Ferrite Transformer Winding For INVERTER 2022 / 500W and 1000W 

You should use litz wire for 230v side and copper sheet for 12v side. Wind them : copper sheet 12v, 230v litz and copper sheet 12v.

Good day Sir. In the primary winding, both 3T go thé same way around thé center tape ? Shouldn't they go opposite direction ? Thanks.

Very nice Guide Respactabile Sir i appreciate for you Frome Pakistan Karachi Gizri CLIFTON Muhammad Khalid khan Electronice Shope Thanks a lot,s Respactabile Sir

Hello, I want to make a transformer for an inverter with your formula. Does this transformer really work and give real 1000 watts?

At *minute* 1:38 How long did you *boiled* that water? (If that was the case)

very practical very good, can I use the same winding and the same gauge of wire when using the EE 35 atx ferrite? thank you

How did you know the transformer and wire gauge calculation

Super. Ferrite core eka air gep eka thiyena ekada air gep eka nethi ekada ganne.

Pls again how many numbers of the turns for the primary winding

How can you parallel 2 of 1000watts transformer to make it more powerful

නිකන් කරකවනකොට වඩා ඩ්‍රිල් එකකින් විදිනකොට වගේ Load එක 1 1/2 ගුණයකින් විතර වැඩිවෙනකොට මේක රත්වෙලා හානි වෙන්නෙ නැතිද ? කම්බි තට්ටු අතර ලෙදරොයිඩ්, එම්පයර් ක්ලෝත්, එලයිට් පේපර් වලින් පරිවරනය කරලා හිස් අවකාශ ශෙලැක් කරන්න ඕන නැතිද ? බැටරි චාර්ජින් වලටත් Ah වලට ගැලපෙන තව ට්‍රාන්ස් ෆෝමරයක් හැදුවනම් වටිනවා නේද ?

Hello, this inverter is from 12VDC to 220VAC?

PRIMARY (for *500W* ) made with 60 Turns (vueltas) Cal. 20 SWG / SECONDARY transformer: (Two bobbins) One made with (4) paralleled coils of 20swg, with 3 turns and, the other, opposite winding, alike the first (as it was a *Thief of Joules* ). The one + the one, serve for those 1Kwatts

Aiye mn gawa thiye inverter ekaka oya wage transsfomer 2k e deken mokowath wenasak nokara oya wade karanna puluwanda

මේකේ hz ගාන වැඩි එක් ප්‍රශ්නයක් වෙනවද? 4027 ic එක දාලා හදන inveter එකට මේක use කරන්න පුලුවන්ද?

Cane u help me to make a ferrite core (pc40) transformer for 1000w high frequency inverter

Gold job

නියමයි. ජය වේවා....

Please sir what is the diameter of the core,E35, E37 E42

ඉතුරු ටික එනකල් බලන් ඉන්නවා. පට්ට.!!

1:00 mekath high frequency inverter ekak da

Please share video for 1000w windings And describe data also

👍👍👍බොහොම ස්තුතියි 👍👍👍

Very good

20swg කියන්නෙ ඒකෙන් ගෙනියන්න පුළුවන් ඇම්පියර් ප්‍රමාණය 2.03A වේ.. එතකොට secondary එක 920VA.. primary එක winding කරන්නෙ 20swg කම්බි 4ක් පැරලල් කරලා ඒ කියන්නෙ ගෙනියන්න පුළුවන් ධාරාව 8A.. 12v 8A ක් දීලා 1000w ගන්නෙ කොහොමද out එක.. ඒක පහදලා දෙන්න මම වැරදි වගේනම් නිවැරදි කරන්න

What are the reason for high noice (hum) on rewind transformer, any specific reason???

Puedes describir cada uno de los bobinados de cada transformador?

❤❤❤❤❤

Can I Charge the Battery of the Seem Transformer?

ferrite core is it work on 50 hz

Tanks

Supirii

1000w walata secondry widing eka 32tun da othane? 500w walata 60tun da?

How you join two transformer. Circuit diagram please

It will heat up the MOSFET faster an can even damage it

Smps transformer calculation කරන්නෙ කොහොමද

Can you tell me the rest of the inverter or not, give me a full video

why you use two transformer for 1000 watt. why not one transformer? is it not possible to make 1000. watt by one transformer?

දෙවෙනියට test කරල පෙන්නන inverter එක 1000w එකද අය්යෙ 😍? modified sine wave නේද ? ඒ වීඩියොත් ඉක්මනටම ඕන 😊

Sir clear kise na sahi real video hai na thaki ham bhi vasa banaaye please sir

Ferrite transformation more information

Okata h bridge eka onemada

Supiri. Inverter eka hadana eka ikmanta danna

For 50watt please.

Does anyone know if this channel reply to comment or it’s not and e

😀100%

Well, I am a totally amator and never done something like this, but I was learning a lot, and your video is useless without proper information. Whoever watch it, and want to make something like this, they most likely fail because winding a ferrit transformer need much more information like, operating frequency and many others. There are a tonne of more proper video that actually helpful. You only show how to wind wires. That is not knowledge. Everyone can do. I am sorry, but you should share more information, like that I mentioned. Operation frequency. For example. I am looking for a transformer 2x12V to 110V at least 2Amp of loadablility working on 600Hz and maximum 1800Hz. However, your video doesn't helpful at all. Please updated the description of your video, to help more people.

5 o 5 turns

Without calculation it becomes garbage 😂

.namal. supiri