FX AMP Regulator rebuild UK spec 

thank you for watching 😀

really glad they are useful 👍😀

it was nice to talk to you 😀

thank you 👍

Nice one👍 they do make life a bit easer

No problem mate. Good Luck 👍

Glad you liked it, thanks for watching 👍

Thanks (you give yourself too little credit), I am not too worried though, I would rather the information be out there, and if it helps someone out then why not. Thanks for watching. 👍

Thanks, much appreciated. 👍

i am glad it helped😀 you situation is why we started doing these vids in the first place so it's great that they are working 😀

@@sub12airgunners 100 percent buddy thanks again because without you’re video I wouldn’t have tackled it 👍

Thanks for watching. 👍

Good to hear, even if you don't have an impact all the info should be somewhat transferable to other rifles, theres not much difference in how they operate, but good to know you enjoyed it.

Glad you liked it!

where can I get the brass piston from please

Thanks!

Glad it was helpful!

hi yes nice to meet you to it's an ergo chubby grip from air gun 101 shop👍 i would not use autosol unless you can make very sure you can clean all the residue when your finished 😀

Thanks for that.@@sub12airgunners

My Maverick came through at about 10.8 lb/ft, and I don't think there is anything wrong, it may just be the importer setting the power on the low side to be safe. Your RFD should be able to sort it though, the hammer spring just needs adjusting up a little. But let us know what happens. Thanks for watching.

Andy, Which pellets did you use to test the ft lbs?

I made this one but I don't sell them, they don't really give any upgrade over the standard delrin piston. Thanks for watching.

@@sub12airgunners Good afternoon. Do you have a video about how you made such a piston with derlin?

()()()()()( is the normal stack with the final washer facing up towards the brass reg body. Thanks for watching

Hi, Its type 2 anodizing with red dye and I did it myself, the rifle needs to be fully gutted and to be honest its a pain to do. look up anodizing on RU-vid and you will get an idea of whats involved. Thanks for watching. 👍

@@sub12airgunners Thank you for reply will do

Glad you liked it

FAC bellevilles are between 0.5 and 0.6mm thick, for sub 12 you don't want the FAC bellevilles in the reg it just makes it much harder to get the reg pressure low enough, and you have very little adjust ability below 100bar. Thanks for watching

the bottle he displayed is sold from TW Chambers £5.56 CN002 Molybdenum Disulphide Powder

Hi Andy, yeah no problem, been having a little fiddle with the maverick so ill post a vid in the next couple of days. Thanks for watching. 👍

try sub 12 airgunners that should bring it up 👍

Thank you now bought and paid for.

Hi, I made it all, Bagnall and Kirkwood sell one of my cocking handles if you interested look on their site for A14 extended cocking lever. The other stuff was made over the time just for a bit of fun.

If you try it with 10.34 you will find you will be around the 11 ftlb mark 👍

@@jeffhello1444 thanks Jeff it may be on its way to sportsman gun centre to have a look at... however when it comes back I will try 10.34... many thanks

Jeff is spot on, hence my question regards the pellets. I was getting 10.8 ft lbs with AADF and JSB when the gun arrived. With the 10.34 heavies it was putting out 11.3. I've tweaked the hammer spring adjuster slightly now and get 11.6 ft lbs with the heavies, and 11.2 with any 8.44 pellet. The shot to shot consistency with the heavies is better in my rifle. Shot a 10 shot string this morning with spread of 4 fps and std dev of 1.2. Thought that was a fluke so tried again and got exactly the same result. I find with the 8.44 there is a little more spread, although that is still only 9 fps with a std dev of 3, so still amazing. The other thing is you need to shoot probably 150 shots through the rifle before testing. The regulators need some time to bed in. I've put more than a tin through mine now and it is amazing. Enjoy it when you get it back.

