Тёмный

Engine Head Gasket / Cracked Head Repair (Toyota 3.4L V6 5VZ-FE ) - Part 1 

Timmy The Toolman
Подписаться 89 тыс.
Просмотров 31 тыс.
50% 1

Did our video help you? If so, consider buying us a beer: bit.ly/3feE6tJ
This is Part 1 of a 7 part video series documenting the replacement of cylinder heads on the Toyota 3.4 L V6 5VZ-FE Engine. There’s many reasons why you might find yourself needing to remove the heads. You could have a suspected bad head gasket or cracked head. You could have a suspected issue with the head, like a burnt valve, and you need to rebuild the head. It could be because you’re rebuilding the entire engine. Whatever your reason to pull the cylinder heads, this video series will walk you through all the steps necessary to get the job done successfully.
In Part 1, we show you how to tear down the upper part of the engine down to the intake manifold and valve covers.
**Here's a link to the 4Low Magazine article I mentioned in the video intro written by Joel Moranton: 4lowmagazine.c...
*PARTS LIST*
*Spark Plugs #K16TR11 - (Need 6)
amzn.to/2OoIEfD
*Spark Plug Wires #19037-62010
amzn.to/2QyefhD
*Throttle Body Gasket #22271-62040
amzn.to/2KtumsX
*Intake Plenum Gaskets #17176-62040 - (Need 2)
amzn.to/32S0a0Y
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
www.amazon.com...
*1/4" and 3/8" Flex Head Ratchet Set amzn.to/2ql8nNA
*3/8" Drive 6 Point Metric Standard Socket Set amzn.to/32WIh0M
*3/8" Drive 6 Point Metric Deep Socket Set amzn.to/37iQjVt
*1/4” Drive 6 Point Standard Metric Socket Set amzn.to/2QIU7te
*3/8” Drive Regular Extension Set amzn.to/2OehCao
*Milwaukee M12 3/8” Cordless Ratchet amzn.to/2utRZsE
*Milwaukee M12 3/8” Cordless Extended Reach Ratchet amzn.to/3kOsUS6
*Milwaukee M12 Battery amzn.to/3FJZO1j
*Milwaukee M12 High Capacity Battery amzn.to/2HEFTpu
*Milwaukee M12 Battery Charger amzn.to/2uo2o9x
*Flex Head Box End Wrench Set amzn.to/31x8BOo
*90 Degree Needle Nose Piers amzn.to/2VYUro8
*Straight Needle Nose Pliers amzn.to/2pQ6yIa
*Hose Gripper Plier Set amzn.to/3MKe8g2
*Small Pick Tool Set amzn.to/3asf07P
*20 Piece Screwdriver Set amzn.to/34aLrQ1
*CRC Electronic Cleaner amzn.to/3FU5DLa
*Adjustable Spark Plug Wire Puller amzn.to/2MKWrMw
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates, we earn from qualifying purchases.

Опубликовано:

 

10 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 150   
@OlafNolle
@OlafNolle Месяц назад
Dear Timmy and Sean: As a South African now living “Down Under”, thank you for taking much time and putting the effort into making this tutorial video set - to help others rebuild of their beloved Toyota 5vz-fe engine. This was a truly professional job! Without your dedication, I would have failed at saving my Landcruiser Prado. I am so grateful and wish you both all the best as you selflessly inspire others to do the same!
@TimmyTheToolman
@TimmyTheToolman Месяц назад
@OlafNolle It's our pleasure to help out our Toyota Brothers and Sisters around the world. Thanks for taking the time to comment and share such a nice statement about the work Sean and I do. We appreciate it!
@hmu958
@hmu958 7 месяцев назад
I will be rewatching this as I have a head gasket job coming up. Thank you. This is like a shop manual.
@TimmyTheToolman
@TimmyTheToolman 7 месяцев назад
Good luck. I hope it goes smooth for you.
@efil4kizum
@efil4kizum 4 месяца назад
better than a shop manual imo
@brucewayne2773
@brucewayne2773 Год назад
Did both my heads about 18 months ago, wasn't that bad of a job. Ordered all OEM Toyota head gasket kit, and all that you might as well replace parts while you're in there, highly recommended.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the comment Batman. It's not a bad job, but it's fairly involved. Filming more than doubles the time it takes to do it, so maybe my take on it is a bit skewed. It was a ton of work to film and edit this project.
