Ep 2 - Gibson Chet Atkins Repair - How to level & crown the frets

Подписаться 321 тыс.

Просмотров 104 тыс.

50% 1

Welcome to Crimson Guitars ru-vid.com...
We often get really interesting guitars in for repairs at www.crimsonguitars.com and this one just had to be filmed.
It is a beautiful old Gibson Tennessean Orange Chet Atkins Signature. These were made between 1958 and 1980 and it is really a rather lovely guitar. The problem is one of really poor maintenance/repair/setup over the years and it is in the workshop to be made playable.
This is the 2nd of 3 episodes following the whole process in depth. In the last tutorial, Ben filled the gaping nut slot holes using the dust and glue method.
In this episode, Ben goes through each process involved in leveling, crowning, and polishing the well-worn frets of this lovely old guitar. You can do this at home with only a few specialist luthiers tools that are available from www.crimsonguitars.com/shop our own luthiers' supply store in the UK.
Chapters
0:00 Introduction
0:10 Making sure the neck is straight using a notched straight edge
1:37 Masking off the fretboard and nut
8:06 Use a permanent marker on the frets -
8:42 Levelling file next
10:56 Applying more marking ink then use a 3 corner crowning file
13:07 Another option - fret end dressing file can be used
14:23 Rounding the frets over - the options.
240 grit, 600 grit, fret rubber, and Autosol
20:41 Off with the masking tape
Conclusion
______________________________________________________________________
We'd like to thank our partners for helping to make this video series possible.
Triton Tools - www.tritontools.com/en-GB
Wagner Meters - www.wagnermeters.com/
ISOtunes Bluetooth Hearing Protection - bit.ly/36YmKro
Support us by supporting our Partners, and at the same time get yourself a great deal with ISOtunes.
Use code "CRIMSON10" for £10 off at "isotunes.co.uk" or $10 off at "isotunes.com"
Get the Freshest CA glues in the market (USA orders) at www.starbond.com
Use Code 'CRIMSONGUITAR' at checkout to save 15% off on your purchase www.starbond.com/?rfsn=495373... ______________________________________________________________________
WEBSITE: www.crimsonguitars.com
Luthier’s Tools & Supplies: bit.ly/LuthTools
Guitar Building Courses: bit.ly/LuthierySchool
Kit Guitars: bit.ly/KitGuitars
SOCIAL
Instagram - / crimsonguitars
Facebook - / crimson CustomGuitars/
As always, thank you so much to our Patrons, who help make videos like this possible.
Patreon - / crimsonguitars
OTHER
Ben's Vintage Tool Shop - vintagetoolshop.com/
Thank you again for all your support, we really appreciate it! - Ben
Stay tuned and stay awesome!

Хобби

Опубликовано:

27 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 98

@MultiSpeedr 5 лет назад

Dude your method of finishing the crowned frets, saved me a ton of time, and gave me an amazing job... Ben Thank you....

@JackstandJohnny 6 лет назад

Dude, I love your channel so much. Once I have the money I am absolutely buying tools from your website. Between you and Wills Easy Guitar my understanding, knowledge and confidence working on guitars has really blossomed. Thank you. I am so grateful.

@madmick9205 2 года назад

I can tell people that the notched straight edge is a very high quality piece of engineering. It's solid! Mind you, all their tools are awesome. Proper works of art, made with a lot of thought:) Great video, thank you.

@PelleKuipers 9 лет назад

Thanks so much for this video. I used this one and a similar one to learn how to leven & crown frets. Used your file + fret rocker and it worked like a charm. The next step will be also fretting my own guitar :-)

@kaskas55 Год назад

This is a masterclass. Thank you so much!

@MikkjalHvannastein 6 лет назад

Heading to your store as i type. Awesome videos. Thank you so much for sharing this craftmanship. I am located in Faroe Islands, and here it´s only 1 luthier, and he lives on another island, and has no time to do this for me. Thanks again :)

@jettramel 6 лет назад

This is how you do it, great video, I learned mine from Dan Earlewine, I use painters tape because its easier to get off, & I love the triangle file, I have the McDonald fret files & they do mess you up at the ends. Excellent work.

@paulyoung4781 Год назад

Wow metal polish just makes it absolutely amazing I need that stuff

@docoluv9 9 лет назад

Ty ben for a quick answer. Ty again for all the vids and info buddy.

@russseuffert803 5 лет назад

An excellent instructional video! Thank you.

@solonaskypros3263 3 года назад

I'm very happy with the result thank you so much

@paulyoung4781 Год назад

Ur such a great teacher,u no ur stuff obviously ur a luthier!

