Front wheel bearing | Volvo XC70 | Special tool & press |

Подписаться 3,4 тыс.

Просмотров 17 тыс.

50% 1

Front wheel bearing | Volvo XC70 | Special tool & press |
Front wheel bearings started to keep some noise. I ordered a special tool kit from ebay and wheel bearings from Autodoc.
Follow us also:
IG: hans_soolo
FB: Hans's Garage
3 ways you can support this channel:
1. Send this video to a friend who may like it or post it in a motorsport group on social media. Sharing is caring. =)
2. Press like and subscribe.
3. Drop a comment on what you want next video to contain.
CREDITS: "Subscribe Button" by MrNumber112 • Free Download: Subscri...

Авто/Мото

Опубликовано:

24 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 35

@jollyroger2858 6 месяцев назад

Great video, in the past when ive done them its sometimes cost effective to just buy a new knuckle too rather then mess around

@ceesklumper 20 дней назад

I just did this job on my 2002 S80. I just wacked the old hubs/bearings with a heavy hammer and they all came out like that, no press, no special tool needed. Yes I am in countries with snow and salt: Switzerland and The Netherlands and Northern France. I guess the XC70 is different than the S80.

@davidsmall7676 2 года назад

Well done! Persistence goes a long way when dealing with wheel bearings.

@1986jaroslaw Год назад

I did it on my S80 3.2 with the same tool. Very good video and nice work

@SaabAtical2009 2 года назад

the bellows kit must fit. i tried it for my 99er and realised that Saab had a different shape. used an original, cut it and glued it together... worked nice and easy

@davidclarke427 Год назад

Fantastic video great work im researching because mine are currently failing and noisy too

@arthurperez2345 Год назад

Thank you very much you were very helpful

@pavw5508 Год назад

Nice job. I am preparing for similar job. I want to replace the brakes too (calipers, discs and pads. I replaced brakes 3 times already and every time after longer drive on motorway my right wheel would wobble during breaking. I always thought it is to do with the disc. Now I know that it must be the hub bearing.

@hanssgarage1886 Год назад

Thanks. I should also replace pads. In my V70 I had that wobble issue but dics replacement helped. I hope your hub bearing project goes smoothly.👍

@AustinTillison 4 месяца назад

Awesome video! What size tool did you use in your press?

@snowjammma Год назад

when did you put the axle back into the bearing/knuckle

@MynameisEGIS 10 месяцев назад

I have ABS sensor issues and I have noticed you have same sensor what part give speed readings? is it bearing? as sensor is slim and takes reading seemingly from side not the bottom

@ObviousInit1 Год назад

What would you say is an acceptable time to perform this job with a hydraulic press available?

@edbrandt8972 Год назад

Looks like you removed the ABS sensor from the knuckle. Was that required or were you being extra cautious?

@robertasviskupaitis9195 9 месяцев назад

Who makes these bearings for volvo xc70 p3? FAG or SKF?

@christophersterland5526 Год назад

What ton press do you have as I need to buy one

@royman8889 Год назад

The bearing doesn't look fully pressed in as you can still see the outer bearing race protruding out of the hub carrier. Is the metal back collar fouling against the inner race of the bearing when you thought it was fully driven in?

@Pelinas Год назад

I did notes that too, it wasn't press all way in

@lamar9525 Месяц назад

Great YT! What is the tool called?

@argirim8665 10 месяцев назад

Nice job.!! How many tons is your press? I have to do the same job on my xc60. same bearings from what i know of.

@Bumbazaurs 5 месяцев назад

It took me about 8 tonns.

@easy_two Год назад

Having trouble with leveraging down the lower control arm ball joint so it releases. Tried a long pry bar but it only slightly moves up and down inside the compression fitting. Any tips?

@hanssgarage1886 Год назад

I destroyed the CV boot last time.😅 It can be very tricky. I have used also long bar. Sorry, no special tips. More WD40 and longer bar.😉

@easy_two Год назад

@@hanssgarage1886 Thank you for the reply. Actually trying to replace the torn CV boot on the driver front side, which is why I need to get the lower ball joint out so I can then remove the CV shaft. May just have to admit defeat and take it to a shop.

@hanssgarage1886 Год назад

@@easy_two I have also video about CV boot replacement. I used over the joint method this time. But still you have to get the shaft out from the hub.😅

@user-kq9dc6zm9f Год назад

I would have to say this is how not to do it . Certainly made me laugh

@Bumbazaurs 5 месяцев назад

Totally agree, the way he pressed the bearing in the hub, he definetely damaged it a little bit, so the bearings lifetime is shortened, but I saw a tool (a plate like from two pieces) that should be installed on bearing to not damage it.

@masterkang1024 Год назад

Could you put a link to where I can find the tool?

@Dracasethaen Год назад

Not OP, and I realized you posted this 4 months ago, but I believe these are labeled "Gen 2 wheel hub bearing unit tool set for 78/82mm" or some similar wording. Gen 2 and 82mm were the keywords to find the set I needed, and (should) be appropriate for any gen-2 style press in hubs on the P3 platform volvos. Not sure why he struggled with it in this video, but you can pick up a set for $169+. YMMV, I felt it was reasonable to buy at that price since we have two P3 platform volvos I exclusively maintain (Edited for redundancy)