FJ Cruiser: 5 Min Removal of Center Console and Switch Panel

Подписаться 18 тыс.

Просмотров 102 тыс.

50% 1

Other FJ Cruiser videos:
My camera setup (front/rear): • The FJ Cruiser Ideal C...
Fender flare installation: • FJ Cruiser fender flar...
Cowl clip replacement • FJ Cruiser Cowl Clip R...
Center console removal in 5 minutes • FJ Cruiser: 5 Min Remo...
My future mods talk video • I bought an FJ! (mods ...
It is very easy to remove the center switch panel. The center console will need to be removed first. Follow this video or the steps below to remove it.
1) Chalk the wheels to prevent the vehicle from possibly rolling away
2) Remove the drink separator in the back of the center console
3) Unbolt the two 10mm bolts beneath it
4) Unscrew the shift knob (manual trans) and 4wd selector
5) Pop out the cover beneath the emergency brake
6) Lift up on the lower plastic piece so that it clears the emergency brake.
7) Move the drive and passenger seats forward
8) Turn the lower center console plastic so that it sits longways (front to back) between the two seats (passenger side faces down, driver side faces up) then lift the plastic cover from the front to stand it up. Place it in the back seat
9) Unbolt the two bolts behind the shifter after lifting the plastic cover
10) Unbolt the two bolts under the switch panel.
11) Press in on the center of the plastic snaps at the left and right of the switch panel (near where your calf muscle would be on your leg as you are sitting in the seat normally)
12) You can now pull out the switch panel to remove any switches, switch blanks, or to run any wiring behind the switches
13) You now have access to the rear of the switch panel.
14) To reinstall, follow the reverse order of what is above.
www.hournineracecraft.com
#FJCruiser #fj #toyotafjcruisertrd #toyotafjcruiserrecoveryteam #fjcruiserrecoveryteam #fjcruisertrailteams #toyotafjcruisers #fjcruiserus #toyotafjcruiser #fjcruisers #fjcruiser_allterrain #fjcruisertrd #fjcruiseroffroad #fjcruiser4x4 #myfjcruiser #fjcruiserlife #fjcruiserallterrain #fjcruisernation #fjcruiserdaily #teamfjcruiser #liftedfjcruiser #fjcruiser_world #toyota4runner #modified #modification #modifications #modifiedcars #leds #led #ledlights #offroadlights #foglights #rooflights #wiring #electrical #relay #relays #electricalwork #solder #soldering

Авто/Мото

Опубликовано:

26 июл 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 70

@warrentaylor1651 7 дней назад

Still helping 7 years on, have the Aussie FJ with auto and your video helped heaps - Thank you

@jacobhowlett5232 7 лет назад

This is a GREAT tutorial video! The part that amazed me was you did it all with a camera in your hand, NICE! Somebody sponsor this guy and send him a tri-pod!!! Great video. Thanks.

@m1cajah 5 лет назад

Got so excited when I saw this video. Thought for sure I'd have that iPod connector in mine (it's the base model with all the higher-end convenience packages). Nope. Darn it. Still a very good video - when it comes to running some connectors I now know how to remove the panel! Thanks a lot for posting it. Edit (08/2019): Wanted to let you know this was quite helpful today as I installed a new Alpine head unit and needed to access the parking brake wire. Easiest way to find it was by removing the center console. In, tapped, tested, and reassembled in under 20 minutes. Thanks again for this tutorial!

@michael184272 7 лет назад

another great informative instructional video... thanks for posting... kids spilled milk last month...heat and milk..now I will comfortable getting into console to muck out... thanks

@dalejones4322 3 года назад

Thanks man. This made it so easy to do. I am one of the guys who has trouble reversing things lol. I have the automatic and it was easier to do. The bottom part of the console doesn't have to come out. You just have to slide it back. Great video

@LegitRaceCraft 3 года назад

Glad to hear!

@theopiechotagoncalves7534 3 года назад

Nice video. I like how you did the cameras.

@jla3772 6 лет назад

I have an FJ exactly like yours and this is just what I needed to know to change out my charge port. Excellent video. Thanks

@flyingpig7203 2 года назад

Thanks for the tips and tricks.

@smug247 3 года назад

Thank you this helped alot great video!!

@jerrymarques9202 6 лет назад

Super video, thanks

@HouseDrone1 7 лет назад

Im hoping some one does a rear camera install ,im not sure what wire triggers the reverse on the shifter

@POPPASHANGO 7 лет назад

Great vid keep them coming. If I may add a tidbit of info. I installed a rocker for my off road lights in the panel. But I went a different route. I removed the cowl around the radio, the radio and heating controls and reached down inside through the opening. Ran my wire through the pushed out the blank I wanted to use and attached to my rocker. Snapped the rocker in and re installed the radio. Both ways work well. FJ's are very well thought out as far as working on them.

