F-150 Ford Performance Rear Differential Cover 9.75" 2009-2020 Installation

Подписаться 245 тыс.

Просмотров 40 тыс.

50% 1

Product Link: www.cjponyparts.com/ford-perf...
In this video, Freddy & the crew at CJ's will show you how to install this Ford Performance Rear Differential Cover on your 2009-2020 F-150 with a 9.75" Rear Differential from the comfort of your own shop or garage!
Absolutely American made, this Ford Performance rear differential cover is designed tough with long-lasting cast iron. Also, furthering the durable excellence of this cover is a rugged powder coat finish.
Far superior to stock, this cover absolutely eliminates case distortion and features incredibly helpful drain and fill plugs.
Check out more info on our SEMA Build here:
www.cjponyparts.com/resources...
Check out more F-150 Suspension parts from CJ's here:
www.cjponyparts.com/f-150-sus...
Check out more Ford Performance parts from CJ's here:
www.cjponyparts.com/ford-raci...
Subscribe to CJ Pony Parts on RU-vid here:
ru-vid.com_c...
Subscribe to CJ Off-Road on RU-vid here:
/ @cjbroncof150

Авто/Мото

Опубликовано:

4 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 51

@christopherbertolino2453 4 года назад

Remember boys and girls always hand thread the bolts first, don’t start them with the drill like Henry did

@FirstLast-ig2mg 3 года назад

Remember boys and girls it's called an impact wrench not a drill like Christopher said.

@topherb6403 3 года назад

I’m sorry, impact wrench. I’ve been doing mechanical construction for 20 years I’ll call it whatever I want, thanks for the clarification tho 😂

@cessealbeach 3 года назад

General Rule, Always hand start bolts, plugs and nuts, atleast 1/12 turns and dont use impacts on installation.

@elvism684 2 года назад

@@FirstLast-ig2mg Remember boys and girls it’s called an impact driver not an impact wrench like First Last said.

@atadbitnefarious1387 Год назад

Those reply is 2 years later but: Don't snug any bolts down until all the bolts are in place. That way if there's any tolerance in the holes, it allows you to shift the part around to fit all the bolts. If you snug down the bolts before they all go in, there's a possibility of the last few holes not lining up perfectly, preventing them from going in, or worse, causing you to cross thread them.

@THE_TURTLE. 4 года назад

You can get the same cover for like $130, it just has the Dana logo instead of the ford performance logo

@thomasdaum1927 3 года назад

The angle changes when its on the ground and the amount of fluid also.

@citizenpark2782 3 года назад

How does this compare to Mag-Hytec?

@brett639 3 года назад

Anything for 8.8 12 bolt? Looking for diff cover that has cooling blades.

@Dickj203 5 месяцев назад

Lower fill hole for just a leveling kit? No rear lift

@stidhamhimer 3 года назад

hold on, why does the same gearbox take a whole quart more oil when its at an angle? theres not more space in there right? confused on that one. looks like you overfilled

@danielgrabowski7419 4 года назад

Would this fit a 2007 model?

@noco2095 6 лет назад

I want one

@Blue_Flame_Raptor 4 года назад

4:15 it actually takes just under 4 quarts

@marvinbrannon6835 5 лет назад

I have a 2013 F150 with a Rough Country 6 inch lift. Do I need to use the top drain plug as you did for your 7 inch lift??

@eljefedejefes7469 2 года назад

I also a 6 inch lift and was wondering the same thing. I’ve always used the original drain plug on my stock cover and now have purchased those ford performance cover.

@Blanco_5.0 Год назад

My rear axle is 3.31 so is that the 9.75 or 8.8 ?

@jve5280 3 года назад

Lifting a truck with blocks in the rear doesn’t change the angle the pinion sits at in relation to the ground in any way. You would have to cut the saddles off and re-weld them in order to change this angle. The drive shaft angle changes but that’s it. If you follow this advice get extra axle seals, you’ll be replacing them on a regular bases.

@Eatmypho 5 лет назад

Torque specs of 14 ft lbs seems pretty light. I thought it was 33 ft lbs?

@globaloutreach7523 3 года назад

20-25 according to the instructions.

@yruhatin100 3 года назад

If you reuse original bolts then it's 35ft-lbs. New bolts that come with cover call for 14ft-lbs and will break at about 30ft-lbs.

@Army4Runner 2 года назад

@@yruhatin100 Instructions state 20-25 ft.lbs. I recommend the 14 ft.lb number. I busted one of the bolts at 20 ft.lbs.

@user-yt1vf1qj7t 10 месяцев назад

I did my Dana Spicer cover today. Reused factory bolts, had them all at 20 ft lbs. Found torque spec for 35 ftlbs, second one snapped off 😒. 2013 F150 8.8", left the rest at 20 ftlbs. At 38 yo, I'm retiring from this DIY 🐃 💩

@daveedward6925 4 года назад

How come fordtechmakuloco torques the cover bolts to 35? Why do u guys only do 14?

@yruhatin100 3 года назад

If you reuse original bolts then it's 35ft-lbs. New bolts that come with cover call for 14ft-lbs and will break at about 30ft-lbs.

@SHADOWBLACKs650 6 лет назад

What's the green plug on the side of the differential housing?.... As the first time I've seen wires coming out of a gearset.

@MarkDanyluk 6 лет назад

09victoryrc connector for Electronic locking differential

@SHADOWBLACKs650 6 лет назад

Thank you ,that's pretty cool.

@diverbelow27 6 лет назад

MarkDanyluk that’s what I thought . That’s the Ford oem one correct ? Not eaton

@LinhNguyen-nq5di 3 года назад

Excellent video! Is the front differential cover the same part number as the rear diff?

@thomasdaum1927 3 года назад

@czts4778 4 года назад

Is the cover made of cast iron or aluminum? Some specification online said its aluminum. Thanks

@americantrucknation4891 4 года назад

0:28

@rich-tx7473 Год назад

75-140? Recommend 75w-80

@chrishenderson6642 5 лет назад

Don't need any sealer on new 9.75's , just re-use the oem gasket, it's easy as pie.

@FordTruckGuyKyle 2 года назад

Do you recommend this differential cover if you tow heavyweight with your F-150

@dontask8979 4 года назад

You dont add 2 quarts just because it's at a angle.... If your going down a steep grade, are you going to drain some back out? NO Every china cover I EVER saw, had the wrong fill locations. "They" usually have two, and give the same story. The difference is high pinion or low pinion. 14 ft lbs? and using a gasket... tells me I have about 20 years more time in axle work. If the book calls for 8 pints, use 8 pints.

@Neoviper240 5 лет назад

Did y’all use sealant with the gasket? You do not mention it but it’s visible at the end of the video.

@cjponyparts 5 лет назад

You don't need to use sealant with the gasket, I believe our gasket somehow got damaged during the install and that's why we used sealant and didnt mention it.

@wiscoric2695 4 года назад

@@cjponyparts Why did you not use 75w85 gear oil on that 2018 pickup???

@daniejw 6 лет назад

Is there any difference between this cover and the one that spicer sells that doesn't say "Ford" on it?

@FirstLast-ig2mg 6 лет назад

Of course, the Spicer version is the original manufacture and Ford just pays Spicer to make their "Ford Performance" version which you can buy for 70$-80$ more to have "Ford Performance" on the plate instead of it saying Spicer :)