@brucewayne2773
@brucewayne2773 Год назад
@@TimmyTheToolman Filming ,editing and all the small details is definitely time consuming. I applaud you and Sean for doing quality videos. You both helped me greatly with my 4 Runner as always
@TimmyTheToolman
@TimmyTheToolman Год назад
@brucewayne2773 Thanks Batman.
@985VFZE
@985VFZE 6 месяцев назад
What were the size fittings you had for the rings?
@brucewayne2773
@brucewayne2773 6 месяцев назад
Rings were fine, I only replaced the heads@@985VFZE
@solosoundlapaz
@solosoundlapaz Год назад
Thank you Timmy for taking the time to teach us what it is like to do a professional job, not even in a dealership do they offer you a job as excellent as this one. Greetings from México.
@TimmyTheToolman
@TimmyTheToolman Год назад
You're very welcome. We enjoy sharing knowledge with people and getting comments like yours helps us know we're making a difference. Thanks Mexican Toyota Brother!
@marcoharrorato7259
@marcoharrorato7259 Год назад
Amazing video guys very detailed. I actually started working on my own 3rd gen 4runner thanks to this series. I bought it as my first ever car a few years ago to go to university after highschool. It was a huge help in learning how to wrench and fix stuff. After doing this same job 3 years ago you start to learn how everything works and bolts to.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Marco. That's great you got into turning wrenches. Not many people your age are doing it. It's becoming a lost art.
@cbdreamer1709
@cbdreamer1709 Год назад
I’m loving this. Perfect timing for me! I may have a blown head gasket
@TimmyTheToolman
@TimmyTheToolman Год назад
Glad you're loving it, but sorry to hear you might have a blown head gasket. This series will serve you well if you actually have a blown head gasket or cracked head.
@redruuum75
@redruuum75 11 месяцев назад
Friend just bought 02 3.4 taco needing a head gasket. Thankyou! Bolt for bolt, and impeccable timing during your narrative. We both feel as though we took a college course. Best vid and description there is.
@TimmyTheToolman
@TimmyTheToolman 11 месяцев назад
You're very welcome. Sean and I want everyone to be successful using our videos as a tutorial, so we gear them to the absolute beginner at turning wrenches and make them as detailed as we possibly can. Good luck with the job.
@rediranch
@rediranch 9 месяцев назад
For keeping track of where electrical or vacuum lines go, a friend taught me to take telephone or CAT wire and use the colored wires to mark both sides of the connection. Use combination of colors.
@TimmyTheToolman
@TimmyTheToolman 9 месяцев назад
That’s a really cool idea! Thanks for sharing! - Sean
@cbdreamer1709
@cbdreamer1709 2 месяца назад
My favorite series
@TimmyTheToolman
@TimmyTheToolman 2 месяца назад
It’s a solid series for sure. Tons of hours preparing and filming to bring you the very best! - Sean
@jaredt8883
@jaredt8883 Год назад
Nice video! It was almost like taking a quiz, as you were naming parts and hoses, I was trying to call it out to myself first. I think there were only two I missed, the "air chamber stay" I called a "intake plenum stay", so I think I got it close enough. The other was the transmission kick-down cable, I do not have that on my 2000 Tacoma, but that may be because I have a manual transmission. Anyway, as some one who was faced with this same job and chose to rebuild the engine myself, I absolutely agree, finding a good and trusted machine shop is a must! I had the machine shop rebuild and resurface both my cylinder heads, as the "new" one I got to replace the cracked head did not pass their inspection. Just because it looks all clean and pretty does not mean it is flat. They also did the valves, and cleaned, resurfaced, and honed my block. And after all that they surprisingly rebuilt the lower block for free, put together all of the pistons, rods, rings, bearing, crankshaft, everything. Great guys, and worth every penny. Anyway, liked the video, very informative as usual. 👍
@TimmyTheToolman
@TimmyTheToolman Год назад
Wow Jared. Sounds like you have a great machine shop at your disposal. They did you a solid. Thanks for sharing all that with us. Happy Wrenching!
@harryreyes8929
@harryreyes8929 Год назад
Thanks Timmy! Clear and precise honest no fluff pleasure to hear from you!!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Harry. We appreciate your comment. More episodes are coming and you're going to be stoked.
@dcabinet
@dcabinet Год назад
Excellent and very detailed video... This is great.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the compliment. We appreciate it!
