Ford Mondeo MK4 1.8 TDCI, injector replacement. 

What a great video. Thanks for upload. I have managed to replace all 4 injectors in my Mondeo mk4. I’ve used brand new parts from PF Jones Ltd. Great communication & postage. I have save huge money by doing it myself & now I’m drinking beer 🍺

Thank you so much! Mine was #1 injector what was failing, but these intructions worked more than fine! Getting no errors after replace. First i had small air leak, but i readjusted injector and leak was gone ! Thank you

Thank you for this video, it helped me to do this repair and my van is no running fine again. It started on the first turn of the key

Thanks didn't think it would be this easy actually. Probably on a note I'd replace the injectors one at a time and turn the car over so that u don't have to reprime the fuel pump because I'm lazy haha. Glad to know that these engines make a lot of ticking as normal too.

Excellent video, replaced leak off pipes and leaking Injector from watching, thanks!

Hi I was assembling everything back and the plastic nozle doesnt want to go back, I tried fitting it back to the old injector and also doesnt want to go back in. Any advice ?

hi! I have a problem with my Ford Transit Connect 1.8 TDCi 81kw. namely, when adding gas or accelerating, the engine jerks until I let go of the gas pedal! and it happens very often. Is it the injector in question because it is quite wet from the diesel!

Very good video. No messing about. No rubbish music. 👍👍👍👍

Just found diesel pissing out from one of the injectors on my engine. Your video really helped me sort it out. Thanks very much!

Hi I don't use this very often but like what I see. I have the same engine but in a ford galaxy mk3 1.8 2009. I have air in the System And having trouble bleeding it out have you got any help look you can give.

Great video 👍 Seems easy enough job for me. How about torquing injector bolt? Do you know torque specification or is it just "hand tight"?

did you not have to clean the seats where the injector sit in. just bit or compressed air and whack in new one ok then?

Is not necesary shutting down the current before this work??? Thanks!

Вот тут на видео звук такой "керамический", это звук того что форсунка немного подстукивает?

Hi, my Transit connect 1.8 has the same engine (looks the same) and feels like it's running on 3 cylinders. The code reader shows code P1201 - Cylinder No. 1 Injector Circuit Open/Shorted. The engine won rev past 1400 rpm and there is no power.I have been told that these engines are a pig to bleed once a new injector is fitted, your car started easy though ?

Did you have to code these in after fitting

Большое спасибо У меня такаяже тачила. Стоит ли чистить инжекторы для профилактики или в надежде что поможет с излишним расходом топлива ? Большинство источников говорят что избыточное потребление топлива , в моём случае 30% из за кислородного сеснора Думаю его почистить, или поменять и инжекторы только почистить так как они дорогущие ты говоришь 160- 200 за один

What you think about 1.8 tdci ? It's une good engine? Good choice for Mondeo?

Hey, good job, did you write new injector number in computer?

I've just replaced injector 3 following this guide but its leaking from from where the injector goes into the engine and i can push it down with my hand to stop it leaking but i cant tighten the bolt up anymore without snapping it ???

Great job mate

Still running fine? I finaly replaced all 4 injectors with new one, but first morning start when temperatures are around zero is worse than with the first ones which are done over 350.000kms. Engine shakes on gearbox side, but after a while is all fine. I had an animal (maybe a rat or a cat) which made me a big mess with electrical cables under the bonnet.

Hi, If I was to replace more than one seal would it require a bleed of the system? Or just change seals and put back in? Thanks for the video 👍

How much this ford has driven? Km?

Thanks for video. What is injector order? Close to battery is 4? Then 3,2,1?

Hi mate, great video, just wanted to make sure, the green spray you used was that to prime the injector?

I changed my 4 injectors because jerking motor and fault code with injector around 2000rev/min. You need to find a set without 3 number on the body of injector because it's bad version (for 2nd hand) for new one normally it's work because they change it. Disconnect the battery for at least 15 to 30 minutes. (PCM was update) After installation, you need to have to relearn Knock with Forscan. After start motor and stay 2min with slow engine (normally around 900rev/ min. And 1min at 1200-1500rev/min. After go to drive car for 50km till 200km for learning PCM new values. And if it's not working, change correction factor in Forscan (it exist 3 possibly '4'-'5'-'6'), relearn knock with Forscan. After unplug battery for 15-30min. After start motor normally and wait 2 min at 900rev/min and 1min at 1200-1500rev/min And go for drive.

If I was to take the injectors out of a donor car and put them in mine would I have to code the injectors to my car ?

Verry helpfull video mate ! Can you please tell me whay symptoms did you have for a bad injector ?

Hola buenas qué síntomas tenía el coche gracias el mio falla en el arranque por las mañanas ya tengo puesto todo nuevo calentadores cables de sobrantes ect batería

Hi ya mate brilliant video . Got number 3 injector fail ....how are them numbers from left to right or right to left??

hi, great video. I have hyundai i30 and engine noise is wierd like tractor and rpm is very low on startup but ok upon race alittle bit. Also smells diesel in engine while running , can u suggest anything on that...???

Did u programme it

hi thanks for your video. One question : you have to encode the injector or not ?

Hi what number injector did you do? Mine says its 3rd one dont know which it is can u help thanks

Where did you order the new injector from?? Any part number.

Hi. Did the injector have to be calibrated with the code on the injector body, or was it just a straight swop without the need for calibration? Thanks.

hi nice video have a question u dont need to programing the injector in ecu

From the video, I saw that the old and new injectors are both Continental not Siemens. So neither Siemens nor Continental needs to be coded to the car ECM?

Great work! So i thought that this engine has delphi system...siemens pump and injectors ??

Great video, do the injectors generally come out as easy as that and do they need recoding or is it a straight swap

Hiya, do the injectors correlate to the cylinders, ie cyl 1 is injector 1, etc? Thx

8v ?

Hi friend What year is mondeo? j have focus mk2 1.8 85kw tdci with the same engine j have a problem with injector it d very noise when drive the car ! is the same injector like yours??

Good job very easy to follow cheers😉

Ciekawe jak gniazdo wtrysku jest zanieczyszczone przez smar ropy. Trzeba oczyścić gniazdo wtrysku . Potem można instalować nowy wtrysk. Ja w miejsce świecy żarowej wpuszczam powietrze i frezuje i oczyszczam gniazdo wtrysku. Potem podgrzewania hartuje podkładkę pod wtrysk. Czyszcze wtrysk jeśli zmieniam tylko podkładkę pod wtrysk następnie skręcam całość . I używam zawsze nowej śruby!!!

У меня форд c-max с таким двигателем, если нажать сильно на педаль акселератора то пускает черный дым, едет хорошо, есть предложения? Спасибо.

Thanks a lot!

How can you check which one is gone bad? Thanks

I have exactly the same car. how did you manage to pull the pins from the leakoff pipe(pins that hold the plastic pipe and injector). on mine they face opposite?

Muy buen video correcto, cual el s el par de apriete? Un saludo

what engine oil does this engine like?

Miért kellett cserélni? Nem lett volna elég csak megtakarítani?

Kw?

does it have to be aerated?

How did you code it ?

Молодец ..держи подписку и лайк )!!!

salut tu as oublie de reprogrammer le nouveau injecteur et merci

Didnt see a copper washer ??

сколько стоят?

А прописывать форсунки разве не надо

Ni purge ni rien du tout. Et elle démarre normale !

quisiera saber que ganas engañando a la gente todo mentira desde el primer momento que sacas el clip del sobrante pues sale hacia atras no para delante y terminas el video igual sino programas el inyector nuevo no izistes nada.