No video :(

Harbor Freight Tire Changer Mods, to the new black version on the cheap with scrap I had around

Подписаться 3 тыс.

Просмотров 28 тыс.

50% 1

Ok everyone, I bought the new black harbor freight manual tire changer and did my front tires on my 1970 Dodge Dart Swinger the rims were 3 1/2" wide and tire size was 165/80 15, was a little more difficult that a 7 or 8" wide rim but I was happy how well it went. Will be using it more on future projects.
Duckbill option #1: amzn.to/3sHF5sx
Duckbill Option #2: amzn.to/3SsvAYX
Centering cone Option #1: amzn.to/3TpV8qg
Centering code Option #2: amzn.to/3SqUMPA
Larger cone option: amzn.to/473wyPl
I did anchor it to the floor, here are the anchors and the bit I purchased to drill in the concrete.
Anchors: amzn.to/3Qh8kKK
Concrete bit: amzn.to/3FvtQGZ
Clamps for holding the tire down in the center of the rim:
Option #1: amzn.to/3Mskxv2
Option #2: amzn.to/3Mskxv2
Lastly a tire iron if you want (I did buy one of these as well):
Option #1: amzn.to/40pa0qh
Option #2: amzn.to/3SqpJU8
Warning
This video is made for entertainment purposes and not necessarily educational. it doesn’t mean to hurt any…and don’t take it seriously. I enjoy doing this, do what I do as your own risk.
Disclaimer
As an Amazon Associate I earn from qualifying purchases, I purchase all the products on my own or provide a link to a similar product I use. I do not get any freebies, I purchase everything just like you do.
The information on this RU-vid Channel is not intended or implied to be a substitute for Professional advice. All content including text, graphics, images, and information contained on or available through this channel is for general information purposes only.
This channel makes no representation and assumes no liability for the accuracy of information on or available through this channel, and such information is subject to change without notice.
You are encouraged to confirm any information obtained from or through this channel with other sources and review all information regarding anything shared in the videos

Опубликовано:

29 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 47

@javybeaz3236 7 месяцев назад

I made mine over 4 years ago. I use it all the time. Use a longer bar, make a stronger base for it it won't wobble. I upgraded mine. it works a lot better

@ShopDogFabrication 7 месяцев назад

I have it bolted down to the floor now. Way easier, I also drilled a couple holes so I can hold the rim down better. I’ll try the longer bar for a bit more leverage.

@MoiDj22 2 месяца назад

I got the tools for the same reason as you, tire shops didn't have the time, I work all day, don't get too many days off. Great mods, some day I might try to do something similar to it. Thanks for your video.

@ShopDogFabrication 2 месяца назад

Appreciate you taking the time to watch and commenting!! It makes it easier to change a tire.

@73dcp 11 месяцев назад

I just got one of these changers and decided to bolt it directly to the concrete floor using only the square flange at the bottom of the main tube. I drilled out the original holes for 1/2" bolts and used flush drop-in anchors so I can remove the unit for storage. This thing is super rigid attached this way, and I don't have any problems at all breaking beads with the wheels flat on the floor. A towel can be laid down to protect sensitive rims. I really don't get what those crisscross c-channel parts are for that they provide to bolt this down with. They seem to make the unit less rigid in the long run. I am definitely going to built the duck head mod!

@ShopDogFabrication 11 месяцев назад

I defiantly need to bolt it down. They only had 3/8” drop in anchors at a store near me so I went the plywood route in a pinch. Want to bolt it down and make it removable. Good to know 1/2” anchors make it plants rigid.

@bryans8193 11 месяцев назад

73dcp what length bolts did you use to secure it to the concrete?

@73dcp 11 месяцев назад

@@bryans8193 I think 1-1/2"

@lar4305 7 месяцев назад

I built the mod duckbill for mine and bolted it down so i can remove it and reinstall it when i need it. It worked great, i did both my cars and a jeep with 16" AT tires with no problems.

@smoke05s 9 дней назад

I agree, the crisscross c channels make it harder to use. Just put a 2 x 4 under the tire /rim and make sure the breaker arm is completely vertical. Also it needs to rub the rim to work. Try it, boom works the first time almost every time. To mount the changer to the floor I just used those blue masonry anchor screws from Home depot just on the base (the size that fits in there maybe 1/4" nothing big. . .and I have leaned on it hard for about 6 years now. Its rigid. Works on Motorcycle tires and car tires really well. I will make one of these one day (with square tubing).

@saberconstruction7224 11 месяцев назад

For your round insert. Instead of 2 set bolts use one on the corner. It will hold the round stock tighter one the square tube.

@ShopDogFabrication 11 месяцев назад

Thanks for the tip, I have a couple more tires to remove, I’ll give it a try.

@madgingercustoms 10 месяцев назад

I like the improvements that were made from the red one we have! Great video!

@ShopDogFabrication 9 месяцев назад

Thanks so much! Appreciate you taking the time and providing feedback.

@BDOML9101 7 месяцев назад

The only improvements I saw were the rubber coverings...Which u can add to the red one yourself as I did.. Changing the rod that goes through the lug hole to hold the wheel from spinning to a drop in bolt/rod is actually a down grade from the red unit...

