Easy Exhaust Pipe Repair Without Welding!

Подписаться 498

Просмотров 19 тыс.

50% 1

Repairing part of the tailpipe on my 2008 Infiniti FX35. This can be done on any exhaust pipe using the same tools, parts, and methods. Be sure to measure your exhaust pipe outside diameter and make sure you get the appropriate size couplers to fit. I use digital calipers for this, I'll link those below as well. This video is for entertainment purposes only, be careful any time you use a reciprocating saw!
2.25" OD Exhaust Pipe
amzn.to/48oN4di
2.375" to 2.25" Exhaust Couplers 2-pack
amzn.to/3I9Sq1t
Muffler and Tailpipe Sealer
amzn.to/3URFKUc
Reciprocating Saw
amzn.to/3TaFwXf
Digital Calipers
amzn.to/42V2gxr
*These are Amazon Associate links, meaning there is no added cost to you but a portion of the sale will go to support my channel.
Disclaimer:
Wrench on your own vehicle at your own risk. Ben Wrenchin' doesn't recommend all the methods used in this video. In fact, some of the methods in this video should never be used at all. EVER. Be smart and safe. Ben Wrenchin' is not responsible for injury resulting from performing actions found in this video. This is only to serve as entertainment purposes and is not meant to be used as suggestion or instruction for how to perform any of the actions contained in this video.
0:00 Intro
0:54 The Problem
1:58 Cutting The Old Exhaust Pipe
2:25 Parts Needed For The Fix ~$40
3:19 Measuring And Cutting The New Pipe
4:00 Installing The New Section Of Pipe
6:56 Describing Why I Did It This Way
11:31 The Results - It's Wife Approved
11:50 Outro - Please Subscribe!

Авто/Мото

Опубликовано:

3 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 55

@jayone7437 3 месяца назад

That’s a very good repair. When you cut the pipe on the back section I noted the pipe had good thickness through out its circumference. Don’t be surprised if it lasts a good time longer.

@benwrenchin 3 месяца назад

I'm hoping it will. Unfortunately water collects right at that section, so I think no matter what it's not going to last forever. Still, for $40 if it lasts a year or two I'm fine with it, and I expect it could last much longer.

@leodeboca Месяц назад

good job!

@benwrenchin Месяц назад

Thanks Leo! Appreciate it 🙏

@avery214j 3 месяца назад

Good Job Man. Saved yourself lots of $$ excellent job.

@benwrenchin 3 месяца назад

Thanks 👍

@christophernalbone6299 3 месяца назад

You could buy a exhaust pipe expansion tool and use the sealant with 2 u clamps. Good tool to have since you have the mechanical ability. Anyway very good video.

@benwrenchin 3 месяца назад

Thank you, I've seen the expansion tool but I don't like to have too many specialty tools if I can help it. I'd rather just borrow one of them using the Loan-a-tool at AutoZone whenever I need something like that.

@victorvillasana3409 2 месяца назад

Good repair, that’s the way I’d do it. If some of you people can get it done for “$35” do it your way. But there is a satisfaction to fixing stuff yourself at your own schedule. Rather than waiting in line at a muffler shop. I would suggest adding some high temp paint to the whole repair just to make it last longer.

@benwrenchin 2 месяца назад

Great tip! Thanks Victor 🙏

@megs4898 3 месяца назад

Gracias gracias gracias

@benwrenchin 3 месяца назад

¡De nada!

@stevewheatley243 3 месяца назад

Looks good to me. And those band clamps work great. They're on my car.

@benwrenchin 3 месяца назад

Thanks, the clamps do hold up surprisingly well. The old one that I took off had been on for a year or so and wasn't in bad shape at all.

@stevewheatley243 3 месяца назад

@@benwrenchin They won't rust out. They may outlive your car.

@benwrenchin 3 месяца назад

@@stevewheatley243 My biggest concern is the existing pipe rusting on the back end, but I can always repatch it with the extra length of pipe I have left.

@stevewheatley243 3 месяца назад

@@benwrenchin You should be able to reuse those clamps too. Mines been on my car 2 yrs and they're still good.

@benwrenchin 3 месяца назад

@@stevewheatley243 Did you put exhaust sealer on them too?

@alan6832 3 месяца назад

As long as you're well behind the oxygen sensors, heavily coat the exhaust, inside and out with silicone spray or tire shine to prevent further rust on already rusted pipes. Then you can send some silicone further back by using extra on the inside, then start and rev the engine while it is still wet to protect the inside of the pipe farther back. I like your choice of clamps and am considering using similar clamps myself, where did you get them? However I might have kept in mind that the undersides of cars do have aerodynamics, so I might have rotated the lower clamp to reduce drag. I'm considering similar methods myself to avoid dealing with rusted on bolts and sleeves as well as having to remove the transmission crossmember. I don't have one of those saws though.

