Functional 3D Print Challenge: Can I Print EVERYTHING I Need?

Подписаться 118 тыс.

Просмотров 95 тыс.

50% 1

This video is brought to you by Sovol, makers of the SV07. Check out jle.vi/sovol and use the coupon code NEXTLAYER at checkout to save $10-20 (on orders of $259 or more). They make a great 3D printer that is perfect for beginners, without breaking the bank.
For the last three months, I've been on a mission, challenging myself to use 3D printing to make literally everything I could possibly need for my 3D print farm, makerspace, and recording studio.
In this video, we're going to push consumer 3D printing to its limits by designing, downloading, printing, or otherwise hacking our way towards every solution that I and you could possibly need for your own perfect personalized maker nook.
My goal by the end of this video is to really use 3d printing to finally get my work area organized and under control and hopefully I'll be able to inspire you to do the same.
💬 JOIN MY DISCORD: jle.vi/tnl-discord
🎁 EXCLUSIVE CONTENT ON PATREON: / thenextlayer
🎥 IN THIS VIDEO: 🎥
00:00 Introduction
00:48 Challenge Rules
02:21 Filament Storage
04:21 3D Printer Storage
06:48 Small Stuff & Hardware Organization
09:00 Cable & Electronics Storage
12:28 Drawers
14:01 Storing Bigger Stuff
16:40 Wall Storage & Decoration
19:12 Studio Lighting
21:02 Table Saw
22:03 Acoustic Panels
23:22 Conclusion
🛒 RECOMMENDED GEAR: 🛒
📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing
📍 Complete list of my videography gear: kit.co/jlevi/content-creation
📍 My favorite 3D printing filament: jle.vi/polymaker
📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted)
📍 My favorite BUDGET 3D printer right now: jle.vi/sovol
📍 Check out the official TNL merch: shop.thenextlayer.com/
📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links
🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳
🗿 Collection of all of the models I designed for this video: www.printables.com/@JonathanL...
🗿 RepRack Spool Holder by Repkord on Printables: www.printables.com/model/1290...
🗿 Filler Filament Holder by HugoHuge on Thingiverse: www.thingiverse.com/thing:302...
🗿 Catch-All Trays / Desk Organizer by HD on Printables: www.printables.com/model/3762...
🗿 Borders for Honeycomb Storage Wall by Weazelbuffer on Printables: www.printables.com/model/1662...
🗿 HSW for Bambu X1C or P1P by arod2051 on Printables: www.printables.com/model/4059...
🔗 OTHER LINKS 🔗
👉 My previous video where I talk about the Longer B1 30W and NEJE Max 4 Lasers: • I Tried These 20+ Prod...
👉 My previous video where I shared my Gridfinity tips: • Gridfinity Tips: 3D Pr...
👉 My previous where I talk about my top 3D printed organization systems: • My TOP 3D Printed Orga...
👉 My previous video where I shared one of my favorite functional prints of all time - Cable Winders: • 15 Useful 3D Prints: G...
👉 My previous video where I talked about my top HoneyComb Wall accessories: • Is This 3D Printed Too...
❤️ LOVED THIS VIDEO? ❤️
▶️ Subscribe to the channel
▶️ Watch my other videos: / @thenextlayer
🔔 Turn on Notifications
🎁 Support me on Patreon: / thenextlayer
🎁 Send a “Super Thanks” (Tip)
🛒 Use my affiliate links for your 3D printing or videography needs: kit.co/jlevi
💬 Join My Discord: jle.vi/tnl-discord
✍️ Write a comment below!
👍🏿 Like this video
#3dprinting #3dprinted #3dprinter

Наука

Опубликовано:

1 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 280

@thenextlayer 10 месяцев назад

THANK YOU for watching. Drop me a comment and let me know what you thought of this video!

@garylgoldberg 10 месяцев назад

I like the filament storage if you have the wall space for it. But I'm curious how you handle keeping the filament dry with all those spools just sitting out in the open, unbagged. Do you just dry filament every time you use it?

