Тёмный

GM HOLDEN 308 V8 Build Part 1 (Pistons and Main caps) 

MS Engine Reconditioning
Подписаться 18 тыс.
Просмотров 21 тыс.
50% 1

Part 1 of 4 Mick from 'MS Engine Reconditioning' building my 308 Holden V8 motor.
If you would like to follow us on facebook see below!
/ msenginereconditioners

Авто/Мото

Опубликовано:

 

30 апр 2020

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 19   
@change_your_oil_regularly4287
@change_your_oil_regularly4287 2 года назад
Thanks for the uploads 👍 Though it would be good if the camera man filmed in landscape not portrait mode
@bigblockpop
@bigblockpop 5 месяцев назад
Love your videos Mick
@anthonygeha5362
@anthonygeha5362 10 месяцев назад
The accumulator groove provides additional volume below the top ring so pressure doesn’t build up and attempt to unseat the top ring.
@johnbowen2963
@johnbowen2963 3 года назад
YA BANG ON MATE WITH THE CONRODS BOLTS . .
@grantreid8583
@grantreid8583 2 года назад
You forgot to check the thrust clearance on the crank it's always nice to know that it is within tolerance.
@shaneanderson1036
@shaneanderson1036 2 года назад
do you drill out the block inside the oil pump mount to allow greater oil flow through the block ??
@samscreativefarm
@samscreativefarm 3 года назад
Good bloke👍
@lobsterwhisperer7932
@lobsterwhisperer7932 3 года назад
nice engine malaka
@loosemouthcowboy4790
@loosemouthcowboy4790 Месяц назад
Great video but please do a wide video instead.. it's too small to see anything
@ritchieb5146
@ritchieb5146 Год назад
Hey Mick do you know the build codes for those blocks by any chance?
@dezza718
@dezza718 2 года назад
Old tech
@markm4603
@markm4603 Год назад
Pushrod engines are so good
@dezza718
@dezza718 Год назад
@@markm4603 like steam engines
@Hardtarget87jcvd
@Hardtarget87jcvd 7 месяцев назад
Yes, for an old car. Fool.
@dezza718
@dezza718 7 месяцев назад
@@Hardtarget87jcvd shit technology
@ChumpyChicken2
@ChumpyChicken2 Год назад
Filmed with a potato
Далее
GM HOLDEN 308 V8 Build Part 3 (Heads and Pushrods)
11:31
Выпускаем трек? #iribaby
00:14
Просмотров 392 тыс.
4.2L Engine tear down (Holden 253)
1:13:03
Просмотров 2 тыс.
Cost of the Holden 308 Rebuild for My HZ One Tonner
27:57
Holden VR 304 Injected Engine into 355 Stroker
14:33
Просмотров 25 тыс.
GM HOLDEN 304 V8 ENGINE RE-BUILD [EP1]
28:37
Просмотров 316 тыс.
Holden V8 Rear Main Seal Installation.mp4
11:53
Просмотров 144 тыс.
EPISODE 69 - HOLDEN 355 STROKER DYNO RUN CARNAGE!
35:04
Holden 253 Build  ACL High Comp
8:58
Просмотров 40 тыс.
TD42 Bottom End Build Part 1
10:20
Просмотров 10 тыс.
Holden 304 hydraulic roller retro fit
7:12
Просмотров 32 тыс.
T55 Narxi 23 900$ 📞95 155 03 00 | 📞91 033 03 03
0:18