No video :(

Home Automation using arduino bluetooth | Smart Home | Manual and smartphone | part 1

Подписаться 9 тыс.

Просмотров 218 тыс.

50% 1

The home automation circuit is built around an Arduino Uno board, Bluetooth module HC-05 and a 1-channel relay board. The number of channels depends on the number of appliances you wish to control. Arduino Uno is powered with a 12V DC adaptor/power source.
This channel to share exciting videos of Arduino projects,Electronics and electrical easy diy projects to share with you I hope this projects will be helpful for you to create something new .
Do not Forget to like comment and subscribe my channel.
SUBSCRIBE LINK:-
/ @slideas1
Arduino Code :-
www.mediafire.com/folder/4ovq...
My Other videos :-
1. How to control DC motor and Stepper motor with L293d motor driver Arduino
• How to control DC moto...
2. l298n motor driver with control DC motor & speed control unipoler & bipoler stepper motor
• l298n motor driver wit...
3. servo motor arduino
• servo motor arduino |...
4. Top arduino projects 2021 for covid 19 | coronavirus protector | Sterilize Stationery
• Top arduino projects 2...
5. NEMA 23 | NEMA 17 | NEMA 34 with TB6600 stepper motor driver and Arduino
• NEMA 23 | NEMA 17 | NE...
6. How to Build a Low-Cost RU-vid Studio
• How to Build a Low-Cos...
7. How to use W1219 Temperature controller/DUAL Display
• How to use W1219 Tempe...
8. How to make an LED VU-meter using Arduino.
• How to make an LED VU-...
9. LED chaser with 32 effects |led patterns with Arduino | Code in Discription
• LED chaser with 32 eff...
10. How To Make Automatic Touch Less Non Contact Water Tap At Home/office
• How To Make Automatic ...
11. How to make best car reverse parking alert system using arduino / DIY / arduino projects
• How to make best car r...
#HomeAutomation #ArduinoBluetooth #SmartPhone
projects,and,products,home automation,How to make home automation using Arduino and bluetooth,how to make home automation project,home automation projects,home automation using bluetooth module,hc 05 bluetooth module interface with arduino,hc 05 bluetooth module working,Bluetooth module hc-05 with Arduino,home automation in hindi,bluetooth based home automation,bluetooth based projects,automation,home,home automation using arduino and bluetooth
home automation using arduino,home automation project,home automation arduino hindi,home automation arduino uno hindi,home automation using arduino uno and bluetooth module,control room lights with arduino,control room lights with mobile,home automation using arduino and bluetooth,home automation,home automation with bluetooth,home automation arduino projects,home automation arduino projects hindi,arduino projects hindi,arduino projects with code,harsh sharma,omhome automation,arduino projects,smart home,homeautomation easy,arduino,mrarduino,project for begineers,home automation bluetooth,home automation x,home automation ideas,home automation system,home automation 2019,home automation diy,home automation hub,home automation india,home automation arduino,home automation arduino project,home automation arduino uno,home automation bangladesh,home automation by arduino,home automation best,home automation cheaphome automation,wifi,bluetooth,blynk,application,app,smartphone,controlled,how to make,work,tutorial,how to control,appliances,devices,lights,fans,code,program,mit app inventor,development,how to make app,raspberry pi,arduino,relay,design,wireless,viral science,viral dodhia,easy,free,project,final year,build,connection,automate,house,home,automation,google assistant,ok google,voice,gsm,gps,command,robot

Опубликовано:

9 апр 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 217

@Sazia_Cooking_Creativity 2 года назад

Wonderful video Thanks Brother

@slideas1 2 года назад

Thank u bro....

@user-js6lb9pf4p 5 месяцев назад

nice👌

@osmondbooysen9641 7 месяцев назад

Great tutorial. How would we connect this in a way that allows switching it off via bluetooth if its manually switched on?

@h.a.7393 2 года назад

Thank you, This video is a useful, informative, simple and clear description.

@slideas1 2 года назад

Thank u very much .....❤

@harryskay617 Месяц назад

Did it work for you

@MR_VINIX_ Год назад

niyamai kollo

@slideas1 Год назад

Thank u

@suranjanghimire659 7 месяцев назад

Thank you

@ayodsanjutha 4 месяца назад

සුපිරි වැඩක් bro😃

@slideas1 Месяц назад

Thank u bro

@Drxxx 3 года назад

Great video

@slideas1 3 года назад

thank u soo much

@VivekGupta-xp2np 3 года назад

Nice Dear , tried with many video but this one really solve my issue. thanks

@slideas1 3 года назад

Thank u

@ICTBLACKBELT 3 года назад

නියමයි සහෝදරයා

@slideas1 3 года назад

ගොඩක් ස්තුතියි සහොදරයා

@MdAbdullah-qz1dg 2 месяца назад

@@slideas112:47

@naveenwilliam3594 2 года назад

Hello bro i have a small doubt if the bulb is manually on through the switch can i turn it off with bluetooth and vice versa and i dont know how to wire it that way can you tell me how to do that if you know plz

@atiya_belim 2 года назад

Hey . Please tell me the code will be same for different Arduino right Mine is slightly different so this code will work?