@ppeterson9359
@ppeterson9359 Год назад
Great video. Even though I’ve done this part of the job before, I still picked up a few tips. Those hose pliers and right angle needle nose pliers were great additions to my tool box. Good tip re the coolant hoses on the bottom of the throttle body.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks! I just got that hose plier set. I love it. I wish I would have found them sooner. Happy Wrenching!
@scubbarookie
@scubbarookie Год назад
What a great series this is so far. Thank you Tim! Very detailed!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thank you and you're very welcome. I'm glad you appreciate the detail. Happy Wrenching!
@lonzooutdoors
@lonzooutdoors 6 месяцев назад
Literally doing this step by step as I watch. Great content
@TimmyTheToolman
@TimmyTheToolman 6 месяцев назад
Thanks for the compliment and good luck with the job. Let us know how it went when you're all done.
@CaribouHour
@CaribouHour 6 месяцев назад
How’d it go?
@kenny-d3944
@kenny-d3944 Год назад
Thanks Timmy for this great educational video..I have a 1996 3.4 liter Taco..🙂
@TimmyTheToolman
@TimmyTheToolman Год назад
You're very welcome Kenny. I'm glad you found the video educational.
@benaldredge2671
@benaldredge2671 Год назад
Great part 1 with amazing attention to details as always. I’ve been eagerly awaiting this build! You guys take care and looking forward to the next video.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the compliment. I'm glad you appreciate the level of work we put into our videos. We pride ourselves in creating detailed videos for people to use as a tutorial. The next video will be out soon. Stay tuned!
@marvinshorty4611
@marvinshorty4611 Год назад
Am looking forward to the remaining parts of this video series. Thanks for doing this.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Marvin. Part 2 is coming VERY soon. Stay tuned!
@marvinshorty4611
@marvinshorty4611 Год назад
@@TimmyTheToolman I may be using your video series soon. My '98 4Runner just surpassed 440k miles
@TimmyTheToolman
@TimmyTheToolman Год назад
@@marvinshorty4611 Well, let's just hope your engine keeps running with no major issues for a long time to come. But, you are way up there in miles. A definite testament to Toyota quality.
@andrewb2326
@andrewb2326 Год назад
Wow great video. I was hoping it was coming when Sean did the supercharger rebuild. It's a privilege to watch your videos - I learn so much from them.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the nice comment Andrew. We appreciate it!
@SCOC182
@SCOC182 Год назад
I’m excited for part 2!!
@TimmyTheToolman
@TimmyTheToolman Год назад
It's coming soon Bro!
@michaelstern934
@michaelstern934 Год назад
Great part 1 of the series, lots of detail 👍👍 I'd consider swapping heads and rebuilding my rig, if not rebuilt 👀 Thank you and keep up the good work!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the comment Mike. I think I would swap heads as well like Sean chose to do. I've taken very good care of my engine and I would roll the dice the lower end stays intact for a very long time to come.
@davidgoedde8170
@davidgoedde8170 Год назад
Amazing video. Explains everything you need!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Dave. This was just the appetizer. The main course and dessert are coming.
@Gabriel-jc2sc
@Gabriel-jc2sc Год назад
Nothing but the best videos!!Thanks Brother! 💪💪
@TimmyTheToolman
@TimmyTheToolman Год назад
You're very welcome Gabriel and thanks for the compliment. We appreciate it!
@donemmanuel4226
@donemmanuel4226 Год назад
Excellent video as always guys.Patiently waiting for the next video😁.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the compliment. Part 2 will be out in around 4 days. Stay tuned!
@jackwalsh1468
@jackwalsh1468 Год назад
Tim, a very entertaining and informative video. Cheers Mate.
@TimmyTheToolman
@TimmyTheToolman Год назад
We're glad you like it, Jack. Thanks for commenting.
@scraigjohnson
@scraigjohnson Год назад
Awesome video as usual, Timmy....Thanks for the good work!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Craig. We're stoked you like it.
@user-jo4kg8ov3u
@user-jo4kg8ov3u Год назад
Sir,I take my hat off to you. Thanks teacher
@TimmyTheToolman
@TimmyTheToolman Год назад
You're very welcome! Thanks!
@israelrodriguez6986
@israelrodriguez6986 Год назад
Well I wasn’t, first but here I am, and super excited about this one!!!!
