ETCG's Air Tools and Compressor

Подписаться 1,8 млн

Просмотров 596 тыс.

50% 1

Visit me at: www.ericthecarguy.com/
I get asked about my air tools and compressor ALL the time so even though I've made a video about my tool boxes I thought I would make a video JUST about my air tools and compressor. One of the most popular of those questions is, "What kind of compressor should I get?", as far as kind that's up to you and what you can afford but I think this 26 gallon is perfect for the DIY. As for the air tools well I used mine every day so I bought the best I could get at the time but consider how you're going to use the tools, if it's just on weekends for your own projects I don't think you need to spend as much to get results that will work for you. I also cover a bit of compressor maintenance as well as air tool maintenance which you might also find useful.
Enjoy the video
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Авто/Мото

Опубликовано:

4 окт 2012

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 351

@josephmiddeton5004 3 года назад

Put a 5 gallon plastic tray under the compressor when purging to help the stains and slips 🤙

@jeanpaulvargas3645 11 месяцев назад

I used ru-vid.comUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell

@Bobherry 7 лет назад

I got my first air compressor today, It was from Harbor Freight and is working great!

@blackbear92201 9 лет назад

Great video. Very helpful to hear from a professional like Eric.

@powergrower 11 лет назад

dude sum of your vids have saved my so much time trouble and money just want to say thanks and keep up the good work

@gjmarsh8787 5 лет назад

Thanks Eric, great explanation - it helps us DYIers.

@Ipoditouchreview3r 11 лет назад

i have a craftsman cordless 1/2'' impact gun and i love it! Not that much torque but it can always take off tires if torqued to the correct speck.

@YoungChristopher1 9 лет назад

100% agree on that max 3/8. Got one from someone who quit at a cheap price and it's my go to air gun.

@adilkhan7020 7 лет назад

Great information for people new to air tools !

@2koolforyou88 11 лет назад

Thanks for the behind the scenes of what tools you use

@nvrdwn3140 4 года назад

My dad bought me a 60gal ingersoll rand and it is by far my favorite thing he has got me. I just recently moved and I'm looking to hard pipe it in with 1 inch copper.

@macmaniacal 8 лет назад

wut. Never oil air tools? that's a first time I've heard that. "apply 4 or 5 drops of pneumatic oil into the air inlet and run it for several seconds. Maintain this tool regularly by performing the same oiling application every 3 to 4 hours of operation"

@davegto67 11 лет назад

Very informative as always, Eric! Thanks!

@TheMrmpsmh 8 лет назад

I got the Hazet 9012M impactgun and its amazing! its a 1/2" and its tiny only 4.4" long and 1.3kg light. It is rated at 811 ftlb for loosen and 500 ftlb for tighten. I work on busses, so basically trucks and it does the job if dont ask too much from this little machine, like loosening truck wheelnuts

@eurokid83 9 лет назад

I've got that exact same MAC/IR composite 3/8" drive impact gun. It's a good tool.

@AutoTechMadsen 9 лет назад

I also have the ratchets and 3/8 impact, its been about 10 years and they are indeed some of the best.

@ACoustaDC 11 лет назад

Hey Eric, this was a great video, I enjoyed your insight and opinion.

@CLaM734 11 лет назад

Hey Eric! If you're still considering fixing that broken 1/4" ratchet, I know for a fact mac still makes it. I have the identical sealed head ratchet that I dropped and broke few months ago. I gave mac a ring to get the necessary repair parts and it was at my door step soon after.

@jeremycole6873 5 лет назад

I have a 60gal and have always wanted more power come to find out bigger hose makes 100% difference never knew it would make that big of a difference

@dwightcarter6334 8 лет назад

Change out the drain valve on the bottom of the air compressor tank with a brass 90 and then an in line ball valve. It makes it way easier to get to, easier to open and close, and you can direct it into a bucket and keep the mess off the floor. Love the channel!

@FA-sr6lx 7 лет назад

good idea

@danny10spot 11 лет назад

You are the man thank you so much for all the knowledge you share

@czarpeppers6250 8 лет назад

If you ever do any interior detailing for your cars, you should look at getting a Tornador. I use to detail at a GM dealership and they had those, and they are absolutely incredible for detailing interiors. It is pretty easy to get a show room level look with pretty minimal effort. Cleaning the carpets, dash, getting in all the air vents, absolutely must have for anyone who has an air compressor. I use to have an old Volvo 240, and my interior always looked pristine because I had access to the thing. Since I stopped working there I have wanted my own air compressor just for one of those Godly tools.