@multinogaming07 Год назад

Can we control our room c link fan by Arduino Uno by proper circuit structure?

@Allroundtube--113 8 месяцев назад

Can i use it over long distance???

@user-mo5mw5mq8z Год назад

your outcome is different to your circuit diagram, in your diagram the arduino is powered by the 220V AC but in your actual circuit it's powered by 9V DC. Is there any chance of getting the diagram with the physical switch and 9V DC adapter?

@donaldiro5398 11 месяцев назад

Can this work with HC 04 Bluetooth module

@VishalMudgal-gw5jn Год назад

Define Pin 13. And I think the Circuit is very easy.

@aljayramos5437 3 месяца назад

can I use other type of switch?

@reynaldoacobajr.9006 Месяц назад

better to use 3-way switch so that you can turn on/off thru phone or switch. in that way, the logic will be like XOR.

@jailbreak7750 Год назад

turn on switch don't switch off, stay on. turn off from u'r handphone. is it safe?

@chidiayoanasonye9243 2 года назад

Plz I don't have a PC . how can I upload the code using my android phone. I tried with arduino droid IDE app on my android phone and all I could get is a blinking relay and light connected to the relay . Why is it not turning on and off through Bluetooth controller app on my phone ? . plz assist

@uwiringiyimanawilson3473 2 года назад

you are a good teacher. by the way, can you teach me how to make arduino programing

@slideas1 2 года назад

Welcome and following my channel .....

@bgm4019 2 года назад

Bro can I use hm 10 blutooth module instead of hc 05 and need to make some changes in code please reply

@mariaalmeida761 Год назад

hello, I am not able to open the arduino code link, can you make it available in another way?

@djblanscky Год назад

my bluetooth module is JDY-31 how can i do to pair it.

@Power.oftruth Год назад

Hello sir please how to upload aurdino code please provide information step wise Please reply sir 😊😊

@AbdulMajid-vn8lw 2 года назад

Hello, your given link for downloading the code isn't working. Please share the code.

@haroonali1988 2 года назад

Can you give the link of application that you are using

@Kaunderdasen1 2 года назад

Do you have coding if we want to implement voice control for this exact project?

@slideas1 2 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hkOUWIv6v-w.html

@gameofdeath1731 2 года назад

can it be any codeing issue

@amzsingh6376 Год назад

Thank you Bro, one trick that can fullfill my 5-6 hr, please remove RX and TX pin before uplode code

@slideas1 Год назад

Thank u

@shaheryaraslamm 2 года назад

When we are entering password for Bluetooth It is going in saved not connecting.. please explain

@Art_Raunak Год назад

Bro ye program nano me ho jaega

@rKj4795 2 года назад

What if we don't use adapter ?

@silversurfur69 Год назад

I followed the video but my bulb didn't glow what to do

@chibingwei761 2 года назад

May I ask did this system can connect more than 3 bulbs? did you have some examples to refer to?

@revanth5563 2 года назад

No bro you should have extra relay modules. But it is possible for 3 bulbs at a time to work with single relay module

@mdtareqrahman3163 3 года назад

How much arduino and relay?

@ranjithbandara4950 3 года назад

Aiye oya Arduino uno Programming karala den නැතිද ..oyata permanent කළොත්..

@silversurfur69 Год назад

hey which arduino are you using? arduino r3?

@slideas1 Год назад

Yes arduino uno r3

@swapnalipadaval5449 9 дней назад

What is the component of 220V Ac plz tell me name of this component

@dilshankasthuriarachchi4737 3 года назад

Hi there gm is this relay module without optocoupler?

@slideas1 3 года назад

GM ,yes without optocoupler.......

@zeeshanmuhammad1114 2 года назад

@@slideas1 any vedio about to control geyser according to your timing and temperature

@gameofdeath1731 2 года назад

the green is also like low voltage

@sanjingot6486 Год назад

What is the name of the wires you used to connect the relay module, light bulb, and switch?

@sasmitasahoo1787 7 месяцев назад

Jumper cables Three categories M-M F-F M-F

@yupadyy204 Год назад

Hello, I am from Indonesian Can I ask what happened when we turn on the light with Bluetooth and we disconnect Bluetooth with Arduino? Are the light will turn off?