@madgingercustoms 7 месяцев назад

@@BDOML9101 the red pin is garbage and the first thing to bend. I drilled mine out to accept a bolt. You may have seen that in my video.

@ShopDogFabrication 7 месяцев назад

That pin is a waste like you said. I pretty much drilled gm / ford / mopar bolt pattern in mine for a least 2 bolts to hold the rim in place.

@1925sk 7 месяцев назад

Might try using the other end of the bar with the hook so it doesn’t keep slipping off.

@wicapri82 11 месяцев назад

May be a good idea to have a dedicated pry bar that has the sharp corners rounded off to avoid damaging the tire.

@ShopDogFabrication 11 месяцев назад

That the plan, make it a spoon shape or buy and actual tire iron, what I had to use in a pinch.

@mytube71 4 месяца назад

You have to fixing the ground Plate from the Harbor Freight Tire Changer on your Garage-ground with Bolds!

@ShopDogFabrication 4 месяца назад

I did, I just didn’t have them at the time of the video.

@donkeydiehard879 11 месяцев назад

Leave a tiny bit of air in the tire and use bead lube/soapy water. Even if you let the air out and just put the valve back in so air can escape as easy while pressing on the bead. Bead breaks much easier that way.

@ShopDogFabrication 11 месяцев назад

Thanks for the tip!! Really appreciate, I have 3 tires I need to bust off. Will defiantly give it a whirl.

@cheetahpro 7 месяцев назад

@6:10 in the video you are just pushing on the tire side wall. Pull the tire/rim towards you about 4-5 inches. One should pull the tire/rim away from the bead breaker slightly on a angle in order for it to push against the underside of the bead/ rim when one is pushing down. It shouldn't just push on the tire side wall but directly on the bead and rim while pushing down on the bar.@ShopDogFabrication

@dimitriostambakis9461 3 месяца назад

Could you please give us the actual length, ID and OD size of the main tube which goes over the HB one? And also the length and thickness of the round tubes? Thank you, this was a very nice and simple to understand video!

@ShopDogFabrication 3 месяца назад

Sorry just got back from a trip, the od of the harbor freight tube is 2.05” roughly and my id is just a hair over 2” and 12 1/2” in height. I would use square tubing for the arm around 1 1/2” or 1 1/4” and the size below it to fit inside.

@mtraven23 9 месяцев назад

I think you'd be better off grinding a flat in your round tube so those screws are pressing a plane against a plane, instead of a plane against a line (tangent the circle)

@ShopDogFabrication 9 месяцев назад

That’s a good suggestion, I’ll have to see what I can do.

@robertwhitejr.1316 6 месяцев назад

I just did a set of 33s this would of made it easier for sure. But the rubber pad you say to set your wheel on i put on top of the wheel instead of taping the not so centering piece

@robertwhitejr.1316 6 месяцев назад

I put mine on a heavy duty pallet and use the forks on my tracktor so i can use it anywhere

@ShopDogFabrication 6 месяцев назад

Good to know I can do 33 no problem, I have 31s now on my truck. So when the time comes it can be done.

@jeffallen3382 2 месяца назад

It would also work better when putting the tire back on if you use a lubricant...

@ShopDogFabrication 2 месяца назад

Agreed, I think I used simple green at the time. Something better would help for the next go round.

@tonyp9609 6 месяцев назад

A company makes it. Lucid

@METALTOTHEPEDALx1M 2 месяца назад

are 315s too big for these harbor freight tire machines?

@ShopDogFabrication 2 месяца назад

I had a guy tell me he’s done 35 inch truck tires on them. I’ve done a 275 before.

@johnysilver1853 8 месяцев назад

Is it for only tire removal or installation as well and which duckhead better of those 2 in description?

@ShopDogFabrication 8 месяцев назад

They are both the same by 2 different sellers, I list both of them in case one is not in stock. You use the same one to mount and dismount the tires.

@user-fy5bn9jm3y 3 месяца назад

U country name sir..Rate pls

@joshuamcneal5515 8 месяцев назад

Can I please pay you to build me the add on, I have the same black tire machine

@ShopDogFabrication 8 месяцев назад

There are several people that sell them on eBay. Different levels or kits.

@CelataForCongress 6 месяцев назад

is it just me or does everything from Harbor Freight need to be modified....

@ShopDogFabrication 6 месяцев назад

Not sure about everything, but this mod makes sense. I think it made changing a tire a whole lot easier. The blast cabinet mods I did helped a bunch as well. Now that I think of it, I guess I have modded a couple of things. Lol

@kirkblee5853 3 месяца назад

It's easier, and less harmful to rims and tires, just to use a couple of spoons and some good lube to remove and install tires on any rim. Duckbills and other rotating levers are only faster/easier when powered by a machine with gobs of torque and anchored to a concrete shop floor.

@ShopDogFabrication 3 месяца назад

I have a spoon now and it’s bolted to the floor. When I shot the video didn’t have anchors to bolt it down. Works pretty slick when I need it.