@12south31 4 года назад

One of Chets old pickup covers is in a little display case at Sam Ash in Matfield Hts Ohio.

@CrimsonCustomGuitars 4 года назад

That is actually pretty bloody awesome! B

@12south31 4 года назад

@@CrimsonCustomGuitars They also have old Gibson guitar strings still in the original packaging and a few original Big Muffs still with the boxes and paperwork autographed by their inventor. Cool stuff!

@markfisher2282 2 года назад

Detritus Ben? Nice to hear proper English. Not the average fetid spew. One of the reasons why your show is tops. You rock.

@llengford 3 года назад

It looks like the end of the fretboard is not getting as much finishing as the beginning

@mikeraidos 5 лет назад

I Love All Your Working Videos..!,!! On Your'' GUNS' '..! 👌👌🎸🎸🎸

@rexhelley1828 7 лет назад

I polish with 2000, 3000, and 5000 grit sandpaper then autosol - it's almost blinding how shiny they are

@pigdick2233 2 года назад

I’ve found using a short fret leveling file the frets in the middle spend more time under the file and the last frets and the ones closer to the nut spend less and less time being filed so the frets end up not being truly level

@TheScaredofsilence 8 лет назад

Anyone use sanding sponges to remove scratches after crowning? Great vids by the way

@jacoponaspi9577 10 лет назад

wow..that shows really "in depth" how you do your fret leveling! i do love this vid! ...i just would have liked to see you oil the fretboard, but that's fine! :)

@mikeraidos 5 лет назад

Yea. Me2! 👍👌🎸🎸🎸

@ThaUltimateDragon 10 лет назад

Autosol is great, but I'd recommend 'Belgom Alu' for even more smoothness. I've been polishing metal for the past four years, and Belgom is one of the best things to finish polishing with.

@jaeztheone 4 года назад

also...Semichrome Polish....all US guys it - for scratch remover on body finish too

@esa062 10 лет назад

I like using stronger masking tape (the blue stuff) because then 1 layer is enough. Saves some time. BTW, did you forget to turn the neck rest around for leveling, or don't you just find it necessary?

@aria8928 7 лет назад

i'll have you know I use y ring finger nail to score the tape.

@satanshollowd 10 лет назад

I am so going to but one of those straight edges having the right tool for the job makes it so much less painful Where is the best place to ask a possible vlogcast question?

@thechimpyone 10 лет назад

Is it just me or is that a Tardis taking off at 10:00?

@eddievhfan1984 5 лет назад

Throw enough echo and reverb on it, and it would be.

@DannyGatton94 8 лет назад

How often should I polish my frets? I'm in afraid of doing so.

@paulyoung4781 Год назад

Only thing I'm abit worried abit is when rounding the frets off crowning them but if I take time I'm sure I'll manage ye!!

@mallrat11 7 лет назад

how long do you spend with each grit of sandpaper?

@memesupreme4338 5 лет назад

around 10 minutes, while leveling. Does the same method apply for compound radii?

@in2deepband 3 года назад

Thanks Ben but when do I know when my frets are passed a dress and need renewed? I have flat frets from frets 10 upwards to the point I am dragging/catching

@idealmethod 9 лет назад

been watching your videos for a while now, can you make one with you selling the crimson custom tools start up package for fret leveling tools. I need one! With there was a company that sold and talked you through it. ( the supplied tools)

@TheHammetman 10 лет назад

Great video man! btw can you explain why steel wool are nasty for polishing frets? Thanks

@nectarandice 2 года назад

If you have pickups the steel wool will shed as you rub it along the frets while polishing. The steel hairs that fall away from the wooly pad are attracted to the magnets in your pickup and enough of this material built up around the apparatus will damage the pickup and even short the wires. You really have to tape off the pickguard well if you choose to use steel wool.

@nizodizo9549 5 лет назад

Detritus? How many points in Scrabble do I get?

@mantovannni 10 лет назад

I'm currently fixing up an old spanish guitar at the moment and the new nut i have is a different size. could you tell me how much height I need to have between the nut and the fretboard? I don't want to get it wrong and ruin the action or something.

@JDODify 2 месяца назад

This is an old video now, probably from about when I bought my Crimson Custom! Is this still how you'd advise we do fret levelling - I've got a Telecaster that needs a lot of work.

@tonyn9858 7 лет назад

good video thank you,,

@andy_182 3 года назад

what is the sandpaper version of the fret rubbers

@nevermore7421 6 лет назад

do you have special Crimson Guitars masking tape and magic markers? oooh, and custom detritus brushes, too?!?

