By regearing to a shorter gear, you will increase the amount of force that is being sent to the axle, this allows your Jeep to move the tires with less of a strain on the engine.
How Much it Costs to Regear Your Jeep
Replacing your Jeep's ring and pinion gears is more than simply purchasing a ring and pinion set. There are a number of bearings, seals, bolts, and the differential cover gaskets to worry about. If you're replacing the gears in both front and rear differentials, your overall cost will be understandably more. An entire gear overhaul kit will run you anywhere from $600-$1,200.
Certain differentials can only accommodate certain size ring gears. Generally, the higher numerically you go in gears, the bigger the ring gear. Should you need to upgrade the differential's carrier, this is the time to decide if you want to upgrade to lockers. No reason to do the work twice should you decide on lockers later. A new differential carrier will run about $700-$1,000.
Labor will always vary by region and shop, but you expect a ring and pinion gear installed to be approximately $500-$700 per axle. The being said, a complete regear job is several thousand dollars, done properly.
Buy a shirt 🤘🏻
cherokee-ronnie-store.creator...
WV Off Road Club groups/11701...
Buy shirts here teespring.com/stores/cherokee...
Cheap Cherokee build • cheap cherokee build
Facebook profile.php?...
My guitar channel / ronaldleggettjr #jeepwrangler #jeepxj #jeepjk

Авто/Мото

Опубликовано:

 

5 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 65   
@Lray4x4
@Lray4x4 Год назад
I have installed several sets of USA standard gears and never had a problem, including the ones in my XJ on 35s that I have beat on for 4 seasons. Revolution gears are good as well. As far a regearing goes it's really not that difficult to do just time consuming, patience is key.
@Mr2greys
@Mr2greys Год назад
I did a 8.8 and HP D30 swap with ARB lockers in my TJ and did it all myself. At that point Revolution didnt exist yet so I had no real choice other than Yukon, they have been fine but that was also 10 years ago. Regearing isn't difficult but it is timeconsuming, when I did it I used Billavista's regearing Bible which was the go-to guide at the time.
Год назад
would love to see how you regear! :)
@sirthrival4601
@sirthrival4601 Год назад
I'm watching your videos, and this is EXACTLY what I am needing right now! Thank you for making these ideas and videos available, it's all good common sense, keep it up!
@Derick_Mn
@Derick_Mn Год назад
would appreciate re-gear video. thank you for sharing your thoughts and experience in this video
@rustygehl
@rustygehl 13 дней назад
Yep, lol. Spent money on 31's and a stroker engine and now I need 4.10's, the regear wpuld cost me more than my Stroker, Clifford intake and Holley 390 DP combined!!! Nope, gonna buy spare axles and regear. Keep the old incase I screw something up, lol.
@paulresca6681
@paulresca6681 Год назад
Great video and information. Would love to see the re-gear video. I didn’t rebuild my 30 because I got intimidated by the shims and crush sleeve I still have the axle and would love to build it. Thanks
@bryanstrietelmeier2573
@bryanstrietelmeier2573 Год назад
Excellent, looking forward to your regear tutorial!❤️💯
@ThatGuyFromArizona
@ThatGuyFromArizona 3 дня назад
Nice job Ronnie.
@Robert-di7xn
@Robert-di7xn Год назад
Yes let's see a re gear video.. either way, gotta get mine re geared.
@seanjhonson6441
@seanjhonson6441 11 месяцев назад
Awesome video, thanks for sharing all that information!
@Wanderer_XJ
@Wanderer_XJ Год назад
My USA Standard regear has whined since day one. When coasting, it sounds like a fire engine siren. 😆
@Moezer
@Moezer Год назад
Got my gear set on my jk rubi from 4wp g2 gears 4.88 no issues running 35s also got their worry free warranty even if u trash them they will cover every thing for 3 years and you got an option to extend that warranty after wards no worries here
@ky0611
@ky0611 Год назад
You would make a good simple regear video
@Skiridr22
@Skiridr22 Год назад
There’s allot of places that will actually rent out some of those special tools.
@dustytrailscactusron
@dustytrailscactusron Год назад
Yes, please do a re-gear video.
@LinusScrubTips
@LinusScrubTips Год назад
Thanks. Revolution makes a kit for my Comanche (rev d30 and 8.25). $619, good deal!
@boydshands3660
@boydshands3660 Год назад
Great video! What gear you recommend on a dd xj with 4.5 lift and 31" tires? I have ax15 manual transmission.
@cherokeeronnie
@cherokeeronnie Год назад
I would run 410s but that’s if you plan on staying with 31 inch tires
@ky0611
@ky0611 Год назад
That's crazy when you think about it though, yukon is probably the biggest name in gears and your saying they suck lol
@cherokeeronnie
@cherokeeronnie Год назад
That’s why everyone don’t like me I go against the grain and speak the truth lol I’ve never had good luck with them when it came to gears
@AustinH7
@AustinH7 Год назад
I can confirm Yukon does suck!