@Wasser-fz9ub 10 месяцев назад

How are you getting the STL files for gridfinity

@NoamSmadja 10 месяцев назад

KETER has awesome plastic tool drawers stand. its like the metal one you got, just in plastic

@nixquev 10 месяцев назад

Love this! Do another challenge but make a workshop NOT for 3D printing. Something like a kitchen, or a RV/Trailer, a shed. I always feel like 3D-Printing to make more prints is mostly easy to justify but not other spheres of life and I also need to justify it to my wife 😂.

@Mazda.Fit. 4 месяца назад

Did you justify it

@istayhighi1540 10 месяцев назад

I actually make and install acoustic panels for work. We did unbox therapy’s place. Anyway the easiest way to make some is get urself some 8x4 sheets of insulation. Then get a roll of fabric that you like and make sure it’s about 4-5 inches wider then ur 1 inch insulation sheet. Get a can or spray glue and spray the edges and a few inches on the back. Place the insulation sheet face up and roll out ur fabric on top. Start from one side and fold it over the edges. Once u get 2 sides done slightly stretch the fabric over the edges. If you wanna get fancy you can cut the insulation into hex shape with a 3d printed stencil and wrap them after

@thenextlayer 10 месяцев назад

I don't know if I can get that big of stuff here... but I'll check into it thanks

@brianswille 10 месяцев назад

Excellent creativity. I am a Carpenter/Tinkerer and got into 3D printing about 2 years ago. Started designing my own parts and objects about a year ago to solve problems that weren't practical (or feasible) to buy or build out of wood/metal. There are so many things that are just easier and better to design and print than it would have been for me to make out of other materials. I am loving the 3D printed medium and the world it has opened up to me. I have designed about a dozen objects so far and continue to learn everyday. Love your show and it has been an inspiration.

@thenextlayer 10 месяцев назад

Thanks so much for th ekind words!

@lexie2617 10 месяцев назад

Thank you for your content! I got my first printer a couple of weeks ago and your videos inspire me to see how much is possible.

@user-hf9ll3dt3u 7 месяцев назад

This is exactly the type of video I love to watch. I am not going to buy a new printer every year, so I am only medium interested in all the unboxing videos. But I very much enjoy the inspiration from seeing what others do with their printers, the projects they pursue, the problems they fix. Keep on sharing those ideas, it is one of the main reasons why I follow you!

@lesliedickinson 10 месяцев назад

As a stay at home mom I’m finding the storage solution ideas to be so useful! Not heading to ikea sounds like a win! Can’t wait to give the bins and boxes a print

@thenextlayer 10 месяцев назад

I SEE YOU MAMA!

@DXL20 3 месяца назад

Love this going to try and makes some of these I’m new to 3d printing but love it

@YoonSeopKang 10 месяцев назад

I'd love to see you building a window mounted ventilation system for 3d printers. Although there are a few videos about building such systems, they really do not give details about their design choices.

@bnut1576 10 месяцев назад

Another engaging video! I am planning on starting my dive into Gridfinity soon and I have referenced your videos on them lots of times.

@thenextlayer 10 месяцев назад

NIIICE. Get into it :)

@user-dk6ws4oj6r 9 месяцев назад

This is one of the most entertains and informative shows I have seed is some time. Thanks for making it and good luck with your next project.

@thenextlayer 9 месяцев назад

Thanks, you too!

@canuckotter 10 месяцев назад

Minor nit-picking - there are entry-level consumer lathes available that are far more affordable than any laser cutter I've looked at, at least in the woodworking space. I use one to make hardwood pens as well as a few other things... Could make some pretty awesome handles that way. 🙂

@simaddiction 10 месяцев назад

Love the channel. It is very informative along with also being entertaining. Keep up the good work.

@thenextlayer 10 месяцев назад

Thanks, will do!

@matteonicoli 8 месяцев назад

yes thanks for this video! designing and making practical things for me is the thing!

@IshidaEd 9 месяцев назад

Hey Jonathan, talking about your ceiling/wall acoustic panels, the sound deadening effect comes more from the shape of the walls than the material itself. That being said, the way you install your panels shown in the video, with the isolation material hidden inside a flat surface will make less effect than if you had it backwards, with the exposed material attached to a flat background panel. That's why a lot of places just end up using egg boxes or piramid shaped foams, not only because the surface of those materials are porous/rugged, but also because of the pointy shaped design, that breaks/absorbs the sound waves, breaking any possible echo. The honeycomb walls, as well as a gridfinity wall, could do some effect because of the uneven pattern of the surface, that would also break the flat wall surface where any sound wave could travel freely. Thanks a lot for the amazing videos as usual.