@shaunm1983 7 лет назад

I have to fret notes way harder than usual to avoid buzzing on my newest acoustic guitar, is this because the frets are too low or because maybe the neck is too straight ? I would really appreciate if anyone could help.

@mr.poopybutthole4562 Год назад

What grit do you use on the levelling pane?

@xav3ng3rx Год назад

is there a reason you like using the leveling file over something like a flat beam that's longer?

@themixmusicandmore6280 11 месяцев назад

How do i level a compound radius board?

@SeanDS89 Год назад

12:46 Detritus - waste or debris of any kind (according to the Oxford dictionary) lol thanks, now I can sound smart when someone spills something "what's the meaning of all this detritus??" 😂

@tutorialinater 10 лет назад

Question: should I carve the neck before or after putting the frets in? Thanks

@CrimsonCustomGuitars 10 лет назад

***** tutorialinater I prefer to fret before carving, it gives a more stable surface to work from. The downside is the fret pressure wants to bend the neck back and if you have a pre-carved neck you can see it happening if your fret slots are too narrow, with an uncarved neck it will only move after the carving.. I always use dual action truss rods just in case and rough cut the necks pretty close to their final dimensions before fretting.

@me5ponk454 9 лет назад

Whats your opinion of the Katana fret leveling system and other similar products?

@CrimsonCustomGuitars 9 лет назад

Get leveller needs to be perfectly flat, period. Sounds like a great idea until you realise you end up with some frets barely touched and others half sanded away. I must say though that I am biased, of course, and have not actually used one.

@Treadplate367 3 года назад

What is a “Gary Block”?

@EonTide1111 2 года назад

Have you ever used a z file?

@skyscraperGB 10 лет назад

I have a question, if I may. Regarding levelling the frets- surely the levelling file needs to touch all the frets by the same amount? From 8.39 to 10.14 the file is running the length of the fingerboard but the lowest and highest frets are only being touched by the last inch or so of the file, whereas the other frets are being touched by the whole length of the file. Surely removing the neck position pickup and the nut and then running the whole length of the file along the fingerboard and over the nut slot and headstock (without touching the latter obviously) would mean that all the frets would be touched by the whole length of the file?

@InstrumentalReason 9 лет назад

I have been wondering about this for a while as well. Opinions?

@skyscraperGB 9 лет назад

Yes, an answer would be nice. Its been over a month since I asked the question.

@richardvillafana2894 9 лет назад

Question when your running that file along the entire neck to level the frets how does that make all the frets level let's say some are still high do you only focus on the high ones or continue passing every fret it seems to me? That I'll just keep lowering the low ones also?

@BlackHawk2029 8 лет назад

the file rides the high frets, so it doesn't even touch the low ones until it grinds the high ones level. That's why it's important that the file is perfectly flat.

@Snowy0123 6 лет назад

richard villafana if you have high frets the perfectly level file won't touch the low frets until it lowers the high frets. Once you see the ink only in spots your seeing the low spots,

@andrewgalloway7344 5 лет назад

can i ask ... when you have just one black fret left ... how do you know that that fret isn't TOO low.. where sanding down to it's level would make all the frets too low?

@manifestgtr 5 лет назад

Couple of things there. I always run my finger up and down the frets to see how “bumpy” they feel in relation to the board. It doesn’t take a crazy skilled hand to know how much fret you have left to work with. Most of the time you’re good...and you’ll know when the frets are too low, trust me. Secondly, leveling down to the lowest fret is seldom as far as you think it is. You’re not really taking off much material unless you’re really going at it. Lastly (this may be a bit controversial)...I’ve done hundreds of levels over the years and most of the time, when there’s a fret that’s lower than the rest, it’s way high up on the neck. For example, you’ll be working on a fender with a lot of “skateboard ramp” or an acoustic fingerboard that falls away and the very last fret is a bit of a holdout. I tend not to worry about that so much. There’s basically nothing for it to buzz into anyway. So if it comes down to telling a client it’s time for a $300 refret or letting a guitar go with the last fret a little low, I’ll often just let it ride. I haven’t ever had that one come back to bite me so I think it’s pretty safe to say at this point.

@Rivin5191 9 лет назад

Hey Ben. Love your Vids!! Why dont you just use the thinner masking tape for the higher up frets instead of using the thicker and cutting along the fret?