@ky0611
@ky0611 Год назад
@@AustinH7 that's actually really good to know cause the place by me carries yukon, motive and revolution. I was like I want yukon! Lol I guess not anymore
@timheffron5849
@timheffron5849 Год назад
Ronnie where are you located? I know you are a fan of folks doing their own work but I am not mechanical at all! The trouble is I live up in the Seattle area and don't know of a good reliable shop. Any advice you can provide will be very much appreciated.
@mfunes1494
@mfunes1494 4 месяца назад
I have a 2002 Jeep TJ Sahara with 3.07 gears. To do both front and rear with lockers I have been quoted $4k-7k to regear to 4.56. With the 3.07 I would need a new casing.
@ghernandez6457
@ghernandez6457 3 месяца назад
My shop uses yukons and they never had a customer return for bad regearing, nothing but good reviews and they wheel the hard stuff all over AZ and Moab. I wonder if what the shops and the diy people get are completely different.
@paulmosher2013
@paulmosher2013 Год назад
Re-gear video please, Ronnie
@TwoFeatherChannel
@TwoFeatherChannel 6 месяцев назад
I recently contacted a semi large shop with Axle in their name, about regear for my JLU Rubicon. told them I wanted 5.13's front and rear with master install package. they said they don't do master installs with regear, it will be Ring and Pinion Gear only, Price of $3,500. to $4,000+ and a 2-3 day job. First off I want new Bearings and Seals if someone is going messing around in there, and they say they don't replace with new ones. Second, they are a shop with several bays and they are going to tell me it takes 2 to 3 days to replace 2 Ring and Pinions only.
@gryffydd42
@gryffydd42 Год назад
Id like to see a regear video also. If possible , at least verbal description of dealing with Chrysler 8.25 would be appreciated. It looks like it uses some internal thing to adjust backlash instead of shims behind bearings.
@crashtke
@crashtke Год назад
They are actually much easier to get backlash in my opinion. No pulling, shimming, pulling, shimming over and over again. Just adjust, lock down and you are good.
@jeremyhanna3852
@jeremyhanna3852 8 месяцев назад
Can someone please explain the carrier thing my xj has 355 gears and I'm going to 488 have not went parts shopping yet
@PoorManOverland
@PoorManOverland Месяц назад
And that’s funny how you say that that’s the third thing you should think about and that is the third thing I’m thinking about is regearing but I am not paying $3000 for a simple 488 regear so it looks like I’ll be doing it myself. I do everything else on my jeep. I’m sure I can do this. I did the rocker arms and lift kit so looks like I’m doing a regear
@davidrockville7889
@davidrockville7889 Год назад
Great video! Planning on ordering a 24 Rubicon 4 door, with 35s, 3.6L, will put on roof top tent and maybe tow a couple of times a year. Should I go with the 4.56 or get 4.88 option from factory?
@cherokeeronnie
@cherokeeronnie Год назад
You highway drive?
@davidrockville7889
@davidrockville7889 Год назад
@@cherokeeronnie I do, it will be my daily driver as well.
@CrucesNomad1
@CrucesNomad1 7 месяцев назад
Darn dude,, took ya 9 minutes to get to your prefered gears lol. Great video though. I'll be looking at my gear sets now.
@TxHylyner
@TxHylyner Год назад
Love the videos and info. Would like your opinion on what I should go with in my WJ. 2004 4.0 currently on 32s with factory 3.55s. Highly unlikely but possibly 35s in the far distant future. Jeep is built around running a 33 though. Running the numbers I’m seeing 4.10s but have been told “you can’t have too much gear”. Jeep sees allot of sustained highway driving and I’m afraid 4.56 will be too low for normal driving. Any help is greatly appreciated. 35/30 Dana. Good source for complete gear set to complete the job?
@cherokeeronnie
@cherokeeronnie Год назад
Go with 410 if your not really serious about 35s and actually there is a thing as to much if you run smaller tires with 456 it scream on the high way with the rpm’s
@TxHylyner
@TxHylyner Год назад
@@cherokeeronnie complete gear set and refresh recommendations? Wheel bearings etc. Jeep does see off-road trail use but its finessed not bashed.
@AnglinTexas
@AnglinTexas Год назад
I’ve been considering regearing my wife’s JKU Rubi. I’m running “35s” (315/70/17) with 4.10s and it drives fine, we don’t do much off-road but we tow a heavy popup a couple times a year and engine temps tend to climb. I’ve got nothing in front of the grill and a Mishimoto radiator and still have to go real easy to keep temps under 240. I’m thinking a set of 4.88 will help.