@HawkXe 10 месяцев назад

Great video as always! Definitely gave me a few ideas for my own workshop!

@thenextlayer 10 месяцев назад

Great to hear!

@MiKoDIY-lu8qc 10 месяцев назад

A-MA-ZING Job Dude ! You did an amazing job ! And gave me so many ideas :) Thanks !

@thenextlayer 10 месяцев назад

Glad I could help! Grateful for the kind words

@SeanSullivan1958 10 месяцев назад

I hear you on the adapter for the saw and vacuum. I had to design an adapter for a small air pump I use for blowing up all the pool toys. Some of the floats have wierd nozzle sizes so I printed a new adapter that fits perfectly. One of my favorite things about 3D printing. Same went for a mobile scooter we bought for the MIL. Had no hold down for the battery, so I printed one and a knob for the bolt. Lifesaver. Thanks for your vids. I plan on creating a set of bins to organize my desk drawers based on some of your ideas.

@thenextlayer 10 месяцев назад

NICE. Do it :)

@gunslingerc208 10 месяцев назад

Great vid man. Really liking those vase mode storage bins. Going to need to pick up some 1mm nozzles....

@thenextlayer 10 месяцев назад

You should! AliExpress :)

@Marksetter 10 месяцев назад

I would totally love to see a window mounted extractor fan setup, but with the added functionality of being modular, so as to be able to add in extra suction points, such as, solder station, general UVC germicidal, Hepa filter add-in with ozone generation etc...possibilities are endless Love your work and your ideas/visions, i just wish i could afford a not shit 3d printer :(

@thenextlayer 10 месяцев назад

Oh snap that's a great idea

@FAssan-fe3gw 10 месяцев назад

Loved it. Want to see all your ideas. I am in the process of creating my space so got a lot of ideas from this.

@thenextlayer 10 месяцев назад

So glad!

@saffrongames 10 месяцев назад

I would like to thank you for all the content you have made ,I am new to 3d printing and I have been fed up with my ender which I have only had for a month so after watching your videos I finally took the plunge and bought a p1s, I am hoping to use it to learn cad and try to make the cost of my printer back. I am looking forward to it :)

@thenextlayer 10 месяцев назад

Thanks for the kind words, and thanks for supporting the channel! Enjoy the P1S!

@saffrongames 10 месяцев назад

@@thenextlayer I used your new affiliate link I hope it worked well

@timmyreeves4546 10 месяцев назад

I love the idea of making everything yourself it's the coolest thing ever to be able to make so many things yourself. I think it's amazing what your doing with 3d printing and lasers and salvaging things thank you for the content and sharing your ideas👍🤜🤛

@thenextlayer 10 месяцев назад

Thanks for the kind words!

@Schmicky96 10 месяцев назад

The majority of prints that come off a 3D printer are 3D printer parts and upgrades lol

@martinp4591 9 месяцев назад

for the shelfs with the 3d Printers... print brackets to hold a Profile for attaching led Strips. for me sufficent Light makes a lot of tasks arround the 3d printer very important

@asubutler 10 месяцев назад

😊I don’t understand why you are not over 100K. You do very well thought out videos and this series is one I am looking forward to viewing.

@thenextlayer 10 месяцев назад

Thanks! The channel isn’t even a year old. We will get there in 2024!

@nicksmith1415 10 месяцев назад

Love it, plenty of ideas for my dining becoming workshop room. I say room, the other half of the room is my lounge 😁 with space a premium I'll definitely be incorporating some of these ideas. Im new to printing and love the sharing of knowledge that I see across the community. My ambition at the moment is to hone my skills until im ready to make something similar to your moving camera jig/boom masterpiece.

@thenextlayer 10 месяцев назад

Glad to hear it

@travismoore6064 2 месяца назад

Love it, keep these coming!

@erin.anderson 9 месяцев назад

Lots of very cool ideas in here; the vase mode bins make sense, but don't count out other materials or smaller nozzle sizes. Set your line width to larger than the nozzle size some time if you've never tried it. A 0.4 nozzle can easily do 0.6 or even 0.8 width lines for much sturdier vase prints without having to swap out the nozzle at all. Alternately, if you've got a 1.0 nozzle with a high performance hot end, well, go crazy.

