@Zachariah Peterson sir it is perfect for a 15min video, thank you so much. I think the component selection and more details about opto feedback (especially tl431 usage) and snubber in another video would be diving deeper :) and the crucial part EMC filter and some layout tips deserves another video :) what I'm wondering is how do we add current control to this circuit.
Perhaps not a "deep dive," but still a very good explanation of a simple flyback PS. Worth the 15 minutes. One can spend an entire semester learning switching supplies in detail.
I do believe the ground reference used by the bridge mentioned at 04:54 is the same as the ground reference used by MOSFET. As far as the isolation goes the same is provided by the transformer.
Yes they are the same reference, don't mind the symbol difference, and yes transformer provides isolation which is why I did not put a symbol there but just a negative terminal for an output.
IS it really a transformer and not a coupled inductor? asking since i remember you needed an air gap. I tried to build one in the past but the hardest part was the transformer* part since most out there are built on order and figuring out the proper generic part out there was the hardest part, maybe you can expand on this on a later video. Or how to make one from a toroid. Also what is the switching frequency range for flybacks ? buck boosts can go up to a few MHz but I never saw any flyback that was even close , also what would be optimal from a efficiency point ? Does the transformer* limit the switching frequency ? Regarding multi output one i have a few questions: 1 how will the power draw in one affect the other? As in if from the 12v DC rail we draw .1A and then 1A how will this affect the 3v3 rail? the rail with the FB will be ok but i am afraid of voltage saggs on the other one. OR should i size the other one higher and then use a LDO after the diode? 2 can i set a center tap like GND so that i also get negative voltages? 3 If i would desire a few DC rails with the same GND wouldn't it be simpler to make a higher DC single rail and then add a few LDOs or bucks on that DC line? (not sure about cost but i assume it is more expensive at scale)
It's absolutely a coupled inductor in flyback supplies; it's where the name comes from - energy "flies back" - magnetic flux is built up in the core during the primary on-time, then collapsed into the secondary(ies) in the off-time. Each switching cycle transfers a "packet" of energy; the size of this packet is proportional to the inductance and square of the current. Since the time it takes to ramp up the current is proportional to the inductance, it's more beneficial to lower the inductance to increase the current. This does however result in high magnetic flux, which is why flyback cores are either gapped, or a powdered iron core is used (which effectively has a distributed air gap, allowing for higher flux before saturation). You can only decrease the inductance so much before current levels become unmanageable, so between this and other factors such a switching losses, there's a "sweet spot" for the flyback topology, which is why you only really find them in the sub-200W power range; above this, a design using true transformer action wins (eg. forward converter, half/full bridge)
Forgot to add re: multi output. You'd take your feedback from the output rail that needs the tightest regulation. There's nothing stopping you adding linear regulators afterwards, but if you're doing it because you want a really clean output, you'll need careful L-C pre-filtering before the linear regulator, as they aren't very good at filtering out the high frequency components of the switching noise that the flyback will generate.
@@NicBellamy So if i use some of those powdered toroid's i can wind the inductors and not bother cutting into it? NICE But i am still a bit clueless about how to filter out the good ones are the powdered materials from a certain series or is the a material number range? asking since i am a bit lost on mouser
If by "reference" you mean the AC equivalent of a negative terminal for return currents then it would be neutral. The protective earth is connection is not meant to be a current carrying conductor so it should not be used as such. It is useful to provide a safety ground using the chassis, or by drawing an earth ground ring around the edge of the board.
I came up with CRT televisions that had HT (frequently on the order of a KV) flyback converters. Could you relate this to your low voltage applications?
Can we use full-bridge rectifier on the output? I never seen that, mostly there is a center-tap coil for secondary and two diodes on both end. I guess because the few turn of copper is much cheaper then two fast switching power diode, but I'm nut sure. Is there any other reason why it is unusual?
I suppose you could but I have never seen it, I would need to think about it. I do recall seeing center-tap coil designs on the secondary side, and to rectify both would need diodes, but I see it more often when you want two output rails or in a full-bridge topology.