@cherokeeronnie
@cherokeeronnie Год назад
I don’t recommend 488 for that plus the temps reaching the high is another issue I tow with mine and I only see 234 than it drops quick. 488 will have your rpm’s screaming
@AnglinTexas
@AnglinTexas Год назад
@@cherokeeronnie how much are you towing with those temps? I’m towing right at the limit of what it’s rated for (3500 lbs). The chart I referenced shows 435 RPM increase from 4.1 to 4.88 being 2750 RPM at 70.
@cherokeeronnie
@cherokeeronnie Год назад
I was right at 2900 pounds
@AustinH7
@AustinH7 Год назад
Word of warning for those who want to do a regear themselves, I tried myself, but the gears were extremely noisy, even with a good pattern and backlash. No warranty because I did it myself. Was shit out of luck… Also do not buy Yukon gears! Those might have been why they were so loud.
@cherokeeronnie
@cherokeeronnie Год назад
Yeah out of my experience Yukon are loud don’t think it was your setup bud
@Wanderer_XJ
@Wanderer_XJ Год назад
What noise did you get? I’ve had a loud whine on my USA Standard when coasting since day one of install. Not sure if it’s the parts or the setup.
@crashtke
@crashtke Год назад
My Yukons are just fine.
@AustinH7
@AustinH7 Год назад
@@Wanderer_XJ could be both. A deceleration noise can be a loose pinion I believe. I have a noise on acceleration which I believe is an issue with the ring and pinion itself
@PoorManOverland
@PoorManOverland Месяц назад
These dude around here in southern Indiana are trying to charge 2900 for a simple 4.88 regear on my jk smh
@ky0611
@ky0611 Год назад
Best locker video !?
@Lray4x4
@Lray4x4 Год назад
Detroit Locker or Yukon Grizzly.
@ky0611
@ky0611 Год назад
@@Lray4x4 I hear detroits blow out the carrier?
@Lray4x4
@Lray4x4 Год назад
@@ky0611 anything can break but they aren't weak by any means, you might be thinking of a lunchbox locker that goes inside a factory carrier. The Detroit and Grizzly are both full carrier lockers and the strongest on the market. Only thing stronger would be a spool but that isn't a locker.
@kkesj1263
@kkesj1263 11 месяцев назад
Is regearing needed if I don’t off road but I do have 35in?
@cherokeeronnie
@cherokeeronnie 11 месяцев назад
Yeah it will give its power back like it was stock
@Daddyoscatio
@Daddyoscatio Год назад
I just got a set of USA Standard. I ordered them just days before this video. now I'm going to return them.. can't find the usa made sets I need..
@cherokeeronnie
@cherokeeronnie Год назад
Revolution gear is by far the best budget gear I been using
@Daddyoscatio
@Daddyoscatio Год назад
@@cherokeeronnie and that's why they're out of stock 😢
@ninjascout468
@ninjascout468 Год назад
My Xj is still at 354 lol I can't afford to regear my Dana 30/35 abs ex-military 93 model & I'm on 33" Mt would love something better if anyone has some old good 456 gear set up cheap hit me up please , I use 4lo just too be able to climb stuff
@crashtke
@crashtke Год назад
I have some fronts super cheap. Yukon 4.56. They only had 100 miles or so on em and I did not like the front locker. Place said they would not do the new locker without replacing the gears.
@nevamind932
@nevamind932 Год назад
Where are circle k gears made
@cherokeeronnie
@cherokeeronnie Год назад
Korea
@hakenkreuz7076
@hakenkreuz7076 11 месяцев назад
Great ,getting Yukon 4.88's installed right now. Why would any 4x4shop shop use Chinese crap? Wish I would have known this before. The Yukon (4.88) "whine" seems to be an issue.
Далее
MC TAXI: АК-47
35:14
Просмотров 469 тыс.
Какую одежду я не ношу? 😱
00:13
Просмотров 444 тыс.
Choosing The BEST Axle Gear Ratio
18:07
Просмотров 65 тыс.
How to Regear your jeep XJ/JK/JL/JT/ZJ/WJ
20:37
Просмотров 15 тыс.
The NEED to know on Jeep ReGearing
7:48
Просмотров 2,4 тыс.
What are lockers? Which one is best??
21:06
Просмотров 504 тыс.
WHAT YOU (ACTUALLY) NEED TO RUN 37s ON YOUR JEEP
16:47
Просмотров 333 тыс.
Pinion Depth Checking With Simple Tools
31:23
Просмотров 70 тыс.
How to Re-gear a Dana 30
43:01
Просмотров 171 тыс.
The Sidi Rex Boots🔥 #motorcycle #racing #shorts
0:14