@suby7973 10 месяцев назад

I love these toyes of videos! Cant wait to see what you do with the honey comb wall!

@thenextlayer 10 месяцев назад

Thanks! Stay tuned. You're awesome

@deannaatkinson3004 4 месяца назад

I really enjoyed this video. You’ve given me many new ideas for things I need in my small space. I’m finally working on a storage/organizing solution for all of my tools and gadgets. Me? Organized? Say it ain’t so!! Any way. Keep up the great work. Now, back to work designing things to print with the growing collection of filament.

@EZ3DMaker 10 месяцев назад

In a very little space, organization is king, really need to think how I will put all..... thanx 4 sharing

@thenextlayer 10 месяцев назад

Thanks for watching :)

@Ben_EH-Heyeh 8 месяцев назад

The one who developed stack printing the hex wall system...AWESOME, This person took the best and made it better, w00t.

@Enjoymentboy 10 месяцев назад

I've been looking at things very differently since I first started 3d printing back in Dec 2022. I've always been the type of person to look to make something instead of just buying it but often that wasn't really possible. Now however i keep seeing all manner of things I can print instead of ordering online plus I get the added benefit of getting to exercise my creativity which makes the final outcome so much more satisfying. I'm actually shocked at just how much more I can use my 3d printers for than i would have ever thought.

@thenextlayer 10 месяцев назад

I feel you! Same here. So empowering.

@DEtchells 10 месяцев назад

Nice to see BambuLab continuing to support your efforts, props to them! I’m always going for the cheapest filament I can find that’ll actually print well, but have to say that the BambuLab matte PLA is some of the nicest stuff I’ve printed with. If I wasn’t always needing to pinch pennies, I’d print with nothing but that :-)

@thenextlayer 10 месяцев назад

I love it too! It’s really truly great stuff and not having to deal with filling out filament in the system is noice

@DudeRandom21 10 месяцев назад

It's a shame the other build video didn't do so well, i enjoyed it. I do think i like this one better though. The builds of stuff that we probably all need (at least to some degree) is a nice touch. I'd love to see more videos like this. And I'd love to see it happen where you leverage more maker techniques. I'm out here trying to justify building an MPCNC or a laser cutter, give me more reasons haha. Thanks for the video!

@thenextlayer 10 месяцев назад

You got it! This video is doing quite well so I'll do more

@Enpious 4 месяца назад

As a carpenter/woodworker moving into the 3D printing wold, You are dead on about duct tape for dust extraction connectors. But truthfully, you can order 3rd party adapters. These small parts are one of the main reasons I got a 3D printer. As well as for woodworking templates/jigs.

@rbid 10 месяцев назад

The "progress ring" when you have an sponsor announcement is very nice. Hope to see it in the next videos as well :) Greetings from the Galilee .

@thenextlayer 10 месяцев назад

You got it!

@CelticKnotCraftworks 10 месяцев назад

I would love to see the rechargeable bins! I think these are amazing ideas because it inspires other people to organize their space …or me at least😊

@conorstewart2214 10 месяцев назад

Rechargeable?

@juanpablorodriguez6842 10 месяцев назад

I really do like your videos! Thank you for all the inspirations you give me ❤❤

@thenextlayer 10 месяцев назад

Thank you so much!

@SynthaPak 10 месяцев назад

Love workshop build vids, keep ‘em comin!

@thenextlayer 10 месяцев назад

Thanks! Will do!

@Jerradbeckman 3 месяца назад

Dude you blow my mind. EVERY SINGLE VIDEO!

@thenextlayer 3 месяца назад

I’m flattered!!

@Polarzbek 10 месяцев назад

Wow this is killer and definitely gives me some ideas for my own space!

@thenextlayer 10 месяцев назад

awesome, go do it!

@Zeldalovesme 10 месяцев назад

love this type of video, thanks!

@thenextlayer 10 месяцев назад

Glad you enjoyed!