@TimmyTheToolman
@TimmyTheToolman Год назад
You can't always be first, but I'd have to say, you're probably one of our most devoted subscribers, if not the most devoted. I can't think of anyone else that was with us at the beginning and still comments like you do.
@jarinespinal184
@jarinespinal184 Год назад
Amazing video guys thank you so much
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Jarin. You're very welcome!
@Glocktard
@Glocktard Год назад
Thanks for the psychological flashback! 😂 I just did my tacomas heads last week. Omg. What a interesting job. With out the use of a video camera probe I wouldn’t have diagnosed it properly. It was a cracked head in cylinder #3 inside the intake valve. I can’t wait to see this whole series. I bought one NEW head from the machinist (I don’t know the brand) but it seams good. I bought all Toyota factory gaskets, bolts, Hoses & Denso radiator with a few new tools. I hope you did the oil cooler O rings since you are there. I think I spent $3300 at least, and I did all the R&R labor. But it’s do-able especially since I’m only half above idiot 😂. The rest of my 2001 Tacoma has 280K and is still serviceable so I spent the money on it. I now have 400 miles on the repair and it runs great.
@TimmyTheToolman
@TimmyTheToolman Год назад
Did you get the idea to use the borescope camera from our head gasket failure diagnosis video? Yeah, you're going to get a serious case a deja vu watching this series. Thanks for the comment. Good job doing the repair. It's a big job!
@Glocktard
@Glocktard Год назад
Ops no, care car nut channel. The best chiniesium $70 camera I have now. 😂😂 After shutting the engine off with even 5 psi applied to Radiator it leaked I little pool of antifreeze on top of the piston. It would then miss once started again. Code = random cylinder misfire.
@michaelrueckert8507
@michaelrueckert8507 Год назад
I've had a JDM engine I bought on eBay since 2015 with no issues. I've put over 100k miles on it and supercharged it in 2018. I've had perfect luck but I get what you're saying. It was definitely still a risk.
@TimmyTheToolman
@TimmyTheToolman Год назад
I'm glad to hear you got a good engine, but others weren't so lucky. I've heard the horror stories.
@michaelrueckert8507
@michaelrueckert8507 Год назад
@@TimmyTheToolman Yes, I'm thankful I was one of the lucky ones. Love your videos! Unbelievable how detailed you guys are! About to do my timing belt and will definitely be following your timing belt video when I do it! 🙂
@TimmyTheToolman
@TimmyTheToolman Год назад
@@michaelrueckert8507 Make sure you watch Part 2 of the Timing Belt Job as well. We share some important information you don't want to miss out on. Good luck with the job.
@michaelrueckert8507
@michaelrueckert8507 Год назад
@@TimmyTheToolman Thank you!!
@corbinail3295
@corbinail3295 Год назад
Freaking awesome video!! Thank you so much guys. Happy wheeling.
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks Corbin. You're very welcome Bro!
@randycorrales1
@randycorrales1 5 месяцев назад
Stressed because I think my 02 Tacoma has a bad head or head gasket. Barely gunna hit 153k miles too so it’s low miles. Any thoughts concerns ???
@TimmyTheToolman
@TimmyTheToolman 5 месяцев назад
What are the symptoms that lead you to believe you have a bad head gasket or cracked head?
@efil4kizum
@efil4kizum 4 месяца назад
@@TimmyTheToolman it must have self-healed itself!?
@ogfaIlen
@ogfaIlen 7 месяцев назад
hey Timmy, wanted your opinion - I’m about to do a valve cover, adjustment + fuel injector job and wanted to know how much more of a pain it would be to replace the head gaskets while I’ve already got the engine apart. I’m at 298k miles and have already completed an insane amount of projects thanks to your videos in order to restore the 4runner as much as possible. I tend to go overboard and replace a lot more than necessary for peace of mind and so that I don’t need to repeat my work soon after. with that said, this will likely be the last major project for a while and I can’t seem to find many forum threads about head gasket failure under normal conditions. all threads of folks doing this job after a leak/failure, but almost none for preventative (imagine that lol) what do you think? is it matter of time before mine starts leaking? or is this job more work than its worth for an engine without issues? Thank you so much for all you do!
@TimmyTheToolman
@TimmyTheToolman 7 месяцев назад
Pulling the heads off is a lot more work, and I would not do it as preventative maintenance. Quite often, the failure isn't the head gasket but the head itself. The head cracks, and the fracture leads to a coolant jacket. I would only remove the heads if I was having an issue like my engine is consuming coolant and I'm getting a misfire.
