No video :(

Easy SawStop Throat Plate Insert You Can Make

Подписаться 4,3 тыс.

Просмотров 6 тыс.

50% 1

I was using a dado stack and instead of replacing the zero clearance throat plate with the dado stat throat plate I ran the dado stack through the wrong one. Thinking I could just keep using it with out issue, welp I was wrong. So with the encouragement of Cow Dog Craft Works, I went to the ol RU-vid and found Stumpy Nubs' video on how to make one. So that is what I did and to my surprise it was really not that hard. I made one for my SawStop but this process can be used for any saw, just have to make sure to test fit often.
Cow Dog Craft Works
/ @cowdogcraftworks
Stumpy Nubs
/ stumpynubsworkshop
Amazon Associate links
Making Time, By Bob Clagett
amzn.to/2TWG95m
Relitec Positioning Squares
amzn.to/30NZxG5
Feiyang Miter Springs
amzn.to/2umXm09
Bora WTX 5 Pc Clamp edge saw set
amzn.to/2VYZojb
Bora 24" Parallel Clamps
amzn.to/2JxBKDK
GoPro Hero 5 Black
amzn.to/2IuAliu
MicroJig GRR-RIPPER
amzn.to/2S1xUs4
25 ft Milwaukee Tape Measure
amzn.to/2t7Tn3I
Rigid Cordless Set
amzn.to/2Dn1i4m
Kreg Jig
amzn.to/2JHRp1y
Titebond II
amzn.to/2z0f2OP
amzn.to/2DmGNF2
Knipex Pliers
amzn.to/2Qi3gpj
Saw Blade
amzn.to/2QklLJK
EDC Pouch amzn.to/2yQOhMG
DISCLAIMER: Woodworking and the use of power and hand tools can be extremely dangerous. You are responsible for understanding the safe use of your tools and techniques. Your safety is YOUR responsibility, I accept NO responsibility or liability for any injuries, accidents, death occurring to you or others if you attempt to do the things that I do or use advice that I give.

Опубликовано:

7 апр 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@g.fortin3228 3 года назад

When i made some for my saw I traced the factory one onto the blank... the way you did that part is fine but takes longer. Also lowered the guides on the bandsaw to keep the blade from wanting to flex. Nice end result though...looks great.

@AntonioClaudioMichael 4 года назад

Good tricks with the tape and cutting out the tape in spots you need to transfer

@JkCanvas 4 года назад

Antonio Claudio Michael I tried tapping to get the indent but it didn’t t work so I reverted back to my Navy training and made a template.

@digitalbrick 4 года назад

@@JkCanvas If you have a copy machine, put the throat plate on the copy machine an make a copy. You can trim the paper and tape it to your wood piece

@JkCanvas 4 года назад

Kent Price brilliant idea. Never thought of that. Thank you for sharing.

@AntonioClaudioMichael 4 года назад

@@digitalbrick that is a great idea kent

@BruceAUlrich 4 года назад

Good idea with putting the pieces on top to make sure it is flush!

@JkCanvas 4 года назад

Just following what James did. Really simple design.

@jfsauer42 3 года назад

Would have liked to see a demo showing it in operation. Blade and riving knife going up and down. What was the overall point? Safety? You mentioned dropping the piece of wood in the slot, but did not adequately explain why that scared you. Another benefit is dust control. I'm guessing with a dust collector going, there would be very little sawdust escaping out the top of the saw. I have this saw and the dust collection is mediocre at best. I think this insert would help that a lot.

@JkCanvas 3 года назад

I was cutting a small strip of maple for some edge banding and and just as I finished the cut if fell in the gaping hole left by the dado stack. As it fell it hit the bottoms part of the blade and shot it richer back at me. I was not filming that project so I did not catch the events on film. The overall reason is yes safety because small pieces can become missiles in the shop.