dr PULLEY roller EXPLAINED, why ANKLED? / & faster than MALOSSI? | FMP-Solid PASSion | 

*I had to replace all the 'moving bits' and some that don't, like the 'Guides' for the backing-plate on my '08 'Metropolitan CHF-50/S and replaced the clutch-pads and springs with 'Honda' parts...and ordered a 'Prima' roller-weights pkg. @$40+ S & H* *The 'Dr. Pulley' sliders looked as-if they had some 'wear' with scuff marks on them, so I installed the 'rollers'* *WHAT A MISTAKE!* *For almost 4-yrs. I consistently had a 42-mph top-end and 'nailed the speedo' on downgrades...then problems began and speed dropped to 28 with 'funny noises' to go with it* *I looked at vids, and diagnosed 'wtf is wrong?' and ordered new stuff right away, and a new Kevlar belt because I had no idea how many miles were on it* (I kept the old one for an 'emergency spare') *The nearest Honda shop is 60-miles away, and I can't afford a '$95 an hour' shop-rate at a 3-hour minimum, so I did everything myself, as always* (*My scoot already had numerous 'upgrades' when I bought it, so I was very happy w/the performance I had from an 'almost stock' engine etc. so I left everything alone other than normal maintenance* ) *I wound-up installing the '3gm x3 and 9gm x3' because anything heavier meant no 'grade-climbing' at all unless '5mph' counts as 'climbing'* *I'm 'locked-in' at 38-mph!* *And there is a 'hiccup' at 31/32 -mph where it surges up and down that I can't figure out* *Moral of Story?* *I spent time/$$$$/and aggravation for a 'tuning roller kit' THAT SUCKS!* *I'm going to order 'Dr. Pulley Sliders' and replace those PH*KING ROLLERS with what I had to start with that worked fine with 'no problemas' at all!*

The sliders work pretty good for me very smooth acceleration

Honda Varrrriatorrr 😂 gut erklärt 👍

Good laugh at the end!!

I see the difference about what kind of benefits?

Did u lost any top sped ? my burgman has 21gr original should i go with the same weight pulley or gram lower ? i dont want to loose top speed

Can you please tell me if you bettered the fuel usage. I am thinking of mounting the dr pulleys in my original SH300 2013. I know have stock 19 gram rollers. I would like the rpm to go down on the highway.

Hello very interresting see you later 👍

Don’t you think that the greater contact area will lead to more friction between components?

hi .. is it ok to combine 3pcs dr pulley slider and 3pcs round roller??

My 125cc uses 14gramm rollers when i put replacements from yamaha same weight my scooter dies 😂 dont know why. Which weight shall i order from dr.pulley? Want fast pickup and dont want to lose top speed

Will malossi variator+dr pulley sliders will be better

Hi dude, i wanna ask, after a long time use sliding roller, any complaint ? It's been 5 years since this video, can you give me pro and con, because i wanna try this too. Thank you, i hope you can reply my comment

Can you install rollers en slider at the same time

Whats better malossi or dr pulley?

🤘👍might do job not confident like

Johnny Depp is that you???

The windshield and the weight off the biker's makes the different

What is "Malossi MHR"?

What?! Why get all that Malossi stuff?! Thanks, you just saved me several hundred $.

Hows the performance of the rollers?

is it compatible for the racing pulley??

how many grams the Dr. Pulley weight ?

Oooooooh angled...!

You talk funny