@efil4kizum
@efil4kizum 4 месяца назад
do you change the yota pink coolant frequently enough? once a year? that should keep it from becoming acidic and eating at the head gasket as far as i understand it currently
@nathandulong4968
@nathandulong4968 Год назад
Doing this job right now! Someone put the head gaskets on the wrong side before I got the engine -_-. Thanks for the video
@TimmyTheToolman
@TimmyTheToolman Год назад
That was a genuis move putting the head gaskets on the wrong side of the block. I don't know if we'll get all the parts out in time for you, though. All 7 parts will be live over the next month.
@nathandulong4968
@nathandulong4968 Год назад
@@TimmyTheToolman All Good! thanks for making these great videos!
@TimmyTheToolman
@TimmyTheToolman Год назад
@@nathandulong4968 No problem. Part 2 will be out in a few days.
@on-site4094
@on-site4094 Год назад
👍
@hmu958
@hmu958 7 месяцев назад
JDM motors are low mileage but high idle hours. There's a reason there are no old cars on the road in Japan. The older the car the more expensive the taxes in Japan.
@TimmyTheToolman
@TimmyTheToolman 7 месяцев назад
Very true.
@efil4kizum
@efil4kizum 4 месяца назад
I heard recently from a guy originally from the Philippines that moved to Chicago from California that things are much different in Japan in regards to maintenance and why there are few older vehicles on the roads. They have comprehensive lists of must-do maintenance (whether it needs it or not) to comply with the law. these required maintenance costs greatly increase as the vehicle ages. So they send their older vehicles to a secondary market such as the middle east and areas such as that.
@cbdreamer1709
@cbdreamer1709 Год назад
Totally rad!
@TimmyTheToolman
@TimmyTheToolman Год назад
Yeah, we think so too. Thanks!
@sommaykongmalay8492
@sommaykongmalay8492 Год назад
Hi Timmy, I wouldn't have been able to remove the head so easily without this video. I own a 1997 Toyota 4Runner 4x4 with a 3.4L 5VZ-Fe engine, and it has already covered 290,000 miles. Now that the heads are off, I'm considering replacing the piston rings and bearings. I just wanted to know if it's possible to do this without removing the engine
@TimmyTheToolman
@TimmyTheToolman Год назад
It's possible, but the front differential would need to come out so you could drop the oil pan. I think it would be easier to remove the engine and more comfortable for you to do the work with the block on an engine stand. Be sure to do plenty of research because there's a lot that can go wrong with this kind of work. You have to properly match up the rod bearings, hone the cylinders, and get the right piston rings. It can be done, but you have to be meticulous to make sure you do it right.
@sommaykongmalay8492
@sommaykongmalay8492 Год назад
@@TimmyTheToolman I think I will remove the engine like you suggested. Again, I appreciate your video, please keep it coming.
@TimmyTheToolman
@TimmyTheToolman Год назад
@@sommaykongmalay8492 We will continue making videos for a long time.
@efil4kizum
@efil4kizum 4 месяца назад
@@TimmyTheToolman are you redoing some of your very OLD videos from last decade that did not have the bestest of audio/video quality?
@efil4kizum
@efil4kizum 4 месяца назад
@@sommaykongmalay8492 i have a '97 Taco with same engine and a manual transmission that has now covered 350,000 miles. why are you having to consider piston rings, bearings, and why are the heads off at this mileage + age?
@kedronpful
@kedronpful 9 месяцев назад
Can I do this job without a Milwaukee rachet?
@TimmyTheToolman
@TimmyTheToolman 9 месяцев назад
I see somebody went to the Smartass Institute of Technology. Use a crescent wrench for the whole thing if you want. Electric ratchets save time and energy and that's why we like them.
@mtsanchez27
@mtsanchez27 5 месяцев назад
Hi there, do you know how many hours this jobs takes to get it done by the book?
@TimmyTheToolman
@TimmyTheToolman 5 месяцев назад
No, I don't have information on book time for jobs. I'm a DIYer, not a shop, and I don't have access to that information.
@mtsanchez27
@mtsanchez27 5 месяцев назад
@@TimmyTheToolman estimate? Thanks in advance!!! Great info like always
@TimmyTheToolman
@TimmyTheToolman 5 месяцев назад
@@mtsanchez27 I don't have an estimate.