@benwrenchin 3 месяца назад

I got the clamps on Amazon, links are in the description. I like the idea of rotating the clamps, it would have looked cleaner in the end.

@alan6832 3 месяца назад

@@benwrenchin It's not about looks for me, but aerodynamics, and perhaps ground clearance.

@benwrenchin 3 месяца назад

@@alan6832 I would think this solution probably has a negligible effect aerodynamically. Or, I should say, the problems this solves are of exponentially greater importance than those it creates. To improve emissions, noise reduction, and engine efficiency while creating a slight aerodynamic disadvantage seems worth it to me.

@alan6832 3 месяца назад

@@benwrenchin Rotating the lower clamp 90 degrees, so the bolts don't stick down into the airstream, will not increase emissions, noise, or reduce engine efficiency. Actually removing the clamp entirely will only increase noise, and increase emissions within the car, nowhere else. With computer controlled fuel trim, the loud car should be more efficient, but that may not be worthwhile and not what I argued for. I merely argued for rotating the lower clamp 90 degrees to get the bolts out of the airstream and improve ground clearance.

@benwrenchin 3 месяца назад

@@alan6832 yes, that would be better than what I did, for sure

@faiyadahmed2181 Месяц назад

What is the machine called that u used to cut the exhaust pipe

@benwrenchin Месяц назад

Reciprocating saw. There is one linked in the description

@geraldc.37 3 месяца назад

Nice repair & relatively inexpensive.

@benwrenchin 3 месяца назад

Yes, as long as you already have a reciprocating saw

@marhabihabi8761 Месяц назад

Nama penjepitnya apa bng

@benwrenchin Месяц назад

Exhaust coupler

@StopTeoriomSpiskowym 3 месяца назад

U think it will leak but you not welding it so much rust pipes

@benwrenchin 3 месяца назад

I'm not sure how well someone would be able to weld onto the pipes since they are already pretty rusted anyway

@robintraina217 3 месяца назад

looked like a good job to me?.

@benwrenchin 3 месяца назад

Thank you!

@jacksmith2315 3 месяца назад

Not a bad repair, but if you fix it a third time, then think about how much you spent fixing it 3 times, it would have been cheaper to just take it in and have it welded. Im all for diy, i fix everything myself as well, but theres somethings you have to think logically on. Give it a shot the first time n see how it goes, but if you fix it a second time, then plan on doing it again a third time, just have it welded and be done with it.

@benwrenchin 3 месяца назад

I agree, I originally tested it with the coupler I had on there. Since it lasted quite a while, I tried this and I'll see how long it lasts. So far so good!

@makingmusiconline2309 3 месяца назад

Think how much he’s made from the two videos. Plus every time I take my exhaust in “for welding” they charge me for a new front box and back box too, so $500 rather than $40.

@benwrenchin 3 месяца назад

@@makingmusiconline2309 I don't make any money from videos

@makingmusiconline2309 3 месяца назад

@@benwrenchin that's a great shame. RU-vid still shows me ads to watch your video, so most creators get a share of that. I think content creators should be rewarded for getting people to spend time on RU-vid making the company advertising money.

@benwrenchin 3 месяца назад

@@makingmusiconline2309 I agree, but at the end of the day, RU-vid is allowing me to get exposure for free by providing a platform as well as a number of awesome tools to build an audience with. There is a lot that RU-vid does for us for free that really encourages us to make them more money so that they can start to pay us when we have shown we have what it takes to provide engaging content to an audience.

@nagas13 3 месяца назад

Better take off all exhaust and weld correctly.

@benwrenchin 3 месяца назад

Why's that?

@shaneintegra 3 месяца назад

That would be like $30 to have a muffler shop just weld a new pipe in lol

@benwrenchin 3 месяца назад

If you can find someone to do it for $30, go for it!

@nonyabiz1209 3 месяца назад

You're not wrong. Just had that exact spot re welded on my truck 2 days ago. It took him longer to get the truck on/off the rack than to do the job. Charged me $35.

@benwrenchin 3 месяца назад

Nice, I'll take mine to a muffler guy next time. I always assume the labor cost alone will be more than the cost of parts for me, plus I like doing the work myself.

@jacksmith2315 3 месяца назад

Ya, there's definitely not welder around here doing that for $30. Not unless hes a good friend. Any time ive been to an exhaust shop, even for something simple, at least $100. Maybe just welding up a tiny hole 50-60. But making 2 cuts, a section of pipe, and 2 welds, one on each side, $100 for sure. I would fix it once myself, if it didnt last, doing it a second time, then planning to do it a third time, yes, after the first time id take it to get welded. Its going to cost almost doing it yourself 2-3times, and likely still need to be done again. Having it welded, its done permanently.

@benwrenchin 3 месяца назад

@@jacksmith2315 yeah, for me I think doing it this way is way cheaper and it lasts for long enough that it sure beats paying a lot more to have someone weld a new pipe onto the rust old one.