@seanwelding4183 10 месяцев назад

While I love the design of your current acoustic panel on the wall, I highly doubt it will do much of anything since it's primarily wood on the face. If anything it may increase the echo/reverb further since the wood with paint over it is solid, dense, and smooth which will allow sound to bounce right off it. I don't know how well fabric would hold it's shape when laser cut and attached with that design, but using a material like fabric as a face directly over rockwool or fiberglass batt is far superior in terms of performance as an acoustic panel. Also, super small nit pick here, but if you have any fans blowing at or over the exposed insulation, you may end up with some allergy-like reactions from the particles it puts off into the air. P. S. I enjoyed a lot of your suggestions elsewhere in the video, well done video overall!

@TheButchersbLock 10 месяцев назад

A very cool video sir, I have allready printed a heap of Gridfinity so I reckon I will have to tackle the reprack. 👍🇦🇺😊

@thenextlayer 10 месяцев назад

Thank you :) Do it!

@chartle1 10 месяцев назад

21:33 B3D (Before 3d) I would have and did find PVC plumbing fitting and if they were a tad too small I added craft foam. No duct tape

@TechieNI 10 месяцев назад

Yes to all. I love your videos. Your able to keep it interesting.

@thenextlayer 10 месяцев назад

Thank you so much!

@powertechgrows6093 9 месяцев назад

I haven't finished the video yet, but for your filament storage, how do you deal with moisture? All those rolls open to air, do you have a bunch of dryer boxes, or do you dry the whole room? I have 4 rolls in dryer boxes at all times, and the rest in vacuum sealed bags with desiccant. I don't have near what you do, but I aspire to get there one day. Think I need to stop getting filament and get a good quality Bambu Carbon Love your work, thank you!!!

@deepcrows 8 месяцев назад

just want to say I really like your videos, I’ve watched probably dozens of your videos in the past few weeks and I don’t even own a 3D printer!

@thenextlayer 8 месяцев назад

Wow thanks so much. Hope you’ll get into the hobby soon!

@robertzarfas9556 10 месяцев назад

The “let’s get after it” transition felt more natural this time. 👏👏👏. It’s growing on me. Being the Next Layer, maybe, “let’s see what’s next” and then if it makes sense in the context you could add “…on the next layer.”

@thenextlayer 10 месяцев назад

I'll keep at it :)

@courtneydorward-redpandade7624 Месяц назад

Thanks for the video, this one was great. Whats the name of the cable management roller you had there? Keen to use the same :)

@KanielD 10 месяцев назад

For the algorithm

@thenextlayer 10 месяцев назад

As in, you commented for the algo?

@bnut1576 10 месяцев назад

Yep that’s what he means

@ClintonCaraway-CNC 10 месяцев назад

@@thenextlayer I try to comment on all videos I like even if I don't really have anything to ask or anything to say. I've heard it helps the algorithm more than just hitting the like button.

@justina208 10 месяцев назад

Thank you. -The Algorithm

@ljadf 10 месяцев назад

All hail the Algorithm!

@tallgiese1 10 месяцев назад

I like seeing ideas in different places and specifically 3d printed solutions. I like anything dyi

@thenextlayer 10 месяцев назад

Good to know, you've come to the right place

@veselinlazovic3997 День назад

I appreciate the effort, as much as it is exiting to create everything with 3d printing, significant better results can be achieved if all machining technologies are used together (together with all materials) according to to its best use-case scenario. Par example metal inserts for screws have significantly better performance then 3d printed screws. Then instead of printing flexible filaments, making cast form from pla and then casting flexible gives much better result. Of course it’s not possible to cast every form. I find seeking combination of materials and machining technologies give significantly better result than just pure 3d printing. It worth saying that there is sometimes significant investment in tools other than 3d printer. This also has to taken into account.

@SG-sj6cw 10 месяцев назад

By far the best 3dprinter content creator. And you can indeed beat free wood

@thenextlayer 10 месяцев назад

WOW! What high praise :) Thank you

@IkagaraSilvansky 10 месяцев назад

Hey, you should check out making a 3d printed cyclone dust separator as an add-on for your shop vac.

@jasoncy31 Месяц назад

Love this. One of the best videos you've done. And hey, some of us don't mind workshop videos! :)

@lps7695 10 месяцев назад

You made comments on the petg filament, and I see you used the bamboo x1 carbon to print the wall mount. I am having trouble with getting clean prints. Can you give me some pointers?