@efil4kizum
@efil4kizum 4 месяца назад
there ought to be someway somehow to get a rough estimate? not many seem to do by the book now however, its just slop and hack and more slop from trained proshops, it gives me ulcers 8^{
@efil4kizum
@efil4kizum 4 месяца назад
@@mtsanchez27 i would gander it to be no-less-than 2000$
@StandFast1611
@StandFast1611 4 месяца назад
Is it worth fixing if I have a p0300 code, had it inspected and said it has "hydrocarbons" due to coolant.
@TimmyTheToolman
@TimmyTheToolman 4 месяца назад
P0300 is a general misfire code. Your engine is consuming coolant due to the hydrocarbons detected in the coolant. It's either a bad head gasket or cracked head. It depends on the mileage whether or not it's worth replacing the heads or just completely rebuilding the engine.
@StandFast1611
@StandFast1611 4 месяца назад
@@TimmyTheToolman it has 240k miles on her, so I'm at a fork in the road on what to do
@TimmyTheToolman
@TimmyTheToolman 4 месяца назад
@@StandFast1611 That's sort of a crapshoot. If you are going to do all the work yourself and you can get a good deal on a quality set of heads, I think it's worth just doing the heads rather than a complete engine rebuild.
@StandFast1611
@StandFast1611 4 месяца назад
@TimmyTheToolman Should I just drive it until it blows? I mean it runs fine but warming it up is rough! It Shoots white smoke like crazy but after the temp gauge gets to normal temp, it rides like new
@TimmyTheToolman
@TimmyTheToolman 4 месяца назад
@@StandFast1611 It runs rough because your engine is burning off coolant in the cylinder(s). I guess as long as you keep an eye on the coolant level, you can keep driving it like that.
@pwfcpwfc
@pwfcpwfc Год назад
Hi Sir , Thanks you for making those great educational videos . By the way where can i find the link of the article you mentioned on your video ( what to look for good reman. engine ) ? Thanks
@TimmyTheToolman
@TimmyTheToolman Год назад
We got an advanced reading of the article. It's not yet published, but it will be soon. We'll provide a link to it in the video description when it is published.
@pwfcpwfc
@pwfcpwfc Год назад
@@TimmyTheToolman OK Thanks.
@TimmyTheToolman
@TimmyTheToolman Год назад
@pwfcpwfc We were wondering if we should mention the article since it wasn't published yet, but since it speaks very well to the topic on hand, we decided to take the risk that it does end up being published. I'll try to remember to comment back when it is published so you can check it out.
@jorgebarboza8051
@jorgebarboza8051 Год назад
U da man timmy
@jorgebarboza8051
@jorgebarboza8051 Год назад
I can tell you are a fireman. Funny story, I got hired by the fire department where I was an explorer when I was 21. I quit because I was lame (probably scared). I spent 5 years working towards that goal. Now I am a nurse practitioner at a great job and I still think about being a firefighter from time to time 😂
@TimmyTheToolman
@TimmyTheToolman Год назад
What gives it away I'm a firefighter? Is it my charisma and good looks. LOL Being a nurse practitioner is a great career. Firefighting is a pretty cool career but every career has it's pluses and minuses.
@jorgebarboza8051
@jorgebarboza8051 Год назад
@@TimmyTheToolman haha. Just been around enough firehouses to know. Looking forward to the rest of the head gasket series. Will seriously debate new heads vs yota 1 engine when the time comes
@TimmyTheToolman
@TimmyTheToolman Год назад
@@jorgebarboza8051 Gotcha. You'll enjoy the series. More really good stuff coming.
@mattwernecke2342
@mattwernecke2342 Год назад
I've about given up trying to find a 4runner.
@TimmyTheToolman
@TimmyTheToolman Год назад
Is it because people are asking stupid money for them?
@mattwernecke2342
@mattwernecke2342 Год назад
@@TimmyTheToolman That's part of it. I've been watching one for 3 months; he just raised the price.??? I can find 2 wheel drive, but I want a 4wd that is stock. Hard proposition in Atlanta area.
@TimmyTheToolman
@TimmyTheToolman Год назад
@mattwernecke2342 I'll most likely be visiting my buddy Jordan in November in Atlanta. We had a get-together last year there.
@mattwernecke2342
@mattwernecke2342 Год назад
@@TimmyTheToolman Awesome! That's a great time of year to go!
