Felder CF 741s - Shaper mode spindle swap 

Thank you for watching! When I purchased this machine there wasn't a lot of available information on how to use it. Felder tech support was alright but over the phone left a lot to be desired. That is one of the reasons I started this channel. I will do more walkthroughs and I have a video review/pros and cons of my experience planned. Cheers!

@@ebwoodworking Hi 👋 EB , I am now 71 years young dude retired English gentleman ha ha, I still have most of my tools, but I had to sell some Machinery back in 2019 due mainly to my female partner scamming me, I had spent all my savings and income on Two renovation projects one in UK and one in France, That is a very bad story as I am still trying to fight a case against her, As France was where we were supposed to be retiring to I decided to move here, To make sure I was covering myself legally I went to the police and went to a solicitor for advice, So this is where I am now living, My basement is now my workshop which is very small approximately 7 m x 12 m, As for my workshop back in the UK was an old grain store approximate 8 m wide at 35 m long I could drive my vehicle into it which is very good respect if it was pouring down with rain I can still load my van or unload it which ever I needed to do, Anyway going back to my work there was another piece of kit that I purchased just after I got my machine I cannot remember who makes it but I believe it’s made in Germany it’s a shroud that goes over the top of the spindle moulder that allows you to run jigs either a bearing on the main shaft or aluminium plate that is fixed to it, I would make a jig either out of plywood or MDF I will spend a lot of time on preparation on these making sure they were very very smooth then I would fit stock blocks and clamps onto them so the piece of wood that I was going to profile was well secure, Most of my clients were very high end though sometimes I had problems with some people saying why do I charge so much for doing a job or contract and then I try to explain what it cost my rent and rates and electric on my workshop, And the cost of my machinery and the main maintenance all the machinery as well, Considering I was a one-man band ha ha can’t play any instrument I wish I could, I reckon that it has cost me somewhere in the region of £70-£100,000 if you had to go and buy everything brand-new I was lucky in some cases I managed to purchase some bits of equipment secondhand then I rebuilt it. Wadkin EKA 4 head , that dates back from 50s . A very old mortising machine, from the same time period, In some cases order machines are sometimes better than new machines as they used to be made out of cast-iron which made them very heavy and more substantial, Good luck in your career, And Be Safe, Especially when it comes to your lungs and your ears are used to have a piece of of safety gear made by M3, It is quite expensive it has a air Feed mask and it is built like a crash helmet With a polycarbonate face shield and ear defenders, Especially very good if you’re doing Woodturning, I look forward to your next territorial open all goes well, PHIL FROM THE DARK SIDE OF THE MOULIN FRANCE.

No problem. I'll do that soon. Cheers!

Absolutely. It takes some getting used to, but if perfect for a 1 person professional shop. Cheers!

Right on! I love my machine. I do custom woodworking by trade and even though I am a small one-man shop, I still want industrial-quality tools. This machine fits the bill. It has its quirks and there are a few things I would have liked to have known before buying, but all in all, it was a great investment. I'll make a review video for it soon. Cheers!

@@ebwoodworking thanks for your time. I am also a one man professional shop, though my primary livelihood is and has always been as a piano player. With that in mind I think sliders are in most regards safer machines, and as I’m 66 now, I’d like to maximize my enjoyment and safety the years I have left with my woodworking trade. I truly don’t expect you to enter int a never ending dialogue with me, but if you ever can find the time to note the quirks you mentioned, I’m all ears. I currently use a saw/ shaper and 12” J/P both from Felder. I run a 20” planer as a stand alone and will likely not use the thickness planer but want the upgrade to 16” jointer with helical head. There are some known improvement in your machine that I’d enjoy that aren’t on my model. Anyway, I’ll look for your review,and again, thanks for your time.

Hi EB , A GREAT Territorial on the Felder CF741S , I have the same Machine I purchased back in 2005/6 I think, I will have to go and have a look, I to I’ve got the same accessories as you including the router shaft it is an excellent bit of kit, When I purchase mine I had the motors upgraded I can’t member whether they are now 7 hp or 10 hp, . I am now 71 and retired English gentleman ha ha, living in France, I am a self-taught specialist joiner cabinet maker, And over the years I have made tables chairs furniture bookcases though in the last 1012 years I have been mainly involved in making specialist windows and doors and staircases for high end Barn conversions, I have specialist window tooling set’s to fit on machine, I do have a Wadkin EKA tenner for doing larger windows and doors, I do wish I was back at work, Thank you for your Territorial on the machine, Keep up the great work and please be safe, PHIL FROM THE DARK SIDE OF THE MOULIN FRANCE.

I love my machine. It has some quirks, and I, too, had some issues when first setting it up. I've been wanting to do a video about the experience. Hope you got it sorted. Cheers!

Hello! The router spindle on my machine uses an optibelt-RB PJ 533. Hope that helps. Cheers EB

Thanks eb I will check it out Regards Liam