@theflyfishnut 7 лет назад

Hey - When I install my Bumper with fog lights in this week - what would be the best way to run the wires to a rocker or push button for them?? And does Toyota stock these buttons or should I get from a 3rd party? Thanks .

@LegitRaceCraft 7 лет назад

@theflyfishnut, I'll be posting a video within a week or two on installing my lights, I got my switch and fog lights in the mail a few weeks ago. I have relay wiring tutorial videos that show how to wire basic lights through relays, and it would apply to fog lights also. I'll reference that video in the new video. I don't know if you can get them from Toyota in stock, but you can definitely buy the Toyota part online. Be careful if you buy the switch online though, there are rocker switches (ARB/Carling style) that won't fit into the Toyota switch hole. You would have to buy switches that are made for Toyota hole and I forget the exact dimensions. The ones I've been buying have amber or orange lights on them so they match everything else :)

@CiscosDisco22 5 лет назад

Great vid...thanks heaps

@javyLSU1 8 лет назад

Do a video on the monitors! I'd love to see what hardware you chose, and how you wired it up, I'm getting ready to wire up a front facing camera on my FJ.

@LegitRaceCraft 8 лет назад

they are cheap Amazon cameras. a friend had some extra ones and he gave them to me. I'm planning on moving the front one to above the driver door facing down. then I'll add one or two more so I can see the sides of the vehicle. I ordered some wide 305 tires so I'll need to see the sides when parking since our parking spots are so narrow here.

@reconn3cted276 9 месяцев назад

Thank you

@JasonJemVideo 2 года назад

Thank you very much!

@kenboden9589 2 года назад

Thanks man!

@ryansmyth7598 2 года назад

Thank you for telling us the ground wore color but WTF is tha acc wire color…

@pinay56 6 лет назад

With all of the blank switches, how did you determine what they were, and how do you connect an appliance such as a light bar, hood lamps, backup lamps to that particular switch.

@LegitRaceCraft 6 лет назад

+Cameron Garcia there were only two wire plugs after I removed the switch blanks. I googled a little and found out one was the atrac switch and the other was either subwoofer control or auxiliary power button. The other blanks were just a plastic cover with no wires behind them.

@csimarron 5 лет назад

As always. Very helpful video . FYI. I install a USB port accessed from the stereo panel. Question: what are those 2 existing blue connections in the panel?

@LegitRaceCraft 5 лет назад

It could be for the auxiliary outlet wiring in the back, subwoofer, roof lights or ATRAC. I think there are other options. There is a diagram that pops up on the FJ cruiser Facebook page occasionally that shows the location of different switches, so the plug SHOULD be in the appropriate spot for whatever switch was in that location.

@MrPallwaul 6 лет назад

Any chance you might know how to remove the shifter? I finally bought the FJ I told you about awhile back but now it's like stuck in gear and I'm trying to check the stick to see if something is stuck in there. Even in neutral if I let off the clutch she'll just stall for some reason. :[

@mr.hollingsworth9224 5 лет назад

Good video. Just picked up an FJ the auxiliary port not working do I need to hook that up or you think it's burned out anyone?

@FFKiwi1 7 лет назад

Hey brother. Great video. Before i start putting in some rocker switches, may I ask you - do all of the "blank" switches that came on the panel have wiring behind them already? as a nice convenience that i would only need to buy switches?

@LegitRaceCraft 7 лет назад

+Lisa DeMayo that would be nice, but no. There was only one other switch blank with wiring behind it and i don't know what it goes to. Most of them are blank.

@gonzosc1 6 лет назад

I have been looking to buy an FJ and I'm researching all the options and stuff and I've watch your videos. I see that you just added the Atrac switch. do you know if all FJ's are like this. where the Atrac is there but just needs the switch if its not there already?

@LegitRaceCraft 6 лет назад

+gonzosc1 I'm not sure, I would guess that they are, but I can't definitively say. My friend just bought an automatic 2012 version, and it had the atrac button already installed, so his auto version has it, so I would assume that the automatic 4wd versions that didn't come with atrac would have the wires there like mine did. That's all I know

@ChuongNguyenCGoogle Год назад

Thanks for sharing bro. Do you mind if I ask you have video showing how to wire front and side cameras? Im looking for installing them for my FJ, so i can get clear view when park a car or driving off road away the rock.

@LegitRaceCraft Год назад

Thank you for your comment. I actually made a video already on the camera setup ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE--q9Uxx7st48.html

@jsantospm 3 года назад

Got a question if my Fj doesnt come with the compasss on the the dash can I install one with out buying a dash for it?