@LoganMcKay 10 месяцев назад

Hey, can you provide more details on the light stand caster adaptor? I am interested in printing a set for my studio. What hardware did you use and what caster are you using. Did you heat set in a threaded insert, or did your hardware cut their own threads? Also in your design it looks like there should be a second piece for where the thumb screw goes into that tightens into the leg of the stand, am i missing something?

@thenextlayer 10 месяцев назад

All files are shared in Description to OnShape and Printables :)

@RomanBChannel 10 месяцев назад

Answering your comment on connection between the table saw and vacuum - yes, the tape is the solution ) waiting for my 3d printer ti arrive. Cheers, m8

@thenextlayer 10 месяцев назад

Nice. Your life is about to change

@RomanBChannel 10 месяцев назад

@@thenextlayer thanks fort new ideas ;) "to print" list just keeps getting longer....

@TS_Mind_Swept 3 месяца назад

I always find videos like this interesting; not sure about the open air laser thing though.... I believe it was Makers Muse that was fairly unhappy about that whole thing..

@PremixandPedals 6 месяцев назад

I just ordered my first 3D printer, a Creality V3 SE, should be here in a couple of days! I stumbled upon your channel and I love it! I have a question about that hex storage grid you have on your wall. Once you snap the piece into the grid, are they removable? Thank you!!!

@thenextlayer 6 месяцев назад

Yep! They are.

@bmorr 4 месяца назад

This was cool. I want to know more about that filament rack.

@thenextlayer 4 месяца назад

I covered it in my projects for winter video a month or so ago. Check it out.

@vynaltheworld4092 10 месяцев назад

This is a great video format

@thenextlayer 10 месяцев назад

THANK YOU! I appreciate this type of feedback a lot. I said to myself.. "how can I make content out of all the shit I need to do around the studio, but NOT bore people with another 'workshop update' video... Seems to have worked

@alexcostafotografia 2 месяца назад

I really like the stand casters ...do you think I can print that in pla would it hold it?

@oliverphilbrick2986 10 месяцев назад

Banger video. Well done

@thenextlayer 10 месяцев назад

Appreciate it! I wasn't sure how it would do, so I'm glad you liked it :)

@EEEEMMMMKKKK 10 месяцев назад

Fillaments part two and tweaking fillament profiles would be nice. As i look at your prints you need the second too :D

@DavidHyman031 10 месяцев назад

Definitely want more!

@thenextlayer 10 месяцев назад

I can do that!

@xsvforce3335 9 месяцев назад

Great stuff as always. I just wanted to point out that the carbon filled Nylon your using is no where near as strong as machined aluminum because it’s a discontinuous fiber. It might not even be as strong as regular nylon (though it will be stiffer). You need continuous fiber reinforcement to be as strong as aluminum.

@thenextlayer 9 месяцев назад

Good point!

@davidkinn9608 10 месяцев назад

I would like to see a video on the snapmaker J1s. Maybe also a how to with there Luban slicer

@adrianstevenson6281 10 месяцев назад

Great videos. I'd like to how the Sovol SV07 compare to the Bambu Lab x1 Carbon?

@thenextlayer 10 месяцев назад

Toyota vs. Bugatti. One is a reliable economy workhorse, the other is the highest performance and cutting-edge engineering. :)

@JeffreyKretzler 10 месяцев назад

I would like to see some led light decoration that is also functional. My Idea (not that you should) is backlighting the hexagon wall. so the storage is on top of a clear panel surrounded by strips or something.

@thenextlayer 10 месяцев назад

Damn that's a good idea, I wanna do it. Recommendations on LEDS?

@JeffreyKretzler 10 месяцев назад

@@thenextlayer I've had good luck with govee lights, but don't expect accurate colors.

@maximpopusoi8434 10 месяцев назад

The problem with your thermistor is not actually a problem, its a feature of klipper. Its limited to 270 so the abs wont start to melt, and if it goes over it auto emergency stops. You can change it in the config but it becomes risky

@thenextlayer 10 месяцев назад

Seriously? Where in the config do I change? it worked for a while, and then.... nope.