@LandonsGrampa 5 лет назад

TJ Stilijer, because then the excess that he is making use of, would become nothing more than trash. Why not use that waste, before it actually becomes trash? Sure, it doesn't account for much more than a fraction of a penny with 1 job, but incorporate that into a 30-50 year career. And we are only talking about tape. Change your mindset to more expensive things like epoxy, sandpaper, pigments, oils and so much more. How much do you think all of these "penny saving" tips would save you, over the course of many years? You obviously have no clue how business expenses work.

@SeanDS89 Год назад

Question: do you leave the thin strip of ink for the polishing stage, or should you take if off as the last bit of crowning with the file? I hope that makes sense lol

@CrimsonCustomGuitars Год назад

Leave it for the polishing stage, it is the bit you don't want to touch until the very end of the process now

@SeanDS89 Год назад

@@CrimsonCustomGuitars ok cool, thanks :)

@seanodonnell3683 10 лет назад

I love your work, but get cracking with part three!! This video cut off WAY too early!

@docoluv9 9 лет назад

Hey ben do you ship to the states here... I live in louisiana near new orleans...

@CrimsonCustomGuitars 9 лет назад

docoluv9 we absolutely do, drop us an email or check out www.crimsonguitars.com/shop and it will work out shipping costs etc if you need tools, for a custom guitar we do that in person :)

@nevinmarknarciso 2 года назад

which one to clean 1st, the frets or the fingerboard?

@CrimsonCustomGuitars 2 года назад

I generally clean the fretboard first but don't oil it again before you do the frets.. if you do then the masking tape won't stick down!

@nevinmarknarciso 2 года назад

@@CrimsonCustomGuitars do u have video on how to clean unfinished maple fingerboard?

@getredytagetredy 8 лет назад

I had crowned frets on my Gretsch super chet that looked like a crown on top , not flush...

@simpleone1989 8 лет назад

Ben why is wire wool nasty?

@simpleone1989 8 лет назад

That's true even though I mask my pickups before using it.

@ernieslespaul2710 Год назад

any reason you didnt hit it with a radius block at the end?

@CrimsonCustomGuitars Год назад

Radius. Locks are for setting the radius on the fretboard before putting frets in, I would hardly ever consider using one when doing fret leveling, and then never one made of wood that may warp slightly. They simply are not as precise and levelling beams etc in most cases

@ernieslespaul2710 Год назад

@@CrimsonCustomGuitars Thank you for the advice!

@ashscott6068 6 лет назад

I'm confused. I keep hearing that you should level frets parallel to the center of the neck, not along the path of the strings. I also keep hearing that you should follow the line of the strings. AND I keep hearing that you should follow the center normally, but the strings if the fretboard has a compound radius. I guess it can't make a big difference, or there would be no confusion...

@lone-wolf-1 3 года назад

I‘m late, but that gave me to think. I imagine the radius of the frets as a cylinder- if you grind parallel to the center line, you are evenly on the surface. But if you grind at that angle following the strings, you basically have to grind a slight dent in the middle part… Compound radiuses do compensate for that. I would always follow the strings. The difference is probably very minor…

@Stratocaster893 10 лет назад

Great vid. Would have been nice to get a look at the finished product though. You cut out too early.

@CrimsonCustomGuitars 10 лет назад

You can see the final result in the 3rd video.. It was made live last week. How you enjoy it :)

@Stratocaster893 10 лет назад

Crimson Custom Guitars Ah, there we go. Thank you very much.

@connshawnery6489 3 года назад

I literally invented this exact taping technique years ago. Proves that no one is truly unique and maybe there’s some metaphysics to thoughts after all.

@mindfuc 5 месяцев назад

12:04 Bwaahahah....Rather well, how arrogant! You da man!

@Neechan0077 10 лет назад

The reason why your fret dust isnt magnetic is because you use the hypoallergenic stuff. Thats full brass. Brass isnt magnetic. However, other companies use a mixture of brass and nickel and nickel IS magnetic and will murder your pickups. So for your own build guitars, theres no need to tape off the pickups because of your consideration to the people of the world with allergies.

@peppe406 5 лет назад

Gotta cover up them goofy tribal tats.

@MrAnderswt 9 лет назад

Why did you tattoo your head?

@jman1428 2 года назад

I owned one of these guitars, what a pile of junk, and bassy pickups.

@CrimsonCustomGuitars 2 года назад

I'm not surprised.. it took a lot of work to make it playable.

@dannicoelet9915 2 года назад

Your three corner file is made in Vietnam 🇻🇳, not in the uk ( I bought one ) and I was pissed of, when I saw it, because I don’t wanna pay for child’s labor, and you should be ashamed of yourself……..