@JonBecker81 3 года назад

Woah! I just started watching your channel and then this one popped up. You’re like a completely different person now. Different voice and all.

@brownranchcustoms1651 7 лет назад

one of the guys at the shop where I work has a Snap-on air hammer that dang near makes the floor shake

@h2bbuilt 8 лет назад

Eric you should make a compilation video of how all these tools helped you out on the toughest jobs.

@BoredNotanymore 11 лет назад

1. Change compressor oil regularly. 2. Dehumidifier in the air line is usually a good thing (can cause pressure drops). 3. Air tools should be oiled regularly (oiler in the air hose does it automatically).

@ktmracer2365 9 лет назад

I have a whole drawer just full of die grinders. Im surprised you arent running air swivel fittings so useful especially on air ratchets. I personally like air tools over electric, I found my two electric impacts come air in handy sometimes when i working with someone else on a project and they are using the air but they arent very durable like my air impacts. im always worried about getting oil and grease inside the electric motors plus they burn out after a few years and get hot which cause it not to work as good, not to mention they are a lot more heavier in weight and harder to fit in tight places. but anyways nice to see the video. I like to see what automotive is like compered to heavy duty industry

@Pr0v1nc3 11 лет назад

Good thinking on that air drill pressure adjuster.

@mikegiammarino3126 7 лет назад

Great video, thank you, Mac oil is not easy for me to find, what else could I use?

@pcofranc 10 лет назад

Nice enjoyable tour of you air tools. Kira is right that IR if feed with 150+ psi should blow the Honda crank bolt off in a split second. My 20 year old 450 ft/lb harbor freight impact gun did when I removed the quick disconnect fitting and screwed in a 1/2 ID 10' hose directly in to the gun and turned my compressor up to 165 psi. The bolt came off and went flying out of the socket. It was so fast it was like a gun shot.

@TechSeller 7 лет назад

Hi Eric, you mentioned that some people say not to oil your air tools???? Really????????? If some one said that to me, after I fell down laughing, I would run away never consult them about anything....that is scary!!!!! Love your vids Sir....keep it up! Thank you!

@mudkicker7812 7 лет назад

Work at a bus shop, have a Cornwell CAT2135 1/2“ inch, IR Titanium 1/2“ and can say although the Titanium is more rugged and dependable, the CAT2135 is a monster. Only problem is I twisted the anvil off the CW. Since Cornwell insist on screwing there sales people over, I haven't been able to secure a replacement in like 3 years. Thank you Cornwell. My 1/4" air ratchet is a Central pneumatic from HF, it is 5 years old and gets the job done. My 3/8" ratchet is a Cornwell, it has been in my lower drawer since owning it, barely ever touch it. My most used tool is a 3/8" Impact wrench from Cornwell. It's a ballsy little fucker that just won't quit. Cornwell reversible whizzer, Mac 1/2“ drill, Husky 3/8" drill, Mac Air Hammer, in my opinion Mac Tools makes the best Air Hammers. Both my straight and angle grinders are Central pneumatic, after 7 years they work fine, although I never use the straight job. Swivels are weird on air tools, great when needed, but I the way when not needed. Sometimes the floppies can become a nuisance.

@nasirramli8658 3 года назад

Thank you Sir for your good Tuition..

@popupJunky 11 лет назад

Mac still makes you sealed head 1/4" air ratchet. I actually just bought one and love it.

@Ag_n_Mech 9 лет назад

A swivel joint for the air hose is a definite must have

@guitarwiz2000 11 лет назад

Great video!!!

@madjimms 11 лет назад

18v lithium tools are pretty badass. I'm jealous of your tools Eric :-D

@minilogoguy18 10 лет назад

If you're looking for an awesome 1/4 air ratchet Matco has the best, super small palm ratchet, great for timing covers and other tight areas. Doesn't put out too much power so you can tighten valve covers down with confidence without worrying about snapping small bolts.