@danyveilleux3864 10 месяцев назад

Clearly, you've done a wonderful job with OnShape. I spent a lot of time on learning Blender where everything is tedious to do; even if CAD Sketcher helps a lot.. Now, I'm wondering if I should switch to OnShape. I will definitely have a look to your large bins but won't buy a 500 x 500 printer for that. :)

@thenextlayer 10 месяцев назад

Did you see my Onshape vs. blender video? ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-gEDRb67-HfQ.html

@danyveilleux3864 10 месяцев назад

@@thenextlayer Yes, but I was not convinced. I like the open source mentality. OnShape is free until it is not anymore or very restricted.

@TimeeJustin Месяц назад

So funny story a couple weeks ago I got a old band saw and a shop vac and I used a little plastic cup and a duct tape to make the connector lol

@dyops 10 месяцев назад

Would putting Eva foam on the tabletop/shelves and printers on them help reduce noise and vibrations? I was thinking of putting one on my drawer table where my future printer would go on and maybe line the edges with it to just in case it may hit the walls.

@thenextlayer 10 месяцев назад

The vibrations are fine b/c these tiles are SO heavy

@dyops 10 месяцев назад

@thenextlayer I have my Ikea drawers which were an extension to my computer desk. Had to cut it since it was a bit long. It will fit a P1S and barely fit a K1 Max ( still deciding which to get). Would the anti vibration feets be enough or a should I go with Eva foam. Tiles may be too heavy for the table. 😅 I may print brackets to secure the table drawer to the wall or at least line the top part with Eva foam just in case it starts hitting the wall.

@djispro4272 10 месяцев назад

Good! But I don’t exactly understand the black HSW boards on a black wall. I would have printed them in the Bambu Lab Orange Matte PLA. I am going to install another SKADIS in my maker nook soon.

@thenextlayer 10 месяцев назад

I need to make sure it's not too visually intense for filming, hence the black on black. Stay tuned, future videos will show it done

@logicalfundy 10 месяцев назад

It can be a subjective thing - personally, I don't like making my work space stand out too much; I would have not used any orange at all, unless it was something I really wanted to highlight. Although I'd probably do something a bit off-black to not make it completely invisible.

@djispro4272 10 месяцев назад

@@thenextlayerOh okay. I guess the accessories on the wall could have a bit more color.

@tylerjustuspaige 10 месяцев назад

What shelves do you use for your 3d printers? What company makes them?

@thenextlayer 10 месяцев назад

These ones: grimaitalia.it/portfolio_page/maciste/ I'm not sure they're the best but they're the most affordable ones in Israel

@Jai.zTechDomain 3 месяца назад

Awesome!

@arowe231 10 месяцев назад

Cool video with a lot of good ideas. As for your wall I'm not sure?? Cool gadgets?

@thenextlayer 10 месяцев назад

Thanks :) And yeah, I guess I'll do that

@talmeirav3862 9 месяцев назад

אלוף! סרטון מעולה!!

@danielbern7385 10 месяцев назад

Great video, I enjoy your channel! I’m new to 3D printing, just got me a bambu X1C and I’m also in Israel. Wanted to know how you ship from Bambu to Israel?

@thenextlayer 10 месяцев назад

They ship stuff directly to me for review :)

@danielbern7385 10 месяцев назад

Kinda knew this was the case… but had some hope there was another way. Thanks anyway, keep up the good work with your videos!

@kennybrooks4570 10 месяцев назад

18:28 Anyone know to get this to work? I made one with .2mm spacing and when I go to slice it, it is covered support material

@ccnuygaming 10 месяцев назад

brother i need help pls i have an ender 3 i cant print a cover for my screen cus it gives up at the 2nd layer pls

@ArcAiN6 10 месяцев назад

table saw, and router / router tables ARE professional tools

@pierrelandry4742 8 месяцев назад

Great Video.

@printingthepokedex2636 10 месяцев назад

I recently got a sovol sv07 and was wondering if you could point me at a help forum for getting it working with orca slicer? I keep playing whackamole with gcode config and find the documentation to be nonexistant

@thenextlayer 10 месяцев назад

If you message me on Discord I'll send you my config files. It's on my Patreon too

@thenewmodelworkshop5743 10 месяцев назад

For the bins, why not get one of the PET bottle to Filament machines and recycle your materials

@thenextlayer 10 месяцев назад

Hmmmm not a bad idea

@EEEEMMMMKKKK 10 месяцев назад

@8:27 yes!!!