@@grantbennett9879 thanks grant it’s probably me worrying over something which may be something not to worry about... I was probably expecting it to be at least 11.6 out of the box and when the chronograph said 10.5/6 it got me thinking for a rifle of this much money it should be 11.6 out the box.. anyway we’ll see what happens I myself don’t want to adjust anything in case I bugger it up just don’t have the guts lol.

@@andydowden8117 Yes 11.6 out of the box is a tricky one, lots of people use 8.44 if you set a rifle to 11.6 with 8.44 it will be over the 12 with 10.34 and if you set it to 11.6 with 10.34 it the seems low with 8.44 so it is bit tricky for the RFD, it's the stupid law

The reg sounds like its creeping, it the top of the piston damaged? a small amount of creep is normal (1-2 bar)but 10 bar sounds excessive, also are you sure its not the gauge settling down, some of the analog gauges take time to settle down and start reading correctly. Thanks for watching.

Hi not sure on the RAL number they are anodized, not painted I believe, so getting a color match may be a bit difficult, you may be able to have it matched by a paint shop though. But I have no idea on the RAL number sorry. Thanks for watching.

Hi, the belleville washers (commonly known as spring washers) act as the spring they are the small grey discs seen at 24:04 . Thanks for watching.

Hi, its just a copy of the original Delrin piston in brass with a small Delrin plug pressed in the end. The holes are the same size and it was made on my lathe and mill. Thanks for watching. 👍

@@sub12airgunners I’m just interested how you made the hole through the Delrin seat into the centre of the piston, did you drill a 45 deg hole etc

we have been making and selling them for a few years now have a look on ebay 👍

Yep a couple more on Ebay now. Thanks for watching 👍

Hi, A couple of people have asked for the tools so what ill do is make a few and stick them on Ebay. ill post the link here when they are ready so keep an eye out. Thanks for watching. 👍

Hi yeah I sell them on eBay, with a set of the reg O rings. link below. www.ebay.co.uk/itm/373613551298?hash=item56fd1a5ec2:g:J5EAAOSwNwpgWKA7

@@sub12airgunners thank you very much unfortunately they are for sale only in UK, and they don’t ship them to USA . Can sell me one?

hi no sorry we don't work on peoples guns

Thanks, yep brass pistons starting to come through now, try with the standard stack first, the thicker belvilles only allow you to get higher reg pressures you may be able to leave off the 11th one and use 10 it will give you a finer adjustment at our reg pressures. Thanks for watching

@@sub12airgunners thanks 😊 for the info

Thanks, but we can't work on other peoples rifles unfortunately, we don't have an RFD licence so we can't take rifles in. Thanks for watching though and its not as hard as it looks. Thanks for watching.

I sell them on eBay, link below. Thanks for watching. www.ebay.co.uk/itm/373613551298?hash=item56fd1a5ec2:g:J5EAAOSwNwpgWKA7

There is some on ebay at the moment

Hi I made another couple for Ebay, but they are selling faster then I can make them at the moment, one left though; www.ebay.co.uk/itm/FX-Impact-Crown-AMP-REG-O-RING-KIT-WITH-TOOLS/373512063114?hash=item56f70dc88a:g:J5EAAOSwNwpgWKA7

Similar it's moly lube 👍

Hi, A couple of people have asked for the tools so what ill do is make a few and stick them on ebay. ill post the link here when they are ready so keep an eye out. Thanks for watching. 👍

👍

They are a bit hit and miss, some gauges are very accurate and some are way off, I put Wiki gauges on this rifle just so I was confident what pressures I had in the rifle. Thanks for watching.

John what did you mean if it drops off the reg it might spike.!

@@andydowden8117 if you shoot it down to 60 bar the power might rise up wards if the hammer spring is set up wrong, try it if it does it just needs the hammer spring backing off a little bit

Hi John thanks for that tip but I would never take it down to 60 bar that’s just me but thanks a lot.

@@andydowden8117 ok

Hi, thanks for watching.

Hi I made it, but I don't sell them unfortunately. Thanks for watching.

every day is a school day for us, but have picked up a fair bit over the years 😀