Harley Davidson Clutch Cable Assembly Side Transmission Cover-Remove DIY

Подписаться 217 тыс.

Просмотров 43 тыс.

50% 1

In this free DIY video we show you how to remove your Harley side transmission cover and an easy way to disconnect & then replace your Harley clutch cable inside. Make sure you have a new side cover gasket ready to go and some oil/fluid to replace what you loose when removing the side transmission cover. There is also a small rubber o-ring you might want to have on hand to replace where the clutch cable enters the side cover. It tends to get damaged during removal/install. It can be re-used if it looks like it's in good condition.
Video of Interest:
(You may have to remove the entire assembly & we've got you covered)
GET THAT VIDEO HERE: www.lawabiding...
GET OUR HARLEY HANDLEBAR INSTALL VIDEOS HERE: www.lawabidingb...
GET OUR OTHER HELPFUL FOR PURCHASE VIDEOS HERE: www.lawabidingb...
VISIT OUR STORE HERE:
shop.lawabidin...
BECOME A PATRON MEMBER AND GET EXCLUSIVE ACCESS: / scrappy
LEAVE A FLAT DONATION: www.lawabidingb...
2014 & newer Harley Davidson's have hydraulic clutches, so this side transmission cover is just for looks and you'll lose no oil when removing it. There is just a bleeder valve for the hydraulic clutch line hidden behind it.
This particular segment of video is taken directly from our #1 ranked Harley Handlebar install series of videos. If you think this free video of ours is detailed, you really need to see our premium videos! We have you completely covered, regardless of what type or height of handlebars you want to install on your Harley. Trust us, there is no need to take your Harley to a dealership and pay $1,000 to $2,0oo to have them do this for you. You can do it right in your shop or garage, right on the kickstand, and no specialty tools are required.
Bikers around the world are installing the handlebars of their dreams themselves right now on their Harley's while watching our tutorial videos. Have the pure satisfaction of wrenching on your own Harley!
GET OUR HARLEY HANDLEBAR INSTALL VIDEOS HERE: www.lawabidingb...

Опубликовано:

7 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 17

@CarlosGarcia-ls4hn 11 месяцев назад

Do you have to make sure that the outer ramp is positioned to the left, where the cable is not pulling on it, so that it basically is in the position where the handle bar lever is not in the pull position?

@colmcillian6782 3 года назад

Video was really handy this morning when my cable broke going through Dallas this morning. I gotta say though this is an asinine way to run something that breaks so often. Why would they think its a good idea to put a cable INSIDE the damned casing. I bought the road king because it had bigger bags than anything the BMW dealer could offer when my Victor finally got to worn down, but if this is how they design things I wont be getting another. This is a fairly common point of failure, it should be something easy to replace on the road side with a pair of pliers or two. It should not take half my tool roll and bumming a ride to the hardware store, because who cares a spare bottle of fluid.....

@jerridabblett2082 5 лет назад

Torque specs would be great on a informational video thanks

@chrispybattyone5937 3 года назад

132-165 inch pounds

@TsRide83 5 лет назад

Just to ask what if you didn't rub some of that oil on the gasket would it still be ok?

@ElijahMendiola 5 месяцев назад

i accidently put motor oil !!! is it ok or do i need to take it back off and replace it ?

@rogerantle578 3 года назад

Can you post a video and description of what all to check if you suddenly lose all clutch? 09 Night Train and clutch lever just suddenly went to the bars with slack in it, no clutch cable pressure at all

@charlesmckenzie5250 Год назад

I am glad to see H-D decided to use snap ring to hold clutch actuator in place. Finally! Had sportster years ago. Took cover off, saw it was held in by punching and swelling lip. Didn’t even put back together. So disgusted I practically gave it away. Absolute junk workmanship

@peterchojnacki5111 4 года назад

I have oil coming out of the clutch cable at the adjustment bolt that's covered by the weather boot. Any thoughts as to how the oil is getting in there?

@iGigaCow 3 года назад

I just recently replaced my clutch cable on 05 road king. During install I was able to adjust play of the cable pretty substantially, but after a couple rides it’s tightened up and even the loosest adjustment on the cable is like *justttt right. Any ideas?

@vikingraider1 6 лет назад

How much transmission fluid did you need to put back in?

@RyanUrlacher 6 лет назад

We suggest you check the manual for your bike. Usually a quart. Ride safe & Ride Often! Here is a link to a bunch of our useful Free vids: www.lawabidingbiker.com/freevideos Here is a link to some of our useful for purchase videos: www.lawabidingbiker.com/buyvideos Want Answers & Information Fast? And help support us at the same time? Do you like the content we provide? Our patrons get answers to their questions/comments/feedback in less than 24 hrs and are part of our Private Facebook Group. If you are interested in being in this exclusive group you can get all the details at ==> www.lawabidingbiker.com/patreon If you haven't subscribed to the Law Abiding Biker Podcast make sure to do so. Listen in as we talk weekly about issues/items like this & so much more. You can listen on iTunes (Apple/IOS), Stitcher Radio (Android), or any other Podcast App ==> www.lawabidingbiker.com/podcast Join our free email club at /www.LawAbidingBiker.com/EmailClub. Only relevant content will be sent from time to time. Email club members are the first to find out about free or for sale content are given special coupon codes.

@vikingraider1 6 лет назад

Thanks pal!

@chrispaquette3868 5 лет назад

Replaced drive belt on 97 fatboy, put everything back together, got to adjusting the clutch and I can't seem to get enough tension on clutch cable, also noticed the clutch hub adjuster screw doesn't feal like it's touching when I are it in before I back it out the half to full turn out. Any ideas?

@diablo-km2ot 3 года назад

my oil slinger is missing just the rod is expose but can not pull out to repair 0:37 so I dont have no clutch can you help

@spudd222333 5 лет назад

My clutch cable even fully loosened is too tight I installed 14 inch t bars and bought a 14 inch burly kit I don't know what im doing wrong can someone help me please

@RyanUrlacher 5 лет назад

Sounds like the cable may not be long enough. Ride safe & Ride Often! Here is a link to a bunch of our useful Free vids: www.lawabidingbiker.com/freevideos Here is a link to some of our useful for purchase videos: www.lawabidingbiker.com/buyvideos Want Answers & Information Fast? And help support us at the same time? Do you like the content we provide? Our patrons get answers to their questions/comments/feedback in less than 24 hrs and are part of our Private Facebook Group. If you are interested in being in this exclusive group you can get all the details at ==> www.lawabidingbiker.com/patreon If you haven't subscribed to the Law Abiding Biker Podcast make sure to do so. Listen in as we talk weekly about issues/items like this & so much more. You can listen on iTunes (Apple/IOS), Stitcher Radio (Android), or any other Podcast App ==> www.lawabidingbiker.com/podcast Join our free email club at /www.LawAbidingBiker.com/EmailClub. Only relevant content will be sent from time to time. Email club members are the first to find out about free or for sale content are given special coupon codes.