@TimmyTheToolman
@TimmyTheToolman Год назад
@@mattwernecke2342 If we're going to do another get-together at Jordan's place, I'll announce it on our channel by doing a video invite. If you're subscribed to our channel and receive notifications, you'll see the video.
@joshgill5329
@joshgill5329 Год назад
How long will your engine run with a blown head gasket?
@TimmyTheToolman
@TimmyTheToolman Год назад
It could last a long time. You just have to keep an eye on the coolant level and not burn up your engine. But, you may be dealing with a misfire as well and thus have poor engine performance.
@joshgill5329
@joshgill5329 Год назад
Mine runs great. Only symptom I have is the white smoke and sweet smell. No codes no coolant leak or extra usage. Will do a block test soon
@TimmyTheToolman
@TimmyTheToolman Год назад
@@joshgill5329 The white smoke and sweet smell is indicative of your engine burning coolant. Maybe the leak into the cylinder is very minor.
@joshgill5329
@joshgill5329 Год назад
But it still means it’s the head gasket?
@TimmyTheToolman
@TimmyTheToolman Год назад
@@joshgill5329 Or a crack in the head.
@MrBeefsnorkel
@MrBeefsnorkel Год назад
Fellow long time toyota tech here - I DO NOT RECOMMEND getting any cylinder head on a toyota resurfaced, or any other brand that is manufactured well (tight tolerances). The material taken off of the head actually causes engine timing issues, poor performance and check engine lights with cam timing codes. It actually makes the length of the timing chain different enough to throw off the timing. If you own a toyota, get a NEW cylinder head, do not get it machined!!!!!!!!!
@TimmyTheToolman
@TimmyTheToolman Год назад
Thanks for the input. I think a lot of expert engine builders and machinists are going to disagree with you. From what I understand, you can safely take off material to machine the surface. You just can't take off an excessive amount, because then, you can run into the issues you mentioned. I'm sure you're knowledgeable and your comment is backed up by real world experience. I just think the results you mentioned are from people taking off too much material. There's countless people out in the world running engines with machined heads without issues. So, while I agree that what you said can happen when too much material is removed, I disagree with your advice that nobody should get cylinder heads resurfaced.
@MrBeefsnorkel
@MrBeefsnorkel Год назад
@@TimmyTheToolman Perhaps my statement was far too final. I think what my mind was thinking of, at the time, was the more modern engines (2014+) that I've personally worked on or seen at the shop for 8 years. Anecdotal evidence is not exactly the best.....so I'll give you that. I've seen it multiple times, but that doesn't mean it happens all that much. I appreciate your respectful discourse. I see why people like you
@TimmyTheToolman
@TimmyTheToolman Год назад
@MrBeefsnorkel Well, I'm far from an angel. When people push my buttons or are outright disrespectful, they get a much different Timmy. I can be an a-hole. Your comment didn't qualify for me to summon Bad Timmy. You made a statement, and I gave a response. There was no need for me to be a jerk, but I needed to respond to your statement and share my thoughts about what you said. I also appreciate the civil exchange we could have. So, thanks, and Happy Wrenching!
@edwarddeguzman489
@edwarddeguzman489 Год назад
Hi Tim, how can I DM ,PM you if I have questions?
@TimmyTheToolman
@TimmyTheToolman Год назад
Are you on Facebook? If so, I have a Timmy the Toolman page you can message me on.
@levigarrett5614
@levigarrett5614 Год назад
Yeah I was just about to get a yota1 3rz. All the jdms and used engines say they have 60k on them😂
@TimmyTheToolman
@TimmyTheToolman Год назад
Yeah, isn't it curious they all have 60k on them. Getting an engine from Yota1 Performance is a great choice. You won't be disappointed.
@levigarrett5614
@levigarrett5614 Год назад
@@TimmyTheToolman awesome thanks for all the videos.
@TimmyTheToolman
@TimmyTheToolman Год назад
@@levigarrett5614 Our pleasure.
@chriscollison3136
@chriscollison3136 Год назад
In Japan by law they have to change out the engine or buy a new car at 75000 miles so that’s why they look like crap cause they don’t care about it cause it will be gone soon.
@TimmyTheToolman
@TimmyTheToolman Год назад
I have heard that before and makes sense.
Далее
Toyota engine 5VZ-FE cylinder head removal
18:58
Просмотров 21 тыс.