@slideas1 Год назад

If the bulb was lit at the time of disconnecting the bluetooth, it will continue to be lit in the same way. If the bulb is off The bulb is still off.

@gameofdeath1731 2 года назад

relay module is not letting current to flow on bulb

@danielikhmall3539 2 года назад

Can we switch off the light using phone eventhough the switch button is on?

@jb_labs 2 года назад

I'm pretty sure you can. It seems both the switch and Arduino is connected to the same terminal on the light bulb, so arduino can turn on the lightbulb, regardless if the switch is off. U could think of it as a OR gate Problem is, if the light switch is on, then it cannot be turned of via the app, it needs to be done by the light switch. And same if the app is on, the app is only way to turn off.

@gameofdeath1731 2 года назад

i have bought 12 v i can observe the green light turning on and off.but bulb is not glowing i checked connection

@nathanieldavidmodesto3243 8 месяцев назад

Same.problem brother, have you resolved it yet?

@-nikomcace7855 3 года назад

What if I turn the light on with Bluetooth and turn the switch off ? Will the light be on or off ?

@slideas1 3 года назад

This way the bulb does not turn off.

@sanjaysaravana7218 2 года назад

What if I on both of them

@armylovergolusinghrajput3618 3 месяца назад

Three bulb lagar kar ek video bana dijiye

@techwithalan7554 2 года назад

Bro can we connect 12v dc adapter to the bulb

@slideas1 2 года назад

It works with 230v A / C supply. If desired, a 12v D / C supply can be provided and a 12v adapter can be connected to this.

@karangamer3865 4 месяца назад

From where i can order this model

@bkcganeshblogs 6 месяцев назад

How to increase buttons in Arduino bluetooth control App .only 6 are provided.

@bkcganeshblogs 6 месяцев назад

Give me answer sir

@MathiTamilGaming 2 года назад

What if we turn ON both the Switches ( Mobile and Manual) ?

@slideas1 2 года назад

Bulb on

@kkr_gaming_ Год назад

What is the exact price

@polepeddibharat1315 Год назад

Bro program kinda description lo ledu bro okasari program link petava bro plz

@allsongs1729 2 года назад

Sir, it is okay if I use HC-06 Bluetooth module?

@slideas1 2 года назад

Yes

@allsongs1729 2 года назад

@@slideas1 Thank you sir, I subscribed to your channel

@slideas1 2 года назад

@@allsongs1729 welcome

@tienngo6357 10 месяцев назад

Can i have a Diagram of this project Sir ?

@sherollin Год назад

can we still control even we going out...that far from home

@Saiteja-bg9gj Год назад

No we can't cause Bluetooth range is not so far, for that a wifi controller need to installed in your home.

@tumpalasindhu5382 Год назад

everything is good but light doesn't controlled with bluetooth. what is the reason? what can i do to make light controlled by bluetooth app?

@dammdaniel9953 7 месяцев назад

Jumper wires

@EWaB-ou4lc 4 месяца назад

May be that you did not connected the system correctly

@libinmathew1068 4 месяца назад

Bulb 💡 glow chythooo???? Reply

@gameofdeath1731 2 года назад

how should we erase old command

@meeraliakbar12 2 года назад

Can i do this project with arduino nano??

@slideas1 2 года назад

Yes of cose

@bettgilbert7781 2 года назад

Great video sir, can I have a code, please?

@slideas1 2 года назад

Thank u...code in discription ..download ...

@osmanelkinani 7 месяцев назад

There is a fatal error in that you are powering the lamp from 220 volts from the relay and the switch side

@norbertkiss112 Год назад

Pls code 8ch relay panel.

@chidiayoanasonye9243 2 года назад

Could you please show step by step on how to program the auduino

@slideas1 2 года назад

Good idea ...👍

@karlsaariste Год назад

you can also just download the code

@vinay6492 11 месяцев назад

Complete circuit was working but had a problem with the bulb it's not glowing

@nathanieldavidmodesto3243 8 месяцев назад

Have you resolved your problem? Regarding the bulb not glowing?? Do you face any problems when you upload your code?

@leonelolvera9560 2 года назад

Es un interruptor de 2 vías ???