@theshipyardtechnician2934 7 лет назад

I use ATF for my air tools. Works like a charm

@JUKE179r 7 лет назад

I got an IR 231C impact wrench (the older U.S. made one not China like the newer ones now) for $25 at a Georgia pawn shop. It's beat all to hell but still works great!

@johnfranks 11 лет назад

I got a Mac Tools AR1776 from the pawn shop for $30. Score! Its a beast! Swivel quick connectors help with the hose problem.

@Lorddarthvader1701 11 лет назад

This is a good size, runs whatever air tools I run, particularly the cut off wheels, it runs just fine, I run a 60 gallon. works like a champ

@spelunkerd 11 лет назад

By the way, Eric. Happy teachers day!

@christopherwilliams4647 8 лет назад

How often and how much do you use are you supposed to grease your ir impact guns?

@dmana3172 8 лет назад

I just stripped the screw for the caliper on both side and I would not be able to get it off. What tools do I need to get it off and replace it with the new screws? I was trying to put in new brakes, but I couldn't. Any advice would be appreciated.

@nialljamesbuckley 11 лет назад

amen on that damn honda crankcase pulley... i bought your timing belt video last year and i had to take it off again last month - STILL took a 5 foot breaker bar and everything i had to get that thing off.

@airbrushingbynick6071 5 лет назад

When You use the 3/8 ratchet do you use a larger hoze? That's what I'm trying to say dude.

@hondaguy425able 5 лет назад

Do you use 3/8 fittings on all your air tools? Also what size of air hose are you using?

@johnimburgia4321 5 лет назад

Eric, I noticed the impact wrenches and die grinders are in the yellow area on the compressor chart. Will a compressor of that size power the mini die grinder and impacts?

@russelljames417 6 лет назад

ETCG what brand of quick connects do you use?

@lajoyalobos2009 3 года назад

I seem to prefer corded or air over cordless unless it's for something quick and simple. Having both of your batteries go flat in the middle of a project is extremely frustrating, that or the fact that replacement battery prices pretty much mean getting a whole new tool sometimes. AZ heat may take a toll on battery life but it also means dry air and little to no rust.

@robin1987100 10 лет назад

Vertical compressors are nice, save a lot of space in a tight space + easy to move around. (i put mine outside when i use it, crazy thing produces like 98dB). Be sure to use large diameter hoses and large bore fittings, that really helps to get the most out of your tools. Not sure what pressures you can get in the US, but go for high pressure, you don't have to use it (most tools don't allow for it) but its nice to have it available. If only as buffer for the larger tools.

@robby844 9 лет назад

The tools I use see around 175-180 pounds everyday. Never had any issues with them. But then again I don't buy cheap air tools.

@robby844 9 лет назад

***** True, The first thing I always do is remove those dumb long tang air fittings. They drop a lot of flow. The fitting I use have a 1/4 inch hole in the middle. Anything above 10 SCFM requirement is a 3/8 hole fitting and my big tire guns have the glad hand style lock so there is no restriction.

@kws1957 11 лет назад

cool films, thank you, Winfried

@BillyBob-ld5nv 3 года назад

Erc! Nice air tools.

@Tecalitlan1943 11 лет назад

Electric impacts are cool when you go to the junkyard especially on cold days, I sure envy guys when I see them, the good quality ones are very expensive (Snap On +Ingersoll Rand). Craftsman electric impact has about 200 pounds, that sucks. Plus if it is not ion, the battery begins to die slowly when you need it the most. The newer IR impact gun is the 2135TiMax, I got it and I love it, replaced the one that you got in your video. Like you said, it comes down to individual choice. Great videos.

@SUPERJJMJ 11 лет назад

Thanks for the video I use marvel mystery oil mixed with wd-40 for my air tools

@ivansentanu3498 9 месяцев назад

2023 watching this video, really helpful

@GypsyHunter232UK Год назад

Excellent most informative

@RideForLifeCR250R 11 лет назад

I now have the MG31 snapon 3/8", used to have that same Blue point 3/8" impact which as you said the torque is weak.

@nialljamesbuckley 11 лет назад

what kind of bits do you use for your air hammer usually? i have a cheap little madeinchina air hammer that came with a pretty standard chisel kit - works well enough but does more damage because the bits are pointed - is there something else i should be using for automotive work?

@RobertSmith-di5ll 7 лет назад

really useful info

@gt40f 11 лет назад

The 3/8 impact is a CP badged as a Matco. The first 1/4" air ratchet Mac still makes that one. It has the thinnest head of all the 1/4" ratchets.

@1944johndeerel 8 лет назад

I just bought a Napa professional torque dominator 1/2" impact wrench and it's rated for 1200ftlbs break away torque I can't wait to see how well it works. I wanted something with more power than my cordless impact wrench I have a 1926 Champion 30 gallon compressor I am not using it for making a living like yourself but if it works I am a happy camper

@chrischiampo8106 7 лет назад

Can't take a Day off have to be there to oil my Tools Daily 😎👍🏼

@mikejens2271 6 лет назад

I've been used transmission fluid as air tool oil for years with no problems.

@tomgon9323 11 лет назад

Hey Eric, Lately I've noticed a lot more LED specifically Cree LED headlight bulbs coming to market what are your thoughts about these? Perhaps you could do a video comparison or just what you think. Thanks, Tom

@mabast007 6 лет назад

Hey Eric, got a question about my car. It is 2000 Avalon. The car shakes when it reaches 55mph. Before I took the car to a nearby shop, both have told me that you need tires. I suspected that would be the issue. The car, definitely needed a tire, but for that shaking didn't believe them. But I went and put a set of tires and still have the same problem. I have a break hesitation as well. What is this shaking come from? Thank you.

@Liamautomechanic 11 лет назад

air tools makes it easier on the old bones, saves a pile of tinkering, and time aswell. good vid there eric.

@Hammerman1234567 8 лет назад

have you done a video like this for your electric tools too, such as the Dewalt hand drill thing you used in the Pontiac Montana exhaust manifold video?

@Hammerman1234567 8 лет назад

Ive been thinking of getting some electric tools because I only have a very small garage to work in with almost no room for a big compressor or much room to maneuver hoses and whatnot, so what you said about freedom of movement with the electric tools really resonated with me. I found this video extremely helpful and informational and it would be amazing for me if you did happen to have a video like this about what sort of electric tools to look for.

@KAPtv 9 лет назад

Good show sir.

@acscolo 11 лет назад

Dragging around an air hose is a drag. I'm slowly replacing my air tools with cordless versions. However, I do think you need a 1/2 air impact gun when you really need the torque.

@Portuguese-linguica 11 лет назад

I love the dale ernhardt tool.

@shepd3 11 лет назад

I like that idea, I might just do it! :) I like the price, too.

@hobieslug45 11 лет назад

bought a cheap 3/4 gun from harbor freight. so far it took off honda crank bolts using the same air hose you have. a little oil does seal up the vanes in an air gun and can some times make the difference in breaking a bolt free.

@SZAPP68 11 лет назад

Eric, do you use a 3/8 or 1/4 air hose? How much power loss is there using the 1/4 line on your large impact?

@MossyOak83 11 лет назад

that is a genious idea putting the regulator on the air drill, i always get annoyed trying to hold a constant speed and burning up bits while drilling

@hondaguy453 11 лет назад

I remember I was trying to bust a crank bolt on my buddy's '94 Prelude, but wasn't able to until I oiled my gun haha. Now I oil that thing at least 3x a week.

@firebird22386 9 лет назад

your 3/8 impact is a matco i have the same one!

@mrspesul 9 лет назад

did you ever get those battery powered tools?

@hamiltoncouple01 11 лет назад

Hi Eric. I have a quick question regarding lower control arm on 2005 Nissan Altima 2.5L. I had a bad ball joint on my Altima, and since ball joint is part of lower control arm, so I replaced the entire unit. My old original ball joint had a cotter-pin, but the new one doesn't have it at all. There isn't even enough space above the new nut which is slightly taller, to drill a hole. I tighten the nut to over 50 ft/lb. Does is matter at all not having a cotter pin?

@dieseLmaN1193 11 лет назад

hey eric as an aspiring diesel mechanic i will obviously be using a ½ and ¾ impact the most wondering if you have any thoughts about craftsman impact sockets seeing as they are less than ½ of the price of snap-on

@epiphaknee 11 лет назад

Great video! Are you placing the lithium grease where the tool has stamped "oil here?" I think that one gun is an IR too. It is identical to the IR guns, probably as you noted just a licensing arrangement. I glad you did this video, I've been trying to figure out the brands with each video too! LOL!

@TOMA21207 11 лет назад

Hi eric, I have one question about air tool I bought few days ago. I do have air compressor and impact wrench that I intended to use on my cars but first day of use I run in to the problem. Impact wrench (says on the sticker) has all the power I need and air compressor has all pressure needed for air tools, but when I use impact on wheels I cant loosen bolts at all, and when I take it of with other hand tool I couldn't tighten it back with impact. Whats wrong(I set everything on specified max)?

@switchest26 11 лет назад

Im wondering if im too old to ask for this in my xmas stocking?

@MChappysGarage 11 лет назад

I have a problem with my 98 Buick lesabre, the issue is intermittent but most of the time the transmission shifts very oddly into 4th, It acts as if it does want to shift and then jerks a couple of times and then finally drops into 4th gear. Do you have any idea what the issue could be? Thank you in advance

@twig3288 6 лет назад

What size connector/couplings do you use?

@jtman04401 11 лет назад

Yes that 3/8 impact gun is built for Mac (and Cornwell) by IR. I had a TI2135 like yours and got rid of it and bought a Snapon MG725 to replace it. The ONLY reason is the Snapon slows down quicker when you let off the trigger compared to the IR which free wheels allot longer. I do miss my 2135 though. Those are the lightest best balanced 1/2" guns on the market with mega torque. I wish I had kept mine. I love my Snapon but it is quite a bit heavier then the IR.

@Shannon-zr7zp 10 лет назад

Hi Eric, I want to thank you for your videos you post... LOL Im buying my BF an Air compressor for christmas. I want to get him some tools to go along with it. I had no Idea what to to buy, nor did I know what an air compressor was used for.. Thanks to your videos I know a bit more about the compressor. Also I know what to buy him for tools, . So I just want to Thank you. Sales ppl can be a bit pushy sometimes who knows what they could try to sell me, LOL possibly somthing he would never use :) Now Ive got a little more insight. So thanks again... :) Happy Holidays...

@Johnlc081102 8 лет назад

You need a teflon ball-jointed drain valve on your compressor! I pieced together the brass plumbing needed to so that i could get to it with my foot so I don't have to get on my hands and knees to open and close the vent. Then again, I use my compressor very rarely though, so i open the drain to vent the pressure and moisture every time I use the thing, but the design of my Craftsman compressor is nearly identical to yours.

@antonkolding7563 8 лет назад

I work at a shop, where we use deblock oil, and we oil our air tools daily, all i can say for sure is, that the air gun itself wil outlast the grabbing ring

@firmamentsky 8 лет назад

How come you preferred industrial over automotive air fitting?

@nickl2642 11 лет назад

I Use PB Blaster to oil up my air tools, works fu##in fantastic

@Bmxerforlife206 11 лет назад

Could you do a video on hand tools

@dollman0 11 лет назад

I have used the napa tool oil and now am using lucas tool box buddy for my tool oil. the purpose of the oil is lube and it flushes out grime and deals with water in ur tools. The last thing you want it to get your air tool out and its rusted up solid, happened to my CP guns before. the grease lubes the hammer in ur impact to prevent undue wear from dry metal hammering together. the electric impacts are handy but kinda weak, the guys I work with have them because we do trailer work on big rigs

@jomach67 7 лет назад

This is good, I can use this new knowledge as sales of Air Tools @E-Smooth Industrial Trading in Philippines.

@ryans5565 4 года назад

the drill does not have a pressure regulator bro its a needle valve, you can call it that.. But its not the correct term.

@2billracemaniac 9 лет назад

I have a 60 in my basement, still have yet to wire it up but its winter and I have no projects atm anyways.

@austinmorris2638 11 лет назад

if you have time you ought to cover the first aid backpack you have in the background in this vid. Many people dont realize how important it is to have aid close to car work.

@franks551 4 года назад

Hey Eric do you work at home or at a shop ?

@shingleful 11 лет назад

Bostitch has a good hose called Prozhoze its light weigh and has no pull we use then only in construction & roofing, and yes we oil the guns every time we pull them out, we did not do that before and went thro a couple guns