@netpackrat 10 месяцев назад

Not sure why you consider a lathe or mill outside of the rules of a maker challenge. You can get into a reasonably sized benchtop lathe for about what you would spend building a Voron 2.4 or Trident.

@thenextlayer 10 месяцев назад

Really? I always thought a lathe was like... only for pretty serious workshops? No idea where I could get one in Israel though.

@BlueProgram 10 месяцев назад

I really enjoyed this video. And I would love to see more. But maybe next time not as one long video but as a series of videos to some certain topic. Like: Organize your drawers journey Part 1: integrate old organization into new ones" I am not sure what is more interesting for people to see. If you want to seee every solution that you have then one vug video is probably perfectly fine. But if someone is only interested in some specific topic then splitting up one topic in more videos will work out best for those viewers. Also you can probably generate more clicks on that which is good for you. And people looking for some specific idea will find you more easily through searching

@jasondraper5942 10 месяцев назад

Those spool shelves look amazing, are there any concerns with keeping the filament exposed? I’m new to printing but there seem to be a lot of solutions for keeping spools in dry boxes. This led me to believe that storing opened filament without desiccant would be bad idea. Am I concerned about nothing?

@PleakeCrions 10 месяцев назад

There are certain filaments that are hygroscopic, which means they will pull moisture from the air and it will make printing with them a pain until they’re dry again, but PLA is very minimally hygroscopic, so it can be left out for years without becoming wet enough to notice. So no you are not wrong to be concerned, you just need to know which filaments need dry boxes and which don’t. Most of the higher end/engineering filaments are typically the ones that need dry boxes, such as PETG, TPU, Nylon, etc. but PLA is fine without one and PLA is what most people start printing with

@SlurmDude 10 месяцев назад

Yes and no. If you plan to have 30 rolls open, you do need to worry about. But if youre a one roll at a time man, in general, no, you dont really have to worry about it, as long as you can use up a roll in about 6 months. However, youtubers hoard filaments, so at that point its just easier to make a humidity controlled room, rather than have 70 dry boxes

@coolcoolercoolest212 10 месяцев назад

I was wondering this as well. Maybe the whole space is climate controlled.

@PleakeCrions 10 месяцев назад

@@coolcoolercoolest212 yeah I meant to say something like that in my comment. I think he’s in a basement and most people who have these big printer spaces make sure to have dehumidifiers running all the time to keep the humidity to a minimum

@thenextlayer 10 месяцев назад

Unfortunately you're 100% right. Most of the filament is PLA, but you'll notice I have some stuff in bags (PETG, Nylons)... however, bags aren't as good. Right now, I'm bagging some of it, the rest, I'm drying before I use. It's just too humid here to run a dehumidifier 24/7, it would cost me a FORTUNE... so I just dehydrate filament as needed overnight

@charlie3074 4 месяца назад

how about use wall mounts as a mini shelf for printer shelfs

@JoeC-tt9oq 10 месяцев назад

Wanna see that 500mm!!! I think its the sweet spot for sizing.

@thenextlayer 10 месяцев назад

It's pretty insane. Having difficulty getting it printing nicely though with a 1.2

@m97120 8 месяцев назад

How did you come to the conclusion that the Ikea pegboards use more plastic than the hex wall? The hex wall is entirely out of plastic and the Ikea pegboards are made out of fiber board (wood). Plus, the Ikea system allows you to use very minimalist mounting solutions that use less plastic than a single hex wall hexagon.

@thenextlayer 8 месяцев назад

I was mistaken

@ying9347 9 месяцев назад

Can I print it with resin printer?

@oneredpanda9933 10 месяцев назад

love it

@misty7220 8 месяцев назад

I'd love to see 3d prints on the backboard

@georgskleinewerkstatt8678 10 месяцев назад

U R greate keep on going

@thenextlayer 10 месяцев назад

Thank you, I will

@cardinalcraze8497 10 месяцев назад

Can you do a video showing different 3D prints that you use in your daily life outside of the print-farm? I think it would be more entertaining for the average 3D print user who looks for more home applications like myself. Just a suggestion

@thenextlayer 10 месяцев назад

YES This is actually already on my list