@jb_labs 2 года назад

Unfortunately not. If one is on, then it cannot be turned off by other ie AND gate

@supritgawande8261 8 месяцев назад

Can you please send this programing link ? The link given by you is not opening

@slideas1 8 месяцев назад

Code in discription ...download

@arielmvoto3012 Год назад

Salut peux tu m'envoyer le lien du code bluetooth s'il te plaît

@Chujie28 2 года назад

Hello sir can i get a new programing coding link , the link on description is expired

@slideas1 2 года назад

char val; void setup() { pinMode(13,OUTPUT); Serial.begin(9600); digitalWrite(13,HIGH); } void loop() { if(Serial.available()){ val = Serial.read(); Serial.println(val); } if(val=='1'){ digitalWrite(13,LOW); } else if(val=='2'){ digitalWrite(13,HIGH); } delay(100); }

@piyushkumarIITD Год назад

Hi all, I'm unable to open the Arduino code link, can you make it available in another way?

@slideas1 Год назад

E malli please ?

@bharadwajthangella-bz9jv 7 месяцев назад

Bro i need the correct code

@rahulshahane6383 Год назад

There is analysis in my uno r3 board , perhaps I had not been completed my project 😢

@rahulshahane6383 Год назад

Is Unor3 is suitable for this project ?

@keep-lung-heart.6689 Год назад

hello bro the code is not working

@rabiulislam3406 2 года назад

app link plz

@brucewayne54321 Год назад

Price kitna hai bhai ?

@boringmemes5718 2 года назад

Sir the code given in the discription gone expired an alternate code for it ?

@slideas1 2 года назад

Send mail

@boringmemes5718 2 года назад

@@slideas1 i don't have mail please send the code in comment section

@Payalgamingfan20 2 года назад

Bro can we turn on 4 bulbs

@slideas1 2 года назад

Yes ,4 relay module and modify code....

@Payalgamingfan20 2 года назад

@@slideas1 thanku very much

@youcan6808 2 года назад

can you give the buy link

@slideas1 2 года назад

Free

@qadeer1685 2 года назад

Arduino uno Bluetooth 4 channel relay

@gameofdeath1731 2 года назад

codeing any thing we have to change a bro

@polepeddibharat1315 Год назад

Bro nidhehara program vunthe naku petu link petu bro

@gameofdeath1731 2 года назад

bro how much volts relay module

@slideas1 2 года назад

This 12v relay ..if u want u can used 5v relay module

@raj1.88. 2 года назад

Code was which language

@tradingview5363 Год назад

cAN I RUN A CIELING FAN INSTEAD OF BULB?

@slideas1 Год назад

Yes definitely

@rishith3010 3 года назад

How can we connect multiple lights in this?

@slideas1 3 года назад

Use a model with several relays

@danielikhmall3539 2 года назад

But do we need to change the coding?

@kingofscience1437 2 года назад

How much distance it can work

@slideas1 2 года назад

20 - 30 meters

@kingofscience1437 2 года назад

Thanks 👍 bro

@uwiringiyimanawilson3473 2 года назад

plz help us to study arduino code

@Tukaram_Achugatla Год назад

The Code file is not opening...😥

@madhyamdhartalvar 2 месяца назад

Bro सही से open कर

@salmamulla8572 2 года назад

What about that wires ... What are they called....

@slideas1 2 года назад

Jumper wire and auto wire

@SyedAun-dn8tu 2 месяца назад

circuit diagram?

@umairahauni6381 2 года назад

do you have the code for arduino?

@slideas1 2 года назад

Code in discription ....download ..

@bunnyshhh3020 2 года назад

Count download arduino code.🙁

@kulesiswarkulesh2032 2 года назад

Hi sir

@slideas1 2 года назад

@maheshparmar2655 4 месяца назад

Program kese Lena hei

@asada1939 3 года назад

What happen if both switches and bluetooth turn on

@slideas1 3 года назад

Even then the bulb is on

@jonalddejesus6726 2 года назад

it looks like a 3way switch

@dhanooshb2871 2 года назад

How to download that application which we can connect in bluetooth

@slideas1 2 года назад

Click the arduino library link to download

@badabomaxime7053 2 года назад

svp je veux que vous m'expliquer comment faire pour créé le code c'est inpeut floue pour moi svp sinon j'aime votre video

@JOYNALABEDIN-tb5cr 3 года назад

where is your cod

@kulesiswarkulesh2032 2 года назад

Hir sir...can add fan in this project...how it in circuit and the coding....please explain...

@kulesiswarkulesh2032 2 года назад

Please reply

@slideas1 2 года назад

@@kulesiswarkulesh2032 yes can

@kulesiswarkulesh2032 2 года назад

@@slideas1 how I contact you sir...

@kulesiswarkulesh2032 2 года назад

Can I get your email...

@slideas1 2 года назад

@@kulesiswarkulesh2032 following my face book page..👍👍👍

@techwithalan7554 2 года назад

Bro the code was not open pls put the code on comment pls

@slideas1 2 года назад

@dnyandeotembare5064 2 года назад

4 relay program code chahiye