Evinrude 9.9 Ignition Plate Explained 

You're my hero! Your detailed explanation solved my issue. Thank you sir! 🙂

Great explanation of the internal workings of a evinrude. I just picked up a 9.9 and I want to be able to do the maintanence myself, thisll help. Thx

Thank you very much for a well explained demo of the few extra components on this particular motor. I don't have a 9.9 but have been thinking of getting one and your video certainly comes helpful.

Best explanation on parts under flywheel and throttle relationship I have seen. I have seen testing videos on coils outside of driver coil but NOT the testing and relationship between the driver coil to test in relationship to testing the 2 cylinder exterior coils i.e. in a 76 johnson 9.9. If you can enlighten would love to see that video. Thanks for the very good video explaining the interrelationship & functioning of these parts.

Amazing video, thanx, i'm from buenos Aires argentina ando i have a 9.9 evinrude 1981, your video it's a great help For me!

60RPM would come out to 120 pulses. 2 pulses per rev. Yes, indeed advancing timing increases power, the real reason timing is advanced at higher speeds is 1 it runs better and 2 gasoline naturally burns slow. Advancing the timing at higher speeds allows complete combustion thus more power.

Man u know your outboards my friend. I am in a jam with a 68 8hp johnson. The throttle plate is way out after putting new coils in.. Ill have to try the nutral forward trick to make sure thats not the problem but i may need your wisdom if not.lol

Excelente video y muy bien explicado, ya me suscribi a tu canal y espero que pronto publiques los videos prometidos, Saludos desde Venezuela.

Great! Thanks!

Great video Thx

Great video. I have 86 6hp and the plate looks the same. I’m having no spark issues. The trigger on mine looks all burnt and nasty and so is the inside of the flywheel. Can these triggers be serviced and cleaned with sandpaper or replaced? Mine also has that same shoe y black goo under it like yours does. Thanks

Great explanation.

I think I seen the video of the guy with the starter on backwards.

Very helpful video

Great video thanks

Great information.. Jist today did i take my flywheel and found the same 2 electric parts conected under it..are these two enough for me to get electricity to recharge a battery ?

Great Thanks sir !

buenas amigo sabra donde va un fusible muy pequeño en este motor? se salio y no se donde van

What is the red plastic limiter arm called mine is missing the long piece near the ignition plate.believe it still functions but want to order a new one.very good content thanks.snooky pa.

@GolfCartSpeedyLink I have a problem. I just bought a 9.9 1978 and change the carburetor to a 15hp. I am not sure if this problem started then, because I barely run it . So here it goes: In order to turn it on when in neutral I have to accelerate all the way possible. It will turn on but be be barely a little over idle rpm. I can't really rev it up at all. I assume is maybe between 800 to 1000 rpms. So I just go down a little bit to make it idle smooth, which it does. When I put it in reverse, due to the restriction, it will only troll but I cannot accelerate anymore in reverse. And when going forward, I can accelerate, but I am certain that it doesn't reach more than 4000rpms or even less. To me, it feels like the acceleration starts too late(spark timing), so that creates all of these symptoms. Can someone direct me as to how fix/adjust that in these motors? Thanks in advance

Hello. I really need some assistance and recommendations. I have a 15hp 4 stroke long shaft fixed to my 14ft open fishing boat. So.. the engine starts after 2...3 pulls. Oh its made in 2001. After a 20min ride i anchor and fish. Want chage spots it wont start. Leaving it for 30mins it does but dies luckly near mooring. All fuel lines and carb are clean. It was suggested by the evenrude dealer i need a new coil. Any ideas most welcome. Oh taking the plugs out and pulling i get sparks ?

Great video, did you do one for the starter rewind?

I have a 92 Johnson 15 no spark and just found the ignition plate wiring is bad, looks like it was rubbing on the plate when it turns. Any advice?? Should I splice in new pieces of wire? Or just bite the bullet and buy a new plate for 300$?

amigo tengo un motor johnson sea horse 9.9 hp j10rcns 1982 queria saber si es de encendido o platinos? gracias

Great video and explanation.I own on of these and acouple of 25hp that I work on myself and since you are well versed on the timing maybe you have insight on a 25hp Johnson I have.Got this 25 well used motor and it has electric start and the stopper for the timing screw is mounted on the starter bracket.Someone notched out the bracket to get more adjustment from the screw and I cannot figure out why they would do this.Any thoughts?

my trigger on my 7.5 is almost across from the coil it runs but not right

Hola donde puedo conceguir repuestos

Can this system charge a battery if i add a rectifier?