@LegitRaceCraft 3 года назад

Yes. I bought one that I'll be doing an install video on soon

@AlbertAguirre 2 года назад

What kind of camera system would those monitors? I really like that, what brand is it?

@LegitRaceCraft 2 года назад

Honestly I don't know. They're off brand on Amazon, very cheap but they had good reviews

@109harold 8 месяцев назад

Can you pop the switches out without taking all that apart , I just want to replace the fog light switch

@LegitRaceCraft 8 месяцев назад

Yes, you'll have to very gently though because the plastic will get tool marks on it. Use a plastic pry tool if you have one, or be very careful with a small flat blade screwdriver. Pry forward gently at the top and bottom and it should slip out easily

@Rashed2030 5 лет назад

I think only auto gear in usa never used manual i will by this day fj manual ansallah it will be great

@vernonstickells2490 Год назад

Can you Plse add details how to order accessories from Japan ?

@LegitRaceCraft Год назад

Search for the part number

@RobertOrtiz1015 5 лет назад

How did you mount screens up there?

@LegitRaceCraft 5 лет назад

A flat metal strip of aluminum to attach the screens to each other and then I zip tied them to the mirror post so I wouldn't have to drill into anything

@RobertOrtiz1015 5 лет назад

HourNine Racecraft dang! Genius! Thanks! I like it more than on the dash! We already have a small windshield... dont wanna place anything else uptgere

@chrisfort7340 2 года назад

Great video! What cameras did you install? I like’m!

@LegitRaceCraft 2 года назад

Cheap Amazon cameras, I have more I'll be installing in the next couple weeks since I'm upgrading the system

@crazyanloonley 4 года назад

Do you have a video or any info for the camera system nice set up by the way

@LegitRaceCraft 4 года назад

I should make one. I've changed the backup camera setup since this video and used a cheap head unit that stopped working. Now I need to revert back to what's in this video

@crazyanloonley 4 года назад

HourNine Racecraft thank you so much I’ve just started my built on my 07. And i really like the camera setup and i can’t find any info on how to install

@abcalfie11 2 года назад

hi bro were can find diesel fj40

@LegitRaceCraft 2 года назад

The fj40 is called the bj40 if it comes with a diesel engine, and those were release in many overseas countries. To get the engine you would have to look for the bj40 engine overseas and have it shipped, the easiest place would probably be Canada if you're in the United States

@jamesdeluca4035 7 лет назад

Great vid, sweet FJ. Is it possible to add an aftermarket ATRACK switch to a 2008 FJ 4x4 with a 5 speed automatic and no rear dif lock?

@LegitRaceCraft 7 лет назад

+james deluca to my knowledge, no. You need the rear diff for the atrac system to work

@jamesdeluca4035 7 лет назад

Yes, just as I thought. I'm in the market for an FJ Cruiser and I found one on Cargurus to the likes of my above discription, but no atrack is a deal breaker (I think). Since I do plan on owning an FJ, I did subscribe to your channel because your detailed tutorials will be very helpfull. I welcome any tips for someome in the market for an '07 or '08 FJ. Mahalo bra.

@TheOceanX 6 лет назад

You don't need the rear diff for the A-Trac; A-Trac purely controls your brakes. It applies brakes independently to whichever wheel is slipping to give the other wheel more traction. I believe there is a kit available to add A-Trac to vehicles not equipped with it. Check purefjcruiser.com/ They typically have all my FJ needs in one place. (I do not work for them and am not advertising for them lol)

@christophercase7140 Год назад

So if you have the atrac wiring connected to the switch but no atrac what is the other end go to? Can I tie into them for something else?

@abcalfie11 2 года назад

engine fj40 deisel

@user-ey3kk4zv2t Год назад

Из-за перевода ни чего не видно

@TheJ3builders 4 года назад

or you can just remove the stereo cover and access it from the top. It will save you a lot of time. Removing the console in completely unnecessary

@tomlee6263 2 года назад

10-4

@dalemacdonald201 Год назад

If you need to get to the bottom bolts for the switch panel so that you can access the back of the switches, you need to remove the centre console.

@georgebankseditor Год назад

Talks too much but good tutorial

@kratos1011000 5 лет назад

Dude just get a camera stand, all this motion making me sick

@enginjass 3 года назад

Very bad work...

@enginjass 3 года назад

Cables everywhere

@stevegowan1282 9 месяцев назад

Why do you have it in for high supposed to run in too high

@LegitRaceCraft 9 месяцев назад

Manual fj cruisers doesn't have a 2 high option, it's full time 4wd, so it's always in 4 high and there's no way to take it out of 4 high

@stevegowan1282 9 месяцев назад

@@LegitRaceCraft That's right, you did say it was a manual, I'm sorry. I'm learning LOL. But mine does have the a track wired